YYYue Yu

Yue Yu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yue Yu has a total of 9 co-authors. Here are the top co-authors by number of shared publications:

  • Jianli Li

    The State Key Laboratory of Refractories and Metallurgy Wuhan University of Science and Technology Wuhan 430081 China

    6 shared publications
  • Hangyu Zhu

    State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan, P.R. China

    3 shared publications
  • Qiang Zeng

    The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan 430081, China

    3 shared publications
  • Cao Jia

    The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan 430081, China

    1 shared publication
  • Jiajun Jiang

    Hubei Provincial Key Laboratory for New Processes of Ironmaking and Steelmaking, Wuhan University of Science and Technology, Wuhan 430081, China

    1 shared publication
  • Mengxu Zhang

    The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan 430081, China

    1 shared publication

Latest Publications

  • Open Access

    Dissolution Behavior of Lime with Different Properties into Converter Slag

    by Mengxu Zhang, Jianli Li, Cao Jia, Yue Yu

    China’s 2022 crude steel production soared to an impressive 1.018 billion tons, and steel slag constituted approximately 10% to 15% of this massive output. However, a notable hindrance to the comprehensive utilization of steel slag arises from the fact that it contains 10% to 20% of free calcium oxide (f-CaO), resulting in volume instability. To address this challenge, our study delved into the dynamic transformation of the interface between lime and slag, as well as the fluctuations in the dissolution rate of lime. An Electron Probe Micro Analyzer, equipped with an energy-dispersive spectrometer, was employed for the analysis. Our findings revealed that the configuration of the reaction interface between quicklime and slag underwent alterations throughout various phases of converter smelting. At a temperature of 1400 °C, several significant transformations occurred, including the formation of a CaO-FeO solid solution, (Ca, Mg, Fe) olivine, and low-melting point (Ca, Mg) silicate minerals. With the gradual reduction in FeO content, a robust and high-melting 2CaO·SiO2 layer emerged, generated through the interaction between CaO and (Ca, Mg, Fe) olivine. Furthermore, for lime with a particle size of 20 mm and a calcination rate of 0%, the thickest layer of 2CaO·SiO2 was observed after 120 s of dissolution in slag A2 at 1400 °C. Overall, the dissolution rates of lime with different particle sizes in slag A1 to A4 showed a gradual increase. On the other hand, the dissolution rates of lime with different calcination rates in slag A1 to A4 exhibited an initial increase, followed by a decrease, and then another increase. The formation of a high-melting point and continuous dense 2CaO·SiO2 layer during the dissolution process hindered the mass transfer between lime and slag.


  • Open Access

    Effect of Cr2O3 on Physicochemical Properties of CaO-SiO2-FetO Slags during BOF Smelting Process of Chromium-Bearing Iron

    by Shannan Li, Jianli Li, Yue Yu, Hangyu Zhu

    The productivity of basic-oxygen-furnace (BOF) smelting process is directly affected by the slag-forming speed during the initial stage of converter. Therefore, it is essential to study the effect of different Cr2O3 content on the physicochemical properties of the primary slag in the smelting process of chromium-bearing semi-steel. In this work, Factsage8.1 software, X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and a high-temperature melting point tester were used to study the effects of different Cr2O3 content on the melting temperature, solidification behavior, mineral composition, and other physicochemical properties of the CaO-SiO2-FetO system. The results showed that the melting temperature of slag samples increased from 1223 °C to 1354 °C as Cr2O3 increased from 0 wt% to 9.09 wt%. With the increase of Cr2O3, the content of CaFeSi2O6 decreased. Moreover, due to the addition of Cr2O3, the chromium-bearing spinel solid solution (Fe(Fe,Cr)2O4) began to form in the slag. Furthermore, Cr2O3 promoted the increase in the volume of free solid particles in the slag, resulting in an increase in slag viscosity. All in all, the increase of Cr2O3 content in the CaO-SiO2-FetO system will adversely affect the semi-steel steelmaking process.


  • Open Access

    Occurrence and Leaching Behavior of Chromium in Synthetic Stainless Steel Slag Containing FetO

    by Qiang Zeng, Jianli Li, Yue Yu, Hangyu Zhu

    Stainless steel slag has been applied to other silicate materials due to its CaO-SiO2-based system. This is done to improve the utilization rate of stainless steel slag and apply it more safely. This paper investigated the occurrence of chromium in synthetic stainless steel slag containing FetO and its leaching behavior. The phase composition of the equilibrium reaction was calculated by FactSage 7.3 Equlib module. XRD, SEM-EDS and IPP 6.0 were used to investigate the phase compositions, microstructure and count the size of spinel crystals. The results indicate that the increase of Fe2O3 content can promote the precipitation of spinel phases and effectively inhibit the formation and precipitation of α-C2S in a CaO-SiO2-MgO-Cr2O3-Al2O3-FeO system. Fe2O3 contents increased from 2 wt% to 12 wt%, and the crystal size increased from 4.01 μm to 6.06 μm, with a growing rate of 51.12%. The results of SEM line scanning show the Cr-rich center and Fe-rich edge structure of the spinel phase. Comparing the TRGS 613 standard with the HJ/T 299-2007 standard, the leaching of Cr6+ in the FetO samples is far lower than the standards’ limit, and the minimum concentration is 0.00791 mg/L in 12 wt% Fe2O3 samples.


