Muhammad Istiaque Haider
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Muhammad Istiaque Haider has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Nathan Salowitz
Department of Mechanical Engineering, University of Wisconsin-Milwaukee, Milwaukee, WI, United States of America
8 shared publications - Maysam Rezaee
University of Wisconsin - Milwaukee, Milwaukee, WI
5 shared publications - Armin Yazdi
University of Wisconsin - Milwaukee, Milwaukee, WI
4 shared publications Li-Chih Tsai
Department of Biomedical and Health Informatics, University of Wisconsin-Milwaukee, Milwaukee, USA
2 shared publicationsAfsaneh Moghadam
University of Wisconsin - Milwaukee, Milwaukee, WI
1 shared publicationAmeralys Correa
University of Wisconsin - Milwaukee, Milwaukee, WI
1 shared publication
Latest Publications
- Open Access
- 12 October 2023
- Published by Wisconsin Space Grant Consortium in Proceedings of the Wisconsin Space Conference
Analysis of Shape-Memory-Alloy Fiber Interface Strength for Optimization of Self-Healing Composites
Self-healing materials, possessing an innate ability to mend damage and restore structural strength, have tremendous potential to improve safety and reliability, especially in space applications where recovery or manual performance of repairs may be prohibitive, dangerous, or impossible. Self-healing metallic materials developed with Nickel Titanium (NiTi) Shape Memory Alloy (SMA) reinforcement showed a promising prospect for recovering from larger scale damage. However, NiTi is known to form an inert oxide (TiO2) surface layer that is extremely hard to attach to. In this research, to promote better strength between the fiber and matrix, TiO2 surface layer has been removed by etching the NiTi wires in an inert environment and a pull test has been performed to evaluate the resulting change in adhesion strength between the fiber and metallic matrix. The experimental investigation of these interface fracture scenarios will enable the efficient design of composite materials.
- 12 October 2023
- Published by Wisconsin Space Grant Consortium in Proceedings of the Wisconsin Space Conference
Open AccessAnalysis of Shape-Memory-Alloy Fiber Interface Strength for Optimization of Self-Healing Composites
Self-healing materials, possessing an innate ability to mend damage and restore structural strength, have tremendous potential to improve safety and reliability, especially in space applications where recovery or manual performance of repairs may be prohibitive, dangerous, or impossible. Self-healing metallic materials developed with Nickel Titanium (NiTi) Shape Memory Alloy (SMA) reinforcement showed a promising prospect for recovering from larger scale damage. However, NiTi is known to form an inert oxide (TiO2) surface layer that is extremely hard to attach to. In this research, to promote better strength between the fiber and matrix, TiO2 surface layer has been removed by etching the NiTi wires in an inert environment and a pull test has been performed to evaluate the resulting change in adhesion strength between the fiber and metallic matrix. The experimental investigation of these interface fracture scenarios will enable the efficient design of composite materials.
- 28 September 2023
- Published by Wiley in Advanced Engineering Materials
- Vol. 25 (22)
On the Nature of Post‐Constrained Recovery Residual Stress of NiTi Shape Memory Alloys
In this article, the nature of the post‐constrained recovery residual stress (PCRRS) observed in nickel titanium (NiTi) shape memory alloys (SMAs) subjected to constrained recovery and returned to a low‐temperature state while remaining constrained is investigated. After performing the thermomechanical cycling to produce the PCRRS state, four experiments are performed with different deflection profiles applied from the PCRRS state, and the changes in the residual stress is observed. All tests produce a gradual decrease in stress after every load cycle, similar to cyclic softening. However, repetition of the process used to initially generate PCRRS restores the initial magnitude of the PCRRS, indicating that the decrease in residual stress is a stable, repeatable, and reversible phenomenon, and not true material degradation. To better understand the nature of PCRRS, an analysis is performed comparing the modulus relating stress and strain at different points along the thermomechanical loading path. In this analysis, it is shown that NiTi has a combination of twinned and detwinned martensite in the PCRRS state. Understanding the nature of PCRRS, properties and its stability have the potential for advanced engineering applications such as self‐healing and fatigue‐resistant materials by generating stresses without continuous actuation over a long period of time.
