Mehmet Gürsoy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Mehmet Gürsoy has a total of 90 co-authors. Here are the top co-authors by number of shared publications:
- Mustafa Karaman
Konya Teknik Üniversitesi
18 shared publications Mustafa Karaman
17 shared publications- Kurtuluş Yılmaz
Konya Teknik Üniversitesi
7 shared publications - Woei Jye Lau
Advanced Membrane Technology Research Centre (AMTEC), Faculty of Chemical and Energy Engineering, Universiti Teknologi Malaysia, Johor Bahru 81310, Johor, Malaysia
6 shared publications Ahmad Fauzi Ismail
5 shared publicationsHüseyin Şakalak
Advanced Materials and Nanotechnology Department, Selcuk University, Konya 42075, Turkey
5 shared publications
Latest Publications
- 30 March 2026
- Published by Erzincan Universitesi Fen Bilimleri Ensitusu Dergisi in Erzincan Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 19 (1) , 253-267
Investigation of Fog Harvesting Performance of Functional Thin Film-Coated 3D Surfaces
Access to clean water is one of the major global challenges due to the depletion of natural freshwater reserves, exacerbated by global warming and increasing world population. Reverse osmosis and desalination methods are commonly used for clean water production; however, these methods have high investment and energy costs, limiting their widespread application. In recent years, atmospheric water collection, using fog, has emerged as an energy-efficient, low-cost, and environmentally friendly alternative method. However, traditional fog harvesting nets have low efficiency, prompting increasing interest in developing materials that can collect fog at higher yields. In this study, 3D printing was used to create surfaces with various topographies, which were then coated with hydrophilic polyacrylic acid (PAA) and hydrophobic polyhexafluorobutyl acrylate (PHFBA) thin films in a single step, utilizing the environmentally friendly plasma enhanced chemical vapor deposition (PECVD) technique. Additionally, surfaces exhibiting both hydrophilic and hydrophobic properties were designed and fabricated. The chemical structure, topographical features, and wettability characteristics of the coated surfaces were thoroughly characterized. A total of 22 samples with different surface structures and wettability properties were produced. Fog harvesting experiments revealed that, compared to the control surface, the surface designs achieved up to a 270% increase in fog harvesting efficiency. The results demonstrate that surface topography and wettability are key factors influencing fog harvesting performance.
- 30 March 2026
- Published by Erzincan Universitesi Fen Bilimleri Ensitusu Dergisi in Erzincan Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 19 (1) , 253-267
Investigation of Fog Harvesting Performance of Functional Thin Film-Coated 3D Surfaces
Access to clean water is one of the major global challenges due to the depletion of natural freshwater reserves, exacerbated by global warming and increasing world population. Reverse osmosis and desalination methods are commonly used for clean water production; however, these methods have high investment and energy costs, limiting their widespread application. In recent years, atmospheric water collection, using fog, has emerged as an energy-efficient, low-cost, and environmentally friendly alternative method. However, traditional fog harvesting nets have low efficiency, prompting increasing interest in developing materials that can collect fog at higher yields. In this study, 3D printing was used to create surfaces with various topographies, which were then coated with hydrophilic polyacrylic acid (PAA) and hydrophobic polyhexafluorobutyl acrylate (PHFBA) thin films in a single step, utilizing the environmentally friendly plasma enhanced chemical vapor deposition (PECVD) technique. Additionally, surfaces exhibiting both hydrophilic and hydrophobic properties were designed and fabricated. The chemical structure, topographical features, and wettability characteristics of the coated surfaces were thoroughly characterized. A total of 22 samples with different surface structures and wettability properties were produced. Fog harvesting experiments revealed that, compared to the control surface, the surface designs achieved up to a 270% increase in fog harvesting efficiency. The results demonstrate that surface topography and wettability are key factors influencing fog harvesting performance.
- Open Access
Raster Orientation Effects on the Adhesion of iCVD-Deposited PSA Thin Films on FDM-Printed PLA
The adhesion performance of pressure-sensitive adhesive (PSA) thin films on additively manufactured polymers is strongly governed by surface anisotropy induced during printing. In this study, PSA thin films based on 2-ethylhexyl acrylate (EHA) and acrylic acid (AA) were deposited by initiated chemical vapor deposition (iCVD) onto fused deposition modeling (FDM) printed PLA substrates with different raster orientations (0°, 30°, 60°, and 90°). The deposited films exhibited high optical transparency on glass, and thicknesses consistent with the targeted deposition. Adhesion performance was evaluated using tensile and three-point bending tests, revealing a strong dependence on raster orientation. The 0° raster orientation yielded the highest shear adhesion strengths, reaching 12.03 N/cm2 under tensile loading and 4.59 N/cm2 under bending, along with the largest failure displacements. In contrast, specimens printed at 90° exhibited an approximately 47% reduction in tensile shear adhesion strength and limited deformation prior to failure. SEM analysis showed that raster alignment parallel to the loading direction promoted extensive adhesive deformation and PSA fibrillation, whereas higher raster angles resulted in predominantly interfacial debonding. These results demonstrate that raster orientation is a critical design parameter for tuning PSA adhesion on FDM-printed PLA substrates without modifying adhesive chemistry.
