Rong Xue
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Rong Xue has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Yu Hou
MOE Key Laboratory of Cryogenic Technology and Equipment, Xi'an Jiaotong University 1 , Xi'an 710049
6 shared publications - Beile Zhang
School of Energy and Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China
4 shared publications - Liang Chen
State Key Laboratory of Multiphase Flow in Power Engineering, Xi’an Jiaotong University, Xi’an, China
3 shared publications - Xinyi Lin
School of Energy and Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China
3 shared publications - Shuangtao Chen
School of Energy and Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China
2 shared publications - Tianwei Lai
State Key Laboratory of Multiphase Flow in Power Engineering, Xi’an Jiaotong University, Xi’an, China
2 shared publications
Latest Publications
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
Machine learning analysis of boiling regimes and spreading dynamics in liquid nitrogen droplet impact on superheated surfaces
The impact of liquid nitrogen droplets on superheated surfaces involves a complex interplay of transient fluid flow, heat transfer, and phase change phenomena, all of which critically influence the efficiency of spray cooling systems. To investigate this behavior, we develop two machine learning models: one for classifying boiling regimes upon droplet impact and another for predicting spreading dynamics across the regimes. A dataset of 5274 experimentally obtained impact images is used to evaluate seven convolutional neural network architectures with ResNet-18 achieving the highest classification accuracy of 99.8%. Based on this classification, a multilayer perceptron model is trained using five key parameters—Reynolds number, Weber number, Ohnesorge number, Capillary number, and surface temperature—to predict the maximum spreading coefficient and spreading time. Compared to traditional empirical methods, our models significantly improve predictive accuracy, reducing errors to below 4.8% and 8.4% for the respective parameters. In addition to deepening the fundamental understanding of cryogenic droplet dynamics, this machine learning-based framework offers valuable potential for optimizing the design and performance of cryogenic cooling systems.
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
Machine learning analysis of boiling regimes and spreading dynamics in liquid nitrogen droplet impact on superheated surfaces
The impact of liquid nitrogen droplets on superheated surfaces involves a complex interplay of transient fluid flow, heat transfer, and phase change phenomena, all of which critically influence the efficiency of spray cooling systems. To investigate this behavior, we develop two machine learning models: one for classifying boiling regimes upon droplet impact and another for predicting spreading dynamics across the regimes. A dataset of 5274 experimentally obtained impact images is used to evaluate seven convolutional neural network architectures with ResNet-18 achieving the highest classification accuracy of 99.8%. Based on this classification, a multilayer perceptron model is trained using five key parameters—Reynolds number, Weber number, Ohnesorge number, Capillary number, and surface temperature—to predict the maximum spreading coefficient and spreading time. Compared to traditional empirical methods, our models significantly improve predictive accuracy, reducing errors to below 4.8% and 8.4% for the respective parameters. In addition to deepening the fundamental understanding of cryogenic droplet dynamics, this machine learning-based framework offers valuable potential for optimizing the design and performance of cryogenic cooling systems.
- Open Access
Hydraulic Performance and Flow Characteristics of a High-Speed Centrifugal Pump Based on Multi-Objective Optimization
Pump-driven liquid cooling systems are widely utilized in unmanned aerial vehicle (UAV) electronic thermal management. As a critical power component, the miniaturization and lightweight design of the pump are essential. Increasing the operating speed of the pump allows for a reduction in impeller size while maintaining hydraulic performance, thereby significantly decreasing the overall volume and mass. However, high-speed operation introduces considerable internal flow losses, placing stricter demands on the geometric design and flow-field compatibility of the impeller. In this study, a miniature high-speed centrifugal pump (MHCP) was investigated, and a multi-objective optimization of the impeller was carried out using response surface methodology (RSM) to improve internal flow characteristics and overall hydraulic performance. Numerical simulations demonstrated strong predictive capability, and experimental results validated the model’s accuracy. At the design condition (10,000 rpm, 4.8 m3/h), the pump achieved a head of 46.1 m and an efficiency of 49.7%, corresponding to its best efficiency point (BEP). Sensitivity analysis revealed that impeller outlet diameter and blade outlet angle were the most influential parameters affecting pump performance. Following the optimization, the pump head increased by 3.7 m, and the hydraulic efficiency improved by 4.8%. In addition, the pressure distribution and streamlines within the impeller exhibited better uniformity, while the turbulent kinetic energy near the blade suction surface and at the impeller outlet was markedly decreased. This work provides theoretical support and design guidance for the efficient application of MHCPs in UAV thermal management systems.