  • Open Access

    Effect of Basicity on the Sulfur Precipitation and Occurrence State in Kambara Reactor Desulfurization Slag

    by Renlin Zhu, Jianli Li, Jiajun Jiang, Yue Yu, Hangyu Zhu

    Kambara Reactor (KR) desulfurization slag used as slag-making material for converter smelting can promote early slag melting in the initial stage and improve the efficiency of dephosphorization. However, its direct utilization as a slagging material can increase the sulfur content in molten steel since KR desulfurization slag contains 1~2.5% sulfur. Therefore, this research focuses on the effect of basicity on the precipitation behavior and occurrence state of sulfur in KR desulfurization slag in order to provide an academic reference for the subsequent removal of sulfur from slag through an oxidizing atmosphere. The solidification process of slag was simulated by the Factsage8.0. The slag samples were analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM), and the amount of CaS grains was analyzed using Image-ProPlus6.0 software. The thermodynamic calculation showed that the crystallization temperature of CaS in the molten slag gradually decreased with the increase in basicity, and the CaS crystals in the molten slag mainly existed in the matrix phase and at the silicate grain boundaries. A large number of CaS grains were precipitated along the silicate grain boundary in low-basicity (R = 2.5 and 3.0) slags and fewer CaS grains were precipitated along the silicate grain boundary, while the CaS grain density in the matrix phase was higher in the high-basicity (R = 3.5, 4.0, 4.5) slag. With the increase in basicity, the number of CaS grains gradually decreased, and the CaS grain sizes in slag sample increased gradually. The sulfur in the synthetic slag was in the form of CaS crystals and the amorphous phase, and the content of amorphous sulfur gradually increased with increasing basicity.


  • Open Access

    Analysis of Micro-Segregation of Solute Elements on the Central Cracking of Continuously Cast Bloom

    by Qiang Zeng, Chao Xiao, Jianli Li

    On the basis of the Brody–Flemings model and modified Voller–Beckermann model, an analytical model of micro-segregation is established by considering the actual solidification cooling conditions of bloom. According to the developed model, the interdendritic solute distribution at the origin of the cracking gap is obtained. It is found that both phosphorus and sulfur have quite severe segregation, but both carbon and manganese have slight segregation; these results agree well with the semiquantitative analysis results of the scanning electron microscope (SEM). At the same time, the interdendritic segregation leads to an enhanced increase in the temperature range of crack formation; correspondingly, the possibility of cracking significantly increases and, thus, element segregation is the internal cause of crack formation. On the other hand, taking into account heat transfer, phase transformation, and metallurgical pressure, the strain of the solid shell is revealed through finite element software. When the solid shell thickness is equal to the distance of 90 mm between the opening point of the crack and the inner arc side, the tensile strain of the solid front is much bigger than the critical strain, which meets the external cause of crack formation; therefore, reasons for the cracking of blooms are successfully found.


  • Open Access

    Experimental Study on Precipitation Behavior of Spinels in Stainless Steel-Making Slag under Heating Treatment

    by Jianli Li, Qiqiang Mou, Qiang Zeng, Yue Yu

    The stability of chromium in stainless steel slag has a positive correlation with spinel particle size and a negative correlation with the calcium content of the spinel. The effect of heating time on the precipitation of spinel crystals in the CaO-SiO2-MgO-Al2O3-Cr2O3-FeO system was investigated in the laboratory. Scanning electron microscopy with energy-dispersive and X-ray diffraction were adopted to observe the microstructure, test the chemical composition, and determine the mineral phases of synthetic slags, and FactSage7.1 was applied to calculate the crystallization process of the molten slag. The results showed that the particle size of the spinel crystals increased from 9.42 to 10.73 μm, the calcium content in the spinel crystals decreased from 1.38 at% to 0.78 at%, and the content of chromium in the spinel crystal increased from 16.55 at% to 22.78 at% with an increase in the heating time from 0 min to 120 min at 1450 °C. Furthermore, the species of spinel minerals remained constant. Therefore, an extension in the heating time is beneficial for improving the stability of chromium in stainless steel slag.