ZQZuoqin Qian

Zuoqin Qian

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zuoqin Qian has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Finite Element Analysis of Thermal and Stress Fields of Diesel Engine Piston with GZO/YSZ Dual-Ceramic Layer Thermal Barrier Coating

    by Zuoqin Qian, Yuchong Hu, Chunguang Fei, Zihao Shu, Siwei Zhu, Yuxuan Du

    Thermal barrier coating can effectively reduce the temperature of engine piston substrates. However, traditional YSZ coating materials are prone to sintering under high-temperature conditions, resulting in coating failure. To address this issue, finite element simulation of a type of new coating was conducted. Gd2Zr2O7 (GZO), a material with strong anti-sintering properties, was selected as a potential candidate for the design of a dual-ceramic layer thermal barrier coating. A GZO/YSZ-coated piston of a diesel engine was designed, and its mechanical/thermal behavior was simulated by a finite element model. A piston surface temperature experiment was conducted to validate the finite element model. The temperature and the thermal stress of the GZO/YSZ dual-ceramic layer coated piston were analyzed by finite element simulation software ANSYS 2023. The results showed that the GZO/YSZ dual-ceramic layer coating effectively reduced the substrate temperature and showed potential for improving the thermal efficiency of the engine. However, due to the properties of GZO and the structure of the coating, the surface stress of the GZO/YSZ dual-ceramic layer coating was relatively high, requiring further studies to verify its reliability.


  • Open Access

    Experimental Study of a Bionic Porous Media Evaporative Radiator Inspired by Leaf Transpiration: Exploring Energy Change Processes

    by Zuoqin Qian, Xinyu Wang, Jie Ren, Qiang Wang, Lumei Zhao

    The performance of photovoltaic (PV) cells is significantly influenced by their operating temperature. While conventional active cooling methods are limited by economic feasibility, passive cooling strategies often face challenges related to insufficient heat dissipation capacity. This study presents a bio-inspired evaporative heat sink, modeled on the transpiration and water transport mechanisms of plant leaves, which leverages porous media flow and heat transfer. The device uses capillary pressure, generated through the evaporation of the cooling medium under sunlight, to maintain continuous coolant flow, thereby achieving effective cooling. An experimental setup was developed to validate the device’s performance under a heat flux density of 1200 W/m2, resulting in a maximum temperature reduction of 5 °C. This study also investigated the effects of porous medium thickness and porosity on thermal performance. The results showed that increasing the thickness of the porous medium reduces cooling efficiency due to reduced fluid flow. In contrast, the effect of porosity was temperature-dependent: at evaporation temperatures below 67 °C, a porosity of 0.4 provided better cooling, while at higher temperatures, a porosity of 0.6 was more effective. These findings confirm the feasibility of the proposed device and provide valuable insights into optimizing porous media properties to enhance the passive cooling of photovoltaic cells.


  • Open Access

    Optimization of Twist Winglets–Cross-Section Twist Tape in Heat Exchangers Using Machine Learning and Non-Dominated Sorting Genetic Algorithm II Technique

    by Qiqi Cao, Zuoqin Qian, Qiang Wang

    This research delves into the impact of Twist Winglets–Cross-Section Twist Tape (TWs-CSTT) structures within heat exchangers on thermal performance. Utilizing Computational Fluid Dynamics (CFD) and machine learning methodologies, optimal geometrical parameters for the TWs-CSTT configuration were examined. The outcomes demonstrate that fluid undergoing a rotational motion within tubes featuring this structure leads to more effective secondary flows, intensified mixing, and improved thermal boundary layer disturbance. Moreover, by integrating machine learning with multi-objective optimization techniques, the performance of heat exchangers can be accurately predicted and optimized, facilitating enhanced heat exchanger design. Through the application of the multi-objective optimization algorithm Non-dominated Sorting Genetic Algorithm II (NSGA-II), the ideal configurations for TWs-CSTT were ascertained: L1 is the cross-sectional length of the Twisted Wings, L2 is the radius of the Central Straight Twisted, and P is the pitch. P = 50.699 mm, L1 = 4.3282 mm, L2 = 4.9736 mm for the Gaussian Process Regression (GPR) model; P = 50.864 mm, L1 = 4.4961 mm, L2 = 4.9992 mm for the LR model; and P = 50.699 mm, L1 = 4.3282 mm, L2 = 4.9736 mm for the Support Vector Regression (SVR) model, aiming to maximize heat exchange efficiency while minimizing friction losses. This study proposes a novel methodological approach to heat exchanger design, leveraging CFD and machine learning technologies to enhance energy efficiency and performance.