Open AccessHydraulic Performance and Flow Characteristics of a High-Speed Centrifugal Pump Based on Multi-Objective Optimization
Pump-driven liquid cooling systems are widely utilized in unmanned aerial vehicle (UAV) electronic thermal management. As a critical power component, the miniaturization and lightweight design of the pump are essential. Increasing the operating speed of the pump allows for a reduction in impeller size while maintaining hydraulic performance, thereby significantly decreasing the overall volume and mass. However, high-speed operation introduces considerable internal flow losses, placing stricter demands on the geometric design and flow-field compatibility of the impeller. In this study, a miniature high-speed centrifugal pump (MHCP) was investigated, and a multi-objective optimization of the impeller was carried out using response surface methodology (RSM) to improve internal flow characteristics and overall hydraulic performance. Numerical simulations demonstrated strong predictive capability, and experimental results validated the model’s accuracy. At the design condition (10,000 rpm, 4.8 m3/h), the pump achieved a head of 46.1 m and an efficiency of 49.7%, corresponding to its best efficiency point (BEP). Sensitivity analysis revealed that impeller outlet diameter and blade outlet angle were the most influential parameters affecting pump performance. Following the optimization, the pump head increased by 3.7 m, and the hydraulic efficiency improved by 4.8%. In addition, the pressure distribution and streamlines within the impeller exhibited better uniformity, while the turbulent kinetic energy near the blade suction surface and at the impeller outlet was markedly decreased. This work provides theoretical support and design guidance for the efficient application of MHCPs in UAV thermal management systems.
- 1 November 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (11)
Tip clearance influence on the performance of high-speed micro-pumps
The fast-paced development of the aerospace and shipping industry is promoting the development of lightweight and high-speed transfer pumps. High-speed micro-pumps with semi-open impellers are highly sensitive to tip clearance (TC), which crucially influences the head and efficiency. This study proposes a new design for a high-speed micro-semi-open impeller centrifugal pump with a 19 000 rpm rotational speed and 30 m hydraulic head. The performance of the proposed centrifugal pump under different inlet corrosion allowances and different impeller TC ratios (0.05, 0.08, 0.11, and 0.14) is investigated through numerical simulations and experiments. The interaction process between the leakage and main flows in the tip gap is recorded with a high-speed camera and is numerically calculated. The stability of the internal flow field is optimal under smaller TCs. This study provides the optimal TC and guidance for designing high-speed micro-pumps.
- 1 November 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (11)
Tip clearance influence on the performance of high-speed micro-pumps
The fast-paced development of the aerospace and shipping industry is promoting the development of lightweight and high-speed transfer pumps. High-speed micro-pumps with semi-open impellers are highly sensitive to tip clearance (TC), which crucially influences the head and efficiency. This study proposes a new design for a high-speed micro-semi-open impeller centrifugal pump with a 19 000 rpm rotational speed and 30 m hydraulic head. The performance of the proposed centrifugal pump under different inlet corrosion allowances and different impeller TC ratios (0.05, 0.08, 0.11, and 0.14) is investigated through numerical simulations and experiments. The interaction process between the leakage and main flows in the tip gap is recorded with a high-speed camera and is numerically calculated. The stability of the internal flow field is optimal under smaller TCs. This study provides the optimal TC and guidance for designing high-speed micro-pumps.