Open AccessRaster Orientation Effects on the Adhesion of iCVD-Deposited PSA Thin Films on FDM-Printed PLA
The adhesion performance of pressure-sensitive adhesive (PSA) thin films on additively manufactured polymers is strongly governed by surface anisotropy induced during printing. In this study, PSA thin films based on 2-ethylhexyl acrylate (EHA) and acrylic acid (AA) were deposited by initiated chemical vapor deposition (iCVD) onto fused deposition modeling (FDM) printed PLA substrates with different raster orientations (0°, 30°, 60°, and 90°). The deposited films exhibited high optical transparency on glass, and thicknesses consistent with the targeted deposition. Adhesion performance was evaluated using tensile and three-point bending tests, revealing a strong dependence on raster orientation. The 0° raster orientation yielded the highest shear adhesion strengths, reaching 12.03 N/cm2 under tensile loading and 4.59 N/cm2 under bending, along with the largest failure displacements. In contrast, specimens printed at 90° exhibited an approximately 47% reduction in tensile shear adhesion strength and limited deformation prior to failure. SEM analysis showed that raster alignment parallel to the loading direction promoted extensive adhesive deformation and PSA fibrillation, whereas higher raster angles resulted in predominantly interfacial debonding. These results demonstrate that raster orientation is a critical design parameter for tuning PSA adhesion on FDM-printed PLA substrates without modifying adhesive chemistry.
- 2 September 2025
- Published by Elsevier in Applied Surface Science
- Vol. 714
Pressure-sensitive adhesive thin films with tailored properties via solvent-free plasma deposition of EHA/AA copolymers
- 2 September 2025
- Published by Elsevier in Applied Surface Science
- Vol. 714
Pressure-sensitive adhesive thin films with tailored properties via solvent-free plasma deposition of EHA/AA copolymers
- Open Access
Large-Area Deposition of Hydrophobic Poly(hexafluorobutyl Acrylate) Thin Films on Wetting-Sensitive and Flexible Substrates via Plasma-Enhanced Chemical Vapor Deposition
In this study, hydrophobic poly(hexafluorobutyl acrylate) (PHFBA) thin films were successfully deposited over a large area of 25 × 50 cm using plasma-enhanced chemical vapor deposition (PECVD). Key parameters, including plasma power and the distance between the plasma antenna and the substrate, were optimized to achieve the highest deposition rate while ensuring uniformity and defect-free coatings. The optimal conditions were determined as 5 W plasma power and a 9 cm antenna–substrate distance, yielding a maximum deposition rate of 11.3 nm/min. PHFBA’s low fluorine content makes it a more environmentally and biologically friendly alternative compared to heavily fluorinated polymers, addressing concerns about toxicity and environmental impact. The coatings were applied to a flexible and wetting-sensitive paper towel substrate, which was successfully coated without any visible defects. The contact angle measurements confirmed the hydrophobic nature of the films, with a maximum water contact angle of 131.9° after the deposition of PHFBA. This study highlights the potential of PECVD as an efficient and scalable method for producing hydrophobic coatings, combining high-performance properties with improved environmental considerations. The results not only validate PECVD as a scalable and precise method for thin film fabrication but also open new possibilities for its use in applications requiring durable and functional surface modifications.
Open AccessLarge-Area Deposition of Hydrophobic Poly(hexafluorobutyl Acrylate) Thin Films on Wetting-Sensitive and Flexible Substrates via Plasma-Enhanced Chemical Vapor Deposition
In this study, hydrophobic poly(hexafluorobutyl acrylate) (PHFBA) thin films were successfully deposited over a large area of 25 × 50 cm using plasma-enhanced chemical vapor deposition (PECVD). Key parameters, including plasma power and the distance between the plasma antenna and the substrate, were optimized to achieve the highest deposition rate while ensuring uniformity and defect-free coatings. The optimal conditions were determined as 5 W plasma power and a 9 cm antenna–substrate distance, yielding a maximum deposition rate of 11.3 nm/min. PHFBA’s low fluorine content makes it a more environmentally and biologically friendly alternative compared to heavily fluorinated polymers, addressing concerns about toxicity and environmental impact. The coatings were applied to a flexible and wetting-sensitive paper towel substrate, which was successfully coated without any visible defects. The contact angle measurements confirmed the hydrophobic nature of the films, with a maximum water contact angle of 131.9° after the deposition of PHFBA. This study highlights the potential of PECVD as an efficient and scalable method for producing hydrophobic coatings, combining high-performance properties with improved environmental considerations. The results not only validate PECVD as a scalable and precise method for thin film fabrication but also open new possibilities for its use in applications requiring durable and functional surface modifications.
