Wansik Kim
Research Subjects
Wansik Kim has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Sosu Kim
Agency for Defense Development, Daejeon, Republic of Korea
6 shared publications - Jinho Jeong
Sogang University
4 shared publications - Kichul Kim
Agency for Defense Development, Daejeon, Republic of Korea
4 shared publications - Hyunji Koo
Korea Research Institute of Standards and Science (KRISS), Daejeon, South Korea
3 shared publications - Jeung Won Choi
Agency for Defense Development Daejeon Korea
3 shared publications - Jong-Min Yook
Package Research Center, Korea Electronics Technology Institute, Seongnam, Gyeonggi-do, South Korea
3 shared publications
Latest Publications
- Open Access
- 30 November 2023
- Published by Korean Institute of Electromagnetic Engineering and Science in Journal of Electromagnetic Engineering and Science
- Vol. 23 (6) , 482-489
High-Q Transformer Neutralization Technique for W-Band Dual-Band LNA Using 0.1 μm GaAs pHEMT Technology
In this study, a dual-band low-noise amplifier (LNA) was implemented by applying a transformer-based neutralization technology to the W-band. Incorporating the neutralization technique was difficult owing to performance degradation in the W-band. However, circuit performance was enhanced thanks to the layout optimization of transformer-based neutralization networks, and the improved operation was confirmed in the W-band. The neutralization technique was implemented in four stages with a 0.1-μm gallium arsenide (GaAs) pseudomorphic high-electron-mobility-transistor monolithic microwave integrated circuit LNA. The LNA showed small signal gains of 20.3 dB and 21.7 dB and noise figures of 5.0 dB and 6.4 dB (at 84 GHz and 96 GHz, respectively) while consuming 46 mW from a 1-V supply.
- 30 November 2023
- Published by Korean Institute of Electromagnetic Engineering and Science in Journal of Electromagnetic Engineering and Science
- Vol. 23 (6) , 482-489
Open AccessHigh-Q Transformer Neutralization Technique for W-Band Dual-Band LNA Using 0.1 μm GaAs pHEMT Technology
In this study, a dual-band low-noise amplifier (LNA) was implemented by applying a transformer-based neutralization technology to the W-band. Incorporating the neutralization technique was difficult owing to performance degradation in the W-band. However, circuit performance was enhanced thanks to the layout optimization of transformer-based neutralization networks, and the improved operation was confirmed in the W-band. The neutralization technique was implemented in four stages with a 0.1-μm gallium arsenide (GaAs) pseudomorphic high-electron-mobility-transistor monolithic microwave integrated circuit LNA. The LNA showed small signal gains of 20.3 dB and 21.7 dB and noise figures of 5.0 dB and 6.4 dB (at 84 GHz and 96 GHz, respectively) while consuming 46 mW from a 1-V supply.
- 22 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (11) , 1544-1547
A 131–162-GHz Wideband CMOS LNA Using Asymmetric Frequency Responses of Triple-Coupled Transformers
A $D$ -band wideband low-noise amplifier (LNA) is presented, which consists of five-cascaded differential amplifiers fabricated in a 40-nm RF CMOS process. Each stage has a common gate (CG) configuration to have low noise at the high frequencies. Triple-coupled transformers are introduced in all stages to increase gains and to make interstage matchings, which have asymmetrical frequency responses. The input and output Q factors of the transformers are tailored to achieve staggered matchings for wideband characteristics. This allows it to have a flat gain of 19.5–20.5 dB and a noise figure of 6.2–9.0 dB at 136–159 GHz. It shows a peak gain of 20.9 dB at 153 GHz and a noise figure of 6.2 dB at 148 GHz. It has a minimum ${\mathrm{IP}}_{\mathrm{1\,dB}}$ is $-$ 19.7 dBm, and occupies 0.24 mm $^{2}$ including I/O pads with the core size of 0.09 mm $^{2}$ . It consumes a total dc power of 49 mW from a 1-V supply.
- 22 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (11) , 1544-1547
A 131–162-GHz Wideband CMOS LNA Using Asymmetric Frequency Responses of Triple-Coupled Transformers
A $D$ -band wideband low-noise amplifier (LNA) is presented, which consists of five-cascaded differential amplifiers fabricated in a 40-nm RF CMOS process. Each stage has a common gate (CG) configuration to have low noise at the high frequencies. Triple-coupled transformers are introduced in all stages to increase gains and to make interstage matchings, which have asymmetrical frequency responses. The input and output Q factors of the transformers are tailored to achieve staggered matchings for wideband characteristics. This allows it to have a flat gain of 19.5–20.5 dB and a noise figure of 6.2–9.0 dB at 136–159 GHz. It shows a peak gain of 20.9 dB at 153 GHz and a noise figure of 6.2 dB at 148 GHz. It has a minimum ${\mathrm{IP}}_{\mathrm{1\,dB}}$ is $-$ 19.7 dBm, and occupies 0.24 mm $^{2}$ including I/O pads with the core size of 0.09 mm $^{2}$ . It consumes a total dc power of 49 mW from a 1-V supply.