- Open Access
Application and Challenge of High-Speed Pumps with Low-Temperature Thermosensitive Fluids
The rapid development of industrial and information technology is driving the demand to improve the applicability and hydraulic performance of centrifugal pumps in various applications. Enhancing the rotational speed of pumps can simultaneously increase the head and reduce the impeller diameter, thereby reducing the pump size and weight and also improving pump efficiency. This paper reviews the current application status of high-speed pumps using low-temperature thermosensitive fluids, which have been applied in fields such as novel energy-saving cooling technologies, aerospace, chemical industries, and cryogenic engineering. Due to operational constraints and thermal effects, there are inherent challenges that still need to be addressed for high-speed pumps. Based on numerical simulation and experimental research for different working fluids, the results regarding cavitation within the inducer have been categorized and summarized. Improvements to cavitation models, the mechanism of unsteady cavity shedding, vortex generation and cavitation suppression, and the impact of cavitation on pump performance were examined. Subsequently, the thermal properties and cavitation thermal effects of low-temperature thermosensitive fluids were analyzed. In response to the application requirements of pump-driven two-phase cooling systems in data centers, a high-speed refrigerant pump employing hydrodynamic bearings has been proposed. Experimental results indicate that the prototype achieves a head of 56.5 m and an efficiency of 36.1% at design conditions (n = 7000 rpm, Q = 1.5 m3/h). The prototype features a variable frequency motor, allowing for a wider operational range, and has successfully passed both on/off and continuous operation tests. These findings provide valuable insights for improving the performance of high-speed refrigerant pumps in relevant applications.
Open AccessApplication and Challenge of High-Speed Pumps with Low-Temperature Thermosensitive Fluids
The rapid development of industrial and information technology is driving the demand to improve the applicability and hydraulic performance of centrifugal pumps in various applications. Enhancing the rotational speed of pumps can simultaneously increase the head and reduce the impeller diameter, thereby reducing the pump size and weight and also improving pump efficiency. This paper reviews the current application status of high-speed pumps using low-temperature thermosensitive fluids, which have been applied in fields such as novel energy-saving cooling technologies, aerospace, chemical industries, and cryogenic engineering. Due to operational constraints and thermal effects, there are inherent challenges that still need to be addressed for high-speed pumps. Based on numerical simulation and experimental research for different working fluids, the results regarding cavitation within the inducer have been categorized and summarized. Improvements to cavitation models, the mechanism of unsteady cavity shedding, vortex generation and cavitation suppression, and the impact of cavitation on pump performance were examined. Subsequently, the thermal properties and cavitation thermal effects of low-temperature thermosensitive fluids were analyzed. In response to the application requirements of pump-driven two-phase cooling systems in data centers, a high-speed refrigerant pump employing hydrodynamic bearings has been proposed. Experimental results indicate that the prototype achieves a head of 56.5 m and an efficiency of 36.1% at design conditions (n = 7000 rpm, Q = 1.5 m3/h). The prototype features a variable frequency motor, allowing for a wider operational range, and has successfully passed both on/off and continuous operation tests. These findings provide valuable insights for improving the performance of high-speed refrigerant pumps in relevant applications.
- Open Access
- 10 July 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (14) , 8062
Numerical and Experimental Investigation of Flow Characteristics in a Fluid Self-Lubricating Centrifugal Pump with R134a Refrigerant
With the rapid development of information technology, researchers have paid attention to the pump-driven two-phase cooling loop technology for data centers, which imposes requirements on the efficiency and size of the pump. A fluid self-lubricating centrifugal pump with R134a refrigerant was developed to reach a higher rotation speed and oil-free system, resulting in a more diminutive size. Due to the high rotation speed and refrigerant pressure approaching saturated vapor pressure, the internal flow characteristics and cavitating characteristics are critical and complex. This paper focuses on the prototype’s head and cavitation performance based on experimental and numerical data. The experiments indicated that the head coefficient of the pump under design conditions is 0.9881, and the pump’s critical cavitation number and breakdown number are 0.551 and 0.412, respectively. The numerical results can predict the head and cavitation with deviations less than 2.6%. To study changing patterns in flow characteristics under the different operating conditions in the refrigerant centrifugal pump, the numerical model based on a modified Sauer-Schnerr cavitation model was built to analyze the distributions of pressure, temperature, relative velocity, and bubble volume across every hydraulic component and different degrees of cavitation, and proposed the influence of the thermal effect on refrigerant cavitating. The cavitating flow characteristics were obtained with the aim of providing guidance for the hydraulic design of a refrigerant centrifugal pump.