- Open Access
- 1 September 2024
- Published by Konya Muhendislik Bilimleri Dergisi in Konya Journal of Engineering Sciences
- Vol. 12 (3) , 586-595
INITIATED CHEMICAL VAPOR DEPOSITION (iCVD) OF POLY(ACRYLIC ACID): A COMPARISON BETWEEN CONTINUOUS AND CLOSED-BATCH iCVD APPROACHES
In this study, poly(acrylic acid) (PAA) thin films were deposited on silicon wafer and glass surfaces by initiated chemical vapor deposition (iCVD) method using di-tert-butyl peroxide (TBPO) as the initiator and acrylic acid (AA) as the monomer. During iCVD, two different precursor feeding approaches, namely continuous and closed-batch, were employed. The effects of substrate temperature and the precursor feeding approaches on the deposition rates and surface morphology of the films were investigated. The highest deposition rates for the continuous and closed-batch iCVD approaches were found as 26.1 nm/min and 18.6 nm/min, respectively, at a substrate temperature of 15 °C. FTIR analysis of the films deposited by both approaches indicated high structural retention of the monomer during the polymerization. AFM results indicated that, PAA thin films possessed low RMS roughness values of 2.76 nm and 1.84 nm using continuous and closed-batch iCVD, respectively. Due to the slightly higher surface roughness of the film deposited under continuous iCVD, that film exhibited a lower water contact angle of 16.1° than the film deposited in closed-batch iCVD. In terms of monomer utilization ratio, closed-batch system was found to be more effective, which may help to minimize the carbon footprint of iCVD process.
- 1 September 2024
- Published by Konya Muhendislik Bilimleri Dergisi in Konya Journal of Engineering Sciences
- Vol. 12 (3) , 586-595
Open AccessINITIATED CHEMICAL VAPOR DEPOSITION (iCVD) OF POLY(ACRYLIC ACID): A COMPARISON BETWEEN CONTINUOUS AND CLOSED-BATCH iCVD APPROACHES
In this study, poly(acrylic acid) (PAA) thin films were deposited on silicon wafer and glass surfaces by initiated chemical vapor deposition (iCVD) method using di-tert-butyl peroxide (TBPO) as the initiator and acrylic acid (AA) as the monomer. During iCVD, two different precursor feeding approaches, namely continuous and closed-batch, were employed. The effects of substrate temperature and the precursor feeding approaches on the deposition rates and surface morphology of the films were investigated. The highest deposition rates for the continuous and closed-batch iCVD approaches were found as 26.1 nm/min and 18.6 nm/min, respectively, at a substrate temperature of 15 °C. FTIR analysis of the films deposited by both approaches indicated high structural retention of the monomer during the polymerization. AFM results indicated that, PAA thin films possessed low RMS roughness values of 2.76 nm and 1.84 nm using continuous and closed-batch iCVD, respectively. Due to the slightly higher surface roughness of the film deposited under continuous iCVD, that film exhibited a lower water contact angle of 16.1° than the film deposited in closed-batch iCVD. In terms of monomer utilization ratio, closed-batch system was found to be more effective, which may help to minimize the carbon footprint of iCVD process.
- 22 August 2024
- Published by Elsevier in Progress in Organic Coatings
- Vol. 196
Synthesis and characterization of stretchable isoprene-acrylic acid copolymer thin films
- 22 August 2024
- Published by Elsevier in Progress in Organic Coatings
- Vol. 196
Synthesis and characterization of stretchable isoprene-acrylic acid copolymer thin films
- 26 June 2024
- Published by Elsevier in Surfaces and Interfaces
- Vol. 51
Anti-fogging properties of amphiphilic copolymer films deposited by chemical vapor deposition (CVD)
- 26 June 2024
- Published by Elsevier in Surfaces and Interfaces
- Vol. 51
Anti-fogging properties of amphiphilic copolymer films deposited by chemical vapor deposition (CVD)
- Open Access
Fabrication of pH-Responsive PDPAEMA Thin Film Using a One-Step Environmentally Friendly Plasma Enhanced Chemical Vapor Deposition
In recent years, there has been growing interest in pH-responsive polymers. Polymers with ionizable tertiary amine groups, which have the potential to be used in many critical application areas due to their pKa values, have an important place in pH-responsive polymers. In this study, poly(2-Diisopropyl aminoethyl methacrylate) (PDPAEMA) thin films were coated on various substrates such as glass, fabric, and silicon wafer using a one-step environmentally friendly plasma enhanced chemical vapor deposition (PECVD) method. The effects of typical PECVD plasma processing parameters such as substrate temperature, plasma power, and reactor pressure on the deposition rate were studied. The highest deposition rate was obtained at a substrate temperature of 40 °C, a reactor pressure of 300 mtorr, and a plasma power of 60 W. The apparent activation energy was found to be 17.56 kJ/mol. Based on the results of this study, uniform film thickness and surface roughness were observed in a large area. The PDPAEMA thin film was exposed to successive acid/base cycles. The results showed that the pH sensitivity of the thin film produced by the PECVD method is permanent and reversible.