  • Open Access

    Exergoeconomic Analysis and Optimization of a Biomass Integrated Gasification Combined Cycle Based on Externally Fired Gas Turbine, Steam Rankine Cycle, Organic Rankine Cycle, and Absorption Refrigeration Cycle

    by Jie Ren, Chen Xu, Zuoqin Qian, Weilong Huang, Baolin Wang

    Adopting biomass energy as an alternative to fossil fuels for electricity production presents a viable strategy to address the prevailing energy deficits and environmental concerns, although it faces challenges related to suboptimal energy efficiency levels. This study introduces a novel combined cooling and power (CCP) system, incorporating an externally fired gas turbine (EFGT), steam Rankine cycle (SRC), absorption refrigeration cycle (ARC), and organic Rankine cycle (ORC), aimed at boosting the efficiency of biomass integrated gasification combined cycle systems. Through the development of mathematical models, this research evaluates the system’s performance from both thermodynamic and exergoeconomic perspectives. Results show that the system could achieve the thermal efficiency, exergy efficiency, and levelized cost of exergy (LCOE) of 70.67%, 39.13%, and 11.67 USD/GJ, respectively. The analysis identifies the combustion chamber of the EFGT as the component with the highest rate of exergy destruction. Further analysis on parameters indicates that improvements in thermodynamic performance are achievable with increased air compressor pressure ratio and gas turbine inlet temperature, or reduced pinch point temperature difference, while the LCOE can be minimized through adjustments in these parameters. Optimized operation conditions demonstrate a potential 5.7% reduction in LCOE at the expense of a 2.5% decrease in exergy efficiency when compared to the baseline scenario.


  • Open Access

    Investigation of a Biomass-Driven Cogeneration System Integrated with an Externally Fired Gas Turbine, Organic Rankine Cycle, and Absorption Refrigeration Cycle: Thermodynamic and Exergoeconomic Analyses and Optimization

    by Jie Ren, Zuoqin Qian, Xinyu Wang, Weilong Huang, Baolin Wang

    The utilization of biomass for multi-generation systems is garnering significant interest due to its potential in conserving primary energy and mitigating greenhouse gas emissions. However, enhancing its energy efficiency remains a critical challenge. This study introduces an innovative cogeneration system that combines biomass gasification with an externally fired gas turbine, organic Rankine cycle, and absorption refrigeration cycle. It undergoes thorough thermodynamic and exergoeconomic evaluations, with a dual-objective optimization conducted to identify the optimal operational conditions that achieve the highest exergy efficiency while minimizing product cost. The findings reveal that, in the base case, the thermal efficiency, exergy efficiency, and sum unit cost of the product (SUCP) of the system are 66.36%, 32.04%, and 8.71 USD/GJ, respectively. A parametric study illustrates that elevating the air compressor pressure ratio or the temperature difference at the cold end enhances thermal efficiency but reduces exergy efficiency. Additionally, the lowest unit cost of the product is attainable by optimizing the gas turbine inlet temperature. The performance of the system shows negligible sensitivity to the turbine inlet pressure of a bottoming organic Rankine cycle. Finally, optimization demonstrates a 9.7% increase in exergy efficiency and a 1.8% rise in the SUCP compared to the baseline scenario. The study suggests integrating with other energy sources for diversified product outputs and conducting environmental analyses in future research.


  • Open Access

    Multi-Output Regression Algorithm-Based Non-Dominated Sorting Genetic Algorithm II Optimization for L-Shaped Twisted Tape Insertions in Circular Heat Exchange Tubes

    by Shijie Li, Zuoqin Qian, Ji Liu

    In this study, an optimization method using various multi-output regression models as model proxies within the NSGA-II framework was applied to determine the geometric parameters (P, W, D) of L-shaped twisted tape inserts for achieving the optimal overall heat transfer performance in a circular heat exchange tube. Herein, 4 multi-output regression models, namely, MOLR, MOSVR, MOGPR, and BPNN, were selected as proxy models and trained on a dataset containing 74 groups of data. The training results indicated that the MOGPR model, balancing high accuracy and low error conditions, exhibited moderate training times among the four algorithms. BPNN showed a comparatively lower comprehensive training effect, obtaining training accuracy close to that of the MOGPR algorithm but with approximately twice the training time. The worst fitting performance was gained with the MOSVR algorithm. Due to its fitting performance, the MOSVR algorithm was excluded from the subsequent NSGA-II model proxy. Through multi-objective optimization with NSGA-II, the optimal structural dimensions for three sets of L-shaped twisted tape inserts were obtained to achieve the best overall heat transfer efficiency within the tube.