- 10 July 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (14) , 8062
Open AccessNumerical and Experimental Investigation of Flow Characteristics in a Fluid Self-Lubricating Centrifugal Pump with R134a Refrigerant
With the rapid development of information technology, researchers have paid attention to the pump-driven two-phase cooling loop technology for data centers, which imposes requirements on the efficiency and size of the pump. A fluid self-lubricating centrifugal pump with R134a refrigerant was developed to reach a higher rotation speed and oil-free system, resulting in a more diminutive size. Due to the high rotation speed and refrigerant pressure approaching saturated vapor pressure, the internal flow characteristics and cavitating characteristics are critical and complex. This paper focuses on the prototype’s head and cavitation performance based on experimental and numerical data. The experiments indicated that the head coefficient of the pump under design conditions is 0.9881, and the pump’s critical cavitation number and breakdown number are 0.551 and 0.412, respectively. The numerical results can predict the head and cavitation with deviations less than 2.6%. To study changing patterns in flow characteristics under the different operating conditions in the refrigerant centrifugal pump, the numerical model based on a modified Sauer-Schnerr cavitation model was built to analyze the distributions of pressure, temperature, relative velocity, and bubble volume across every hydraulic component and different degrees of cavitation, and proposed the influence of the thermal effect on refrigerant cavitating. The cavitating flow characteristics were obtained with the aim of providing guidance for the hydraulic design of a refrigerant centrifugal pump.
- Open Access
- 24 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (15) , 7435
CFD and Energy Loss Model Analysis of High-Speed Centrifugal Pump with Low Specific Speed
High-speed centrifugal pumps with low specific speed have the characteristics of a small flowrate, a high head, and being compact and light weight, making them promising candidates for applications in the thermal management of aerospace and electronic devices. The energy loss in the low specific speed pump is critical and complex due to the large impeller diameter, the narrow and long flow channel, and the small outlet width. In this paper, an analysis method based on an energy loss model and computational fluid dynamics simulations (ELM/CFD) is proposed to analyze the performance of the low specific speed pump with a fully sealed structure. Experiments were carried out under variable water flowrates. The results show that the empirical correlation method failed to accurately predict the performance of high-speed centrifugal pumps, because the bearing clearance leakage and motor channel leakage are ignored. Moreover, the volume loss and hydraulic loss are calculated based on the empirical parameters of commonly used pumps that are different from the high-speed pump with the low specific speed in the complex flow channel structure. The ELM/CFD method calculates various loss power based on the simulation results and can predict the head and efficiency with deviations less than 2% and 5%, respectively. ELM/CFD can accurately analyze the optimization direction of the pump. The hydraulic loss and the volume loss of the impeller are the dominant factors that restrict the pump efficiency under the lower flowrates, while the hydraulic loss of subsequent flow channels becomes important under the larger flowrates.