- Open Access
- 31 January 2023
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 34 (1) , 15-24
On-Wafer Measurement of a D-Band Device
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- 31 January 2023
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 34 (1) , 15-24
Open AccessOn-Wafer Measurement of a D-Band Device
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- Open Access
- 23 December 2022
- Published by MDPI AG in Remote Sensing
- Vol. 15 (1) , 78
Non-Uniform MIMO Array Design for Radar Systems Using Multi-Channel Transceivers
Multiple-input multiple-output (MIMO) technology has recently attracted attention with regard to improving the angular resolution of small antennas such as automotive radars. If appropriately placed, the co-located transmit and receive arrays can make a large virtual aperture. This paper proposes a new method for designing arrays by adopting a structure with minimum redundancy. The proposed structure can significantly increase the virtual array aperture while keeping the transmit and receive antennas at the same size. We describe the application of the proposed method to subarray-type antennas using multi-channel transceivers, which is essential for arranging RF hardware in a small antenna operating at high frequency. Further, we present an analysis of the final beam pattern and discuss its benefits and limitations.
- 23 December 2022
- Published by MDPI AG in Remote Sensing
- Vol. 15 (1) , 78
Open AccessNon-Uniform MIMO Array Design for Radar Systems Using Multi-Channel Transceivers
Multiple-input multiple-output (MIMO) technology has recently attracted attention with regard to improving the angular resolution of small antennas such as automotive radars. If appropriately placed, the co-located transmit and receive arrays can make a large virtual aperture. This paper proposes a new method for designing arrays by adopting a structure with minimum redundancy. The proposed structure can significantly increase the virtual array aperture while keeping the transmit and receive antennas at the same size. We describe the application of the proposed method to subarray-type antennas using multi-channel transceivers, which is essential for arranging RF hardware in a small antenna operating at high frequency. Further, we present an analysis of the final beam pattern and discuss its benefits and limitations.
- Open Access
- 30 September 2022
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 33 (9) , 673-684
Waveguide Power Combiner Using E-Plane Signal Transition Structure and Resistive Septum for W-Band High Power Amplifier Applications
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- 30 September 2022
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 33 (9) , 673-684
Open AccessWaveguide Power Combiner Using E-Plane Signal Transition Structure and Resistive Septum for W-Band High Power Amplifier Applications
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- 1 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2050-2057
Embedded-IC package using Si-interposer for mmWave Applications
In this study, we optimized the interconnection of a Si-embedded IC package using a dummy IC that includes a transmission line. We also propose an improved process method to minimize the insulator effect on the chip for W-band applications. The 30-μm-thick insulator (ε r = 3.2) covering the dummy IC increases the ε eff by about 5.6%, and the reflection loss is increased by 5 dB or more. In the improved process, the insulator on the circuit area is removed by using a photosensitive material (WPR-1201). In the structure, the phase difference is improved by about 5% compared to the existing process, and there is little effect of reflection loss. The analyzed chip-to-chip (CTC) interconnection with a length of 320 μm was designed with a grounded coplanar waveguide (G-CPW), and the line width was optimized for the dielectric constant and substrate height by EM simulation. All parasitic resonances, such as cavity resonance or slot loop resonance that can occur in the embedding package were analyzed using an EM simulator and circuit model. Each resonance is removed by the appropriate positioning of via holes. As a result, the measured insertion loss of the CTC interconnection is 0.2 dB at 100 GHz without degradation of return loss and the return loss is more than 18 dB at broadband (0-100 GHz). To demonstrate the technology, an embedded IC module combining an 8x frequency multiplier and the drive amplifier was realized using the proposed process. The measured peak conversion gain was improved from 2.08 to 4.6 dB at 84 GHz in comparison to the typical embedded-IC module.