  • Open Access

    Investigation of Heat Transfer Performance in Deionized Water–Ethylene Glycol Binary Mixtures during Nucleate Pool Boiling

    by Chen Xu, Jie Ren, Zuoqin Qian, Lumei Zhao

    Pool boiling heat transfer is recognized as an exceptionally effective method, widely applied across various industries. The adoption of non-azeotropic binary mixtures aligns with the environmental objectives of modern industrial development and enhances the coefficient of performance (COP) in numerous systems. Therefore, investigating the boiling heat transfer characteristics of these mixtures is crucial to improving their industrial usability. In this study, mixtures of ethylene glycol and deionized water (EG/DW) in varying concentrations were chosen as the working fluids. A comprehensive experimental setup was developed, followed by a series of experiments to assess their pool boiling performance. Simultaneously, the thermophysical parameters of these mixtures underwent detailed examination and analysis. The research revealed that the concentration of EG in the mixture markedly affects its thermal properties and temperature glide, both of which are crucial in influencing the heat transfer coefficient. Additionally, six established heat transfer coefficient prediction correlations, primarily designed for pure fluids, have been employed. However, their application to non-azeotropic mixtures under experimental conditions revealed significant deviations. To address this issue, the present study modified existing correlations with the temperature slip characteristics of non-azeotropic mixtures. This process involved recalibrating the wall superheat values in the correlations to reflect the local temperature differential at the boiling point, thereby customizing them for application to non-azeotropic mixtures. The modified correlations highlighted the unique behaviors of non-azeotropic mixtures in boiling heat transfer, demonstrating improved compatibility with these mixtures in a deviation within a permissible 20% range compared with experimental results.


  • Open Access

    Investigation of Heat Transfer Performance in Deionized Water-Ethylene Glycol Binary Mixtures during Nucleate Pool Boiling

    by Chen Xu, Jie Ren, Zuoqin Qian, Lumei Zhao

    Pool boiling heat transfer is recognized as one of the most effective heat transfer methods and has extensive applications in industry. The application of non-azeotropic binary mixtures can not only meet the environmental requirements of modern industrial development, but also improve the coefficient of performance (COP) of many systems. Therefore, studying the boiling heat transfer characteristics of non-azeotropic mixtures is important on improving their potential industrial application. This article selected ethylene glycol/deionized water (EG/DW) at varies concentration as the research working fluids, and conducted experimental research on the pool boiling performance. At the same time, the thermophysical parameters of the mixtures were studied and analyzed. The results showed that the concentration of EG in the mixture had a significant impact on the thermal properties and temperature glide of the mixture, where both affected the heat transfer deterioration. Based on experimental data, six widely used heat transfer coefficient prediction correlations were used for calculation, and two of them were modified. The deviation between the modified correlations and the experimental results remained within 20%.

  • Open Access

    Performance Evaluation of LiBr-H2O and LiCl-H2O Working Pairs in Compression-Assisted Double-Effect Absorption Refrigeration Systems for Utilization of Low-Temperature Heat Sources

    by Tong Lei, Zuoqin Qian, Jie Ren

    To improve the performance of conventional double-effect absorption refrigeration systems (DEARS), new series parallel (SP) and reverse parallel (RP) configurations using LiCl-H2O and LiBr-H2O as working fluids, combined with two vapor compressors (VC), are proposed and thermodynamically evaluated. The effects of the distribution ratio (D) and compression ratio (CR) on the system performance are discussed. The results reveal that both configurations can extend the operation ranges of DEARS effectively at a higher distribution ratio, and the performance for low-grade heat source utilization is improved substantially by the use of VC. The compressor positioned between the evaporator and absorber is superior to that between the high-pressure generator and low-pressure generator because of the better performance improvement and larger operating ranges. In all the examined cases, LiCl-H2O systems perform better than LiBr-H2O systems in terms of the coefficient of performance (COP) and exergetic efficiency. At the higher CR of approximately 2, the compression-assisted DEARS can be driven by heat sources below 100 °C with high levels of COPs above 1.16 for the LiBr-H2O working pair and 1.29 for the LiCl-H2O working pair. The system can operate at the optimum condition by adjusting the CR values according to the characteristics of the heat sources.


  • Open Access

    A Comprehensive Experimental Investigation of Additives to Enhance Pool Boiling Heat Transfer of a Non-Azeotropic Mixture

    by Chen Xu, Zuoqin Qian, Jie Ren

    Adding nanoparticles or surfactants to pure working fluid is a common and effective method to improve the heat transfer performance of pool boiling. The objective of this research is to determine whether additives have the same efficient impact on heat transfer enhancement of the non-azeotropic mixture. In this paper, Ethylene Glycol/Deionized Water (EG/DW) was selected as the representing non-azeotropic mixture, and a comparative experiment was carried out between it and the pure working fluid. In addition, the effects of different concentrations of additives on the pool boiling heat transfer performance under different heat fluxes were experimentally studied, including TiO2 nanoparticles with different particle diameters, different kinds of surfactants, and mixtures of nanofluids and surfactants. The experimental results showed that the nanoparticles deteriorated the heat transfer of the EG/DW solution, while the surfactant enhanced the heat transfer of the solution when the concentration closed to a critical mass fraction (CMC). However, the improvement effect was unsteady with the increase in the heat flux density. The experimental results suggest that the mass transfer resistance of the non-azeotropic mixture is the most important factor in affecting heat transfer enhancement. Solutions with 20 nm TiO2 obtained a steady optimum heat transfer improvement by adding surfactants.