- 24 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (15) , 7435
Open AccessCFD and Energy Loss Model Analysis of High-Speed Centrifugal Pump with Low Specific Speed
High-speed centrifugal pumps with low specific speed have the characteristics of a small flowrate, a high head, and being compact and light weight, making them promising candidates for applications in the thermal management of aerospace and electronic devices. The energy loss in the low specific speed pump is critical and complex due to the large impeller diameter, the narrow and long flow channel, and the small outlet width. In this paper, an analysis method based on an energy loss model and computational fluid dynamics simulations (ELM/CFD) is proposed to analyze the performance of the low specific speed pump with a fully sealed structure. Experiments were carried out under variable water flowrates. The results show that the empirical correlation method failed to accurately predict the performance of high-speed centrifugal pumps, because the bearing clearance leakage and motor channel leakage are ignored. Moreover, the volume loss and hydraulic loss are calculated based on the empirical parameters of commonly used pumps that are different from the high-speed pump with the low specific speed in the complex flow channel structure. The ELM/CFD method calculates various loss power based on the simulation results and can predict the head and efficiency with deviations less than 2% and 5%, respectively. ELM/CFD can accurately analyze the optimization direction of the pump. The hydraulic loss and the volume loss of the impeller are the dominant factors that restrict the pump efficiency under the lower flowrates, while the hydraulic loss of subsequent flow channels becomes important under the larger flowrates.
- Open Access
- 23 May 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (10) , 5263
Influence of Internal Flow on the Performance of High-Speed Centrifugal Pumps with a Fully Sealed Structure
A high-speed centrifugal pump with a fully sealed structure has the advantages of a small size, no external leakage, and being pollution-free. The inner leakage passage of a pump with a fully sealed structure includes the tip clearance and the hub clearance. The hub clearance, the lubrication passage of the bearing, and the clearance between the stator and the rotor of the built-in motor constitute the internal flow channel. As a consequence of hub leakage, the complexity of the flow field increases and performance of the pump is affected. However, hub leakage also lubricates the bearing and cools the motor by flowing through the internal flow channel. To obtain the actual flow field distribution and external characteristics of the pump, a coupling calculation based on a conventional CFX simulation and MATLAB was carried out. The results show that hub leakage promotes an increase in tip leakage and changes the distribution of the main flow field. Moreover, hub leakage also significantly affects the efficiency of the pump. Compared with hub leakage, the internal flow has a greater impact on the performance of the pump. The numerical simulation results of the internal flow model are similar to the experimental results, with the maximum absolute error of the head at 0.3 m and the maximum absolute error of the efficiency at 1.7%, indicating that the internal flow model is effective at predicting the performance of the high-speed centrifugal pump with a fully sealed structure.
- 23 May 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (10) , 5263
Open AccessInfluence of Internal Flow on the Performance of High-Speed Centrifugal Pumps with a Fully Sealed Structure
A high-speed centrifugal pump with a fully sealed structure has the advantages of a small size, no external leakage, and being pollution-free. The inner leakage passage of a pump with a fully sealed structure includes the tip clearance and the hub clearance. The hub clearance, the lubrication passage of the bearing, and the clearance between the stator and the rotor of the built-in motor constitute the internal flow channel. As a consequence of hub leakage, the complexity of the flow field increases and performance of the pump is affected. However, hub leakage also lubricates the bearing and cools the motor by flowing through the internal flow channel. To obtain the actual flow field distribution and external characteristics of the pump, a coupling calculation based on a conventional CFX simulation and MATLAB was carried out. The results show that hub leakage promotes an increase in tip leakage and changes the distribution of the main flow field. Moreover, hub leakage also significantly affects the efficiency of the pump. Compared with hub leakage, the internal flow has a greater impact on the performance of the pump. The numerical simulation results of the internal flow model are similar to the experimental results, with the maximum absolute error of the head at 0.3 m and the maximum absolute error of the efficiency at 1.7%, indicating that the internal flow model is effective at predicting the performance of the high-speed centrifugal pump with a fully sealed structure.
