Yong‐Sheng He
Research Subjects
Yong‐Sheng He has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Rui Hu
State Key Laboratory of Solidification Processing Northwestern Polytechnical University 710072 Xi'an China
2 shared publicationsTao He
Western Superconducting Technologies Co Ltd Shaanxi Province Engineering Laboratory for Aerial Material 710018 Xi'an China
2 shared publicationsWen‐Zhong Luo
Western Superconducting Technologies Co Ltd Shaanxi Province Engineering Laboratory for Aerial Material 710018 Xi'an China
2 shared publicationsXiang‐Hong Liu
Western Superconducting Technologies Co Ltd Shaanxi Province Engineering Laboratory for Aerial Material 710018 Xi'an China
2 shared publicationsYun‐Jin Lai
Western Superconducting Technologies Co Ltd Shaanxi Province Engineering Laboratory for Aerial Material 710018 Xi'an China
1 shared publicationYu‐Jun Du
Western Superconducting Technologies Co Ltd Shaanxi Province Engineering Laboratory for Aerial Material 710018 Xi'an China
1 shared publication
Latest Publications
- 24 August 2018
- Published by Wiley in Rare Metals
- Vol. 37 (11) , 942-951
Microstructure and mechanical properties of a new Ti 2 AlNb‐based alloy after aging treatment
A new Ti 2 AlNb‐based alloy with the composition of Ti–22Al–25Nb–1Mo–1V–1Zr–0.2Si (at%) was fabricated in the sequence of arc melting, forging, solid solution and aging. Present paper focuses on the effects of aging temperatures (700, 750, 800, 850 and 900 °C) on microstructure, room‐temperature tensile properties as well as tensile properties at 650 °C and creep properties at 650 °C/150 MPa. It is obvious that the aging treatment promotes the precipitation of O lathes from B2 matrix. With aging temperature increasing, the content of O phase decreases and its size increases gradually, which leads to the decrease in tensile strengths both at room temperature and 650 °C and a little increase in ductility. For creep properties, the sample aged at 700 °C shows the best creep resistance due to its extremely high O phase content. Aging at 800 °C leads to the decrease in the content of O phase and softening of the alloy significantly. However, with aging temperature further increasing from 800 to 900 °C, the precipitated O phase will be coarsened gradually, which strengthens the alloy again.
- 24 August 2018
- Published by Wiley in Rare Metals
- Vol. 37 (11) , 942-951
Microstructure and mechanical properties of a new Ti 2 AlNb‐based alloy after aging treatment
A new Ti 2 AlNb‐based alloy with the composition of Ti–22Al–25Nb–1Mo–1V–1Zr–0.2Si (at%) was fabricated in the sequence of arc melting, forging, solid solution and aging. Present paper focuses on the effects of aging temperatures (700, 750, 800, 850 and 900 °C) on microstructure, room‐temperature tensile properties as well as tensile properties at 650 °C and creep properties at 650 °C/150 MPa. It is obvious that the aging treatment promotes the precipitation of O lathes from B2 matrix. With aging temperature increasing, the content of O phase decreases and its size increases gradually, which leads to the decrease in tensile strengths both at room temperature and 650 °C and a little increase in ductility. For creep properties, the sample aged at 700 °C shows the best creep resistance due to its extremely high O phase content. Aging at 800 °C leads to the decrease in the content of O phase and softening of the alloy significantly. However, with aging temperature further increasing from 800 to 900 °C, the precipitated O phase will be coarsened gradually, which strengthens the alloy again.
- 9 August 2018
- Published by Wiley in Rare Metals
- Vol. 37 (10) , 838-845
Oxidation behavior of a novel multi‐element alloyed Ti 2 AlNb‐based alloy in temperature range of 650–850 °C
The oxidation behavior of a novel multi‐element alloyed Ti 2 AlNb‐based alloy (Ti–22Al–25Nb–1Mo–1V–1Zr–0.2Si) was studied in the temperature range of 650–850 °C. X‐ray diffraction (XRD) and scanning electron microscopy (SEM) equipped with an energy‐dispersive spectroscopy (EDS) were used to identify the phase constituents and microstructure of the scales formed on the specimens after oxidation at different temperatures. Isothermal oxidation tests show that the oxidation rate of the alloyed Ti 2 AlNb‐based alloy is obviously reduced at all temperatures, and the mass gains are very low for this alloy in comparison with those of Ti–22Al–25Nb alloy. The alloying elements Mo, V, Zr and Si have an obvious affect on the oxidation products of the alloys. The improved oxidation resistance for the alloy is ascribed to the introduction of Mo, V, Zr and Si elements, which are beneficial to the selective oxidation of Al to form protective oxides while are disadvantage of the formation of poor oxidation resistance oxides such as AlNbO 4 .
- 9 August 2018
- Published by Wiley in Rare Metals
- Vol. 37 (10) , 838-845
Oxidation behavior of a novel multi‐element alloyed Ti 2 AlNb‐based alloy in temperature range of 650–850 °C
The oxidation behavior of a novel multi‐element alloyed Ti 2 AlNb‐based alloy (Ti–22Al–25Nb–1Mo–1V–1Zr–0.2Si) was studied in the temperature range of 650–850 °C. X‐ray diffraction (XRD) and scanning electron microscopy (SEM) equipped with an energy‐dispersive spectroscopy (EDS) were used to identify the phase constituents and microstructure of the scales formed on the specimens after oxidation at different temperatures. Isothermal oxidation tests show that the oxidation rate of the alloyed Ti 2 AlNb‐based alloy is obviously reduced at all temperatures, and the mass gains are very low for this alloy in comparison with those of Ti–22Al–25Nb alloy. The alloying elements Mo, V, Zr and Si have an obvious affect on the oxidation products of the alloys. The improved oxidation resistance for the alloy is ascribed to the introduction of Mo, V, Zr and Si elements, which are beneficial to the selective oxidation of Al to form protective oxides while are disadvantage of the formation of poor oxidation resistance oxides such as AlNbO 4 .