- 1 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2050-2057
Embedded-IC package using Si-interposer for mmWave Applications
In this study, we optimized the interconnection of a Si-embedded IC package using a dummy IC that includes a transmission line. We also propose an improved process method to minimize the insulator effect on the chip for W-band applications. The 30-μm-thick insulator (ε r = 3.2) covering the dummy IC increases the ε eff by about 5.6%, and the reflection loss is increased by 5 dB or more. In the improved process, the insulator on the circuit area is removed by using a photosensitive material (WPR-1201). In the structure, the phase difference is improved by about 5% compared to the existing process, and there is little effect of reflection loss. The analyzed chip-to-chip (CTC) interconnection with a length of 320 μm was designed with a grounded coplanar waveguide (G-CPW), and the line width was optimized for the dielectric constant and substrate height by EM simulation. All parasitic resonances, such as cavity resonance or slot loop resonance that can occur in the embedding package were analyzed using an EM simulator and circuit model. Each resonance is removed by the appropriate positioning of via holes. As a result, the measured insertion loss of the CTC interconnection is 0.2 dB at 100 GHz without degradation of return loss and the return loss is more than 18 dB at broadband (0-100 GHz). To demonstrate the technology, an embedded IC module combining an 8x frequency multiplier and the drive amplifier was realized using the proposed process. The measured peak conversion gain was improved from 2.08 to 4.6 dB at 84 GHz in comparison to the typical embedded-IC module.
- Open Access
- 31 March 2022
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 33 (3) , 181-189
Rectangular Waveguide-Based W-Band Eight-Way Radial Power Combiner
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- 31 March 2022
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 33 (3) , 181-189
Open AccessRectangular Waveguide-Based W-Band Eight-Way Radial Power Combiner
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- Open Access
- 28 September 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (19) , 9017
Design of W-Band GaN-on-Silicon Power Amplifier Using Low Impedance Lines
In this paper, a high-power amplifier integrated circuit (IC) in gallium-nitride (GaN) on silicon (Si) technology is presented at a W-band (75–110 GHz). In order to mitigate the losses caused by relatively high loss tangent of Si substrate compared to silicon carbide (SiC), low-impedance microstrip lines (20–30 Ω) are adopted in the impedance matching networks. They allow for the impedance transformation between 50 Ω and very low impedances of the wide-gate transistors used for high power generation. Each stage is matched to produce enough power to drive the next stage. A Lange coupler is employed to combine two three-stage common source amplifiers, providing high output power and good input/output return loss. The designed power amplifier IC was fabricated in the commercially available 60 nm GaN-on-Si high electron mobility transistor (HEMT) foundry. From on-wafer probe measurements, it exhibits the output power higher than 26.5 dBm and power added efficiency (PAE) higher than 8.5% from 88 to 93 GHz with a large-signal gain > 10.5 dB. Peak output power is measured to be 28.9 dBm with a PAE of 13.3% and a gain of 9.9 dB at 90 GHz, which corresponds to the power density of 1.94 W/mm. To the best of the authors’ knowledge, this result belongs to the highest output power and power density among the reported power amplifier ICs in GaN-on-Si HEMT technologies operating at the W-band.
- 28 September 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (19) , 9017
Open AccessDesign of W-Band GaN-on-Silicon Power Amplifier Using Low Impedance Lines
In this paper, a high-power amplifier integrated circuit (IC) in gallium-nitride (GaN) on silicon (Si) technology is presented at a W-band (75–110 GHz). In order to mitigate the losses caused by relatively high loss tangent of Si substrate compared to silicon carbide (SiC), low-impedance microstrip lines (20–30 Ω) are adopted in the impedance matching networks. They allow for the impedance transformation between 50 Ω and very low impedances of the wide-gate transistors used for high power generation. Each stage is matched to produce enough power to drive the next stage. A Lange coupler is employed to combine two three-stage common source amplifiers, providing high output power and good input/output return loss. The designed power amplifier IC was fabricated in the commercially available 60 nm GaN-on-Si high electron mobility transistor (HEMT) foundry. From on-wafer probe measurements, it exhibits the output power higher than 26.5 dBm and power added efficiency (PAE) higher than 8.5% from 88 to 93 GHz with a large-signal gain > 10.5 dB. Peak output power is measured to be 28.9 dBm with a PAE of 13.3% and a gain of 9.9 dB at 90 GHz, which corresponds to the power density of 1.94 W/mm. To the best of the authors’ knowledge, this result belongs to the highest output power and power density among the reported power amplifier ICs in GaN-on-Si HEMT technologies operating at the W-band.
- Open Access
- 30 April 2021
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 32 (4) , 353-359
W-Band 4-Way Waveguide Power Combiner Using Perpendicular Mode Conversion
- 30 April 2021
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 32 (4) , 353-359
Open AccessW-Band 4-Way Waveguide Power Combiner Using Perpendicular Mode Conversion
- Open Access
- 31 January 2021
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 32 (1) , 97-100
Measurement of Characteristics of W-Band Receiver Module
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- 31 January 2021
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 32 (1) , 97-100
Open AccessMeasurement of Characteristics of W-Band Receiver Module
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)