- Open Access
Numerical Study of the Effects of Injection Fluctuations on Liquid Nitrogen Spray Cooling
Spray cooling with liquid nitrogen is increasingly utilized as an efficient approach to achieve cryogenic cooling. Effects of injection mass flow rate fluctuations on the evaporation, temperature distribution, and droplet distribution of a spray field were examined by employing a validated Computational Fluid Dynamics (CFD) numerical model. The numerical results indicated that injection fluctuations enhanced the volume-averaging turbulent kinetic energy and promoted the evaporation of the whole spray field. The strengthened mass and heat transfer between the liquid nitrogen droplets and the surrounding vapor created by the fluctuating injection led to a lower temperature of the whole volume. A relatively smaller droplet size and a more inhomogeneous droplet distribution were obtained under the unsteady inlet. The changes of the frequency and the amplitude of the fluctuations had little effects on the overall spray development. The results could enrich the knowledge of the relation between the inevitable fluctuations and the overall spray development and the cooling performance in a practical spray cooling system with cryogenic fluids.
Open AccessNumerical Study of the Effects of Injection Fluctuations on Liquid Nitrogen Spray Cooling
Spray cooling with liquid nitrogen is increasingly utilized as an efficient approach to achieve cryogenic cooling. Effects of injection mass flow rate fluctuations on the evaporation, temperature distribution, and droplet distribution of a spray field were examined by employing a validated Computational Fluid Dynamics (CFD) numerical model. The numerical results indicated that injection fluctuations enhanced the volume-averaging turbulent kinetic energy and promoted the evaporation of the whole spray field. The strengthened mass and heat transfer between the liquid nitrogen droplets and the surrounding vapor created by the fluctuating injection led to a lower temperature of the whole volume. A relatively smaller droplet size and a more inhomogeneous droplet distribution were obtained under the unsteady inlet. The changes of the frequency and the amplitude of the fluctuations had little effects on the overall spray development. The results could enrich the knowledge of the relation between the inevitable fluctuations and the overall spray development and the cooling performance in a practical spray cooling system with cryogenic fluids.
- Open Access
- 29 July 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (15) , 3050
Optimization Study on a Novel High-Speed Oil-Free Centrifugal Water Pump with Hydrodynamic Bearings
In aerospace fields and industrial sectors, high-speed centrifugal pumps are prevalent and in increasingly strict demand regarding characteristics such as the long life, small volume, light weight, and low noise. In this study, we present a novel high-speed centrifugal water pump with hydrodynamic bearings used to employ work fluid as lubricant. A three-dimensional numerical study of the turbulent fluid flow was carried out to predict the performance of the pump. The computational model was validated against experimental results during hydraulic tests. Additionally, the effect of the blade number on the head and efficiency of the pump was researched. The blade number of the impeller was changed from 4 to 8 and that of the stay vane was from 3 to 14. The results indicate that the blade number and the matching characteristic of the impeller and the stay vane significantly influenced the performance of the pump. The structure based on the seven-blade impeller and the six-blade stay vane had the highest efficiency (30.8%). Numerical investigations of this study may help reduce the significant cost and time of experimental work for a particular design.
- 29 July 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (15) , 3050
Open AccessOptimization Study on a Novel High-Speed Oil-Free Centrifugal Water Pump with Hydrodynamic Bearings
In aerospace fields and industrial sectors, high-speed centrifugal pumps are prevalent and in increasingly strict demand regarding characteristics such as the long life, small volume, light weight, and low noise. In this study, we present a novel high-speed centrifugal water pump with hydrodynamic bearings used to employ work fluid as lubricant. A three-dimensional numerical study of the turbulent fluid flow was carried out to predict the performance of the pump. The computational model was validated against experimental results during hydraulic tests. Additionally, the effect of the blade number on the head and efficiency of the pump was researched. The blade number of the impeller was changed from 4 to 8 and that of the stay vane was from 3 to 14. The results indicate that the blade number and the matching characteristic of the impeller and the stay vane significantly influenced the performance of the pump. The structure based on the seven-blade impeller and the six-blade stay vane had the highest efficiency (30.8%). Numerical investigations of this study may help reduce the significant cost and time of experimental work for a particular design.