Open AccessFabrication of pH-Responsive PDPAEMA Thin Film Using a One-Step Environmentally Friendly Plasma Enhanced Chemical Vapor Deposition
In recent years, there has been growing interest in pH-responsive polymers. Polymers with ionizable tertiary amine groups, which have the potential to be used in many critical application areas due to their pKa values, have an important place in pH-responsive polymers. In this study, poly(2-Diisopropyl aminoethyl methacrylate) (PDPAEMA) thin films were coated on various substrates such as glass, fabric, and silicon wafer using a one-step environmentally friendly plasma enhanced chemical vapor deposition (PECVD) method. The effects of typical PECVD plasma processing parameters such as substrate temperature, plasma power, and reactor pressure on the deposition rate were studied. The highest deposition rate was obtained at a substrate temperature of 40 °C, a reactor pressure of 300 mtorr, and a plasma power of 60 W. The apparent activation energy was found to be 17.56 kJ/mol. Based on the results of this study, uniform film thickness and surface roughness were observed in a large area. The PDPAEMA thin film was exposed to successive acid/base cycles. The results showed that the pH sensitivity of the thin film produced by the PECVD method is permanent and reversible.
- Open Access
- 14 February 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (8) , 8810-8817
Environmentally Friendly and All-Dry Hydrophobic Patterning of Graphene Oxide for Fog Harvesting
This study examines the fog-harvesting ability of graphene oxide surfaces patterned by hydrophobic domains. The samples were prepared from graphene deposited using low pressure chemical vapor deposition, which was later plasma oxidized to obtain hydrophilic graphene oxide (GO) surfaces. Hydrophobic domains on GO surfaces were formed by initiated CVD (iCVD) of a low-surface-energy poly(perfluorodecyl alkylate) (PPFDA) polymer. Hence, patterned surfaces with hydrophobic/hydrophilic contrast were produced with ease in an all-dry manner. The structures of the as-deposited graphene and PPFDA films were characterized using Raman and Fourier transform infrared spectrophotometer analyses, respectively. The fog harvesting performance of the samples was measured using the fog generated by a nebulizer, in which the average diameter of the fog droplets is comparable to meteorological fog. According to the fog harvesting experiment results, 100 cm2 of the as-patterned surface can collect fog up to 2.5 L in 10 h in a foggy environment. Hence, hydrophilic/hydrophobic patterned surfaces in this study can be considered as promising fog harvesting materials. Both CVD techniques used in the production of hydrophilic/hydrophobic patterned surfaces can be easily applied to the production of large-scale materials.
- 14 February 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (8) , 8810-8817
Open AccessEnvironmentally Friendly and All-Dry Hydrophobic Patterning of Graphene Oxide for Fog Harvesting
This study examines the fog-harvesting ability of graphene oxide surfaces patterned by hydrophobic domains. The samples were prepared from graphene deposited using low pressure chemical vapor deposition, which was later plasma oxidized to obtain hydrophilic graphene oxide (GO) surfaces. Hydrophobic domains on GO surfaces were formed by initiated CVD (iCVD) of a low-surface-energy poly(perfluorodecyl alkylate) (PPFDA) polymer. Hence, patterned surfaces with hydrophobic/hydrophilic contrast were produced with ease in an all-dry manner. The structures of the as-deposited graphene and PPFDA films were characterized using Raman and Fourier transform infrared spectrophotometer analyses, respectively. The fog harvesting performance of the samples was measured using the fog generated by a nebulizer, in which the average diameter of the fog droplets is comparable to meteorological fog. According to the fog harvesting experiment results, 100 cm2 of the as-patterned surface can collect fog up to 2.5 L in 10 h in a foggy environment. Hence, hydrophilic/hydrophobic patterned surfaces in this study can be considered as promising fog harvesting materials. Both CVD techniques used in the production of hydrophilic/hydrophobic patterned surfaces can be easily applied to the production of large-scale materials.