- 28 September 2023
- Published by Wiley in Advanced Engineering Materials
- Vol. 25 (22)
On the Nature of Post‐Constrained Recovery Residual Stress of NiTi Shape Memory Alloys
In this article, the nature of the post‐constrained recovery residual stress (PCRRS) observed in nickel titanium (NiTi) shape memory alloys (SMAs) subjected to constrained recovery and returned to a low‐temperature state while remaining constrained is investigated. After performing the thermomechanical cycling to produce the PCRRS state, four experiments are performed with different deflection profiles applied from the PCRRS state, and the changes in the residual stress is observed. All tests produce a gradual decrease in stress after every load cycle, similar to cyclic softening. However, repetition of the process used to initially generate PCRRS restores the initial magnitude of the PCRRS, indicating that the decrease in residual stress is a stable, repeatable, and reversible phenomenon, and not true material degradation. To better understand the nature of PCRRS, an analysis is performed comparing the modulus relating stress and strain at different points along the thermomechanical loading path. In this analysis, it is shown that NiTi has a combination of twinned and detwinned martensite in the PCRRS state. Understanding the nature of PCRRS, properties and its stability have the potential for advanced engineering applications such as self‐healing and fatigue‐resistant materials by generating stresses without continuous actuation over a long period of time.
- Open Access
Investigation into the Performance of NiTi Shape Memory Alloy Wire Reinforced Sn-Bi Self-Healing Metal Matrix Composite
Self-healing materials have the potential to create a paradigm shift in the life cycle design of engineered structures, by changing the relation between material damage and structural failure, affecting structures’ lifetime, safety, and reliability. However, the knowledge of self-healing capabilities in metallic materials is still in its infancy compared to other material systems because of challenges in the synthesis of organized and complex structures. This paper presents a study of a metal matrix composite system that was synthesized with an off-eutectic Tin (Sn)-Bismuth (Bi) alloy matrix, reinforced with Nickel–Titanium (NiTi) shape memory alloy (SMA) wires. The ability to close cracks, recover bulk geometry, and regenerate strength upon the application of heat was investigated. NiTi wires were etched and coated in flux before being incorporated into the matrix to prevent disbonding with the matrix. Samples were subjected to large deformations in a three-point bending setup. Subsequent thermo-mechanical testing of the composites confirmed the materials’ ability to restore their geometry and recover strength, without using any consumable components. Self-healing was accomplished through a combination of activation of the shape memory effect in the NiTi to recover the samples’ original macroscopic geometry, closing cracks, and melting of the eutectic material in the matrix alloy, which resealed the cracks. Subsequent testing indicated a 92% strength recovery.
Open AccessInvestigation into the Performance of NiTi Shape Memory Alloy Wire Reinforced Sn-Bi Self-Healing Metal Matrix Composite
Self-healing materials have the potential to create a paradigm shift in the life cycle design of engineered structures, by changing the relation between material damage and structural failure, affecting structures’ lifetime, safety, and reliability. However, the knowledge of self-healing capabilities in metallic materials is still in its infancy compared to other material systems because of challenges in the synthesis of organized and complex structures. This paper presents a study of a metal matrix composite system that was synthesized with an off-eutectic Tin (Sn)-Bismuth (Bi) alloy matrix, reinforced with Nickel–Titanium (NiTi) shape memory alloy (SMA) wires. The ability to close cracks, recover bulk geometry, and regenerate strength upon the application of heat was investigated. NiTi wires were etched and coated in flux before being incorporated into the matrix to prevent disbonding with the matrix. Samples were subjected to large deformations in a three-point bending setup. Subsequent thermo-mechanical testing of the composites confirmed the materials’ ability to restore their geometry and recover strength, without using any consumable components. Self-healing was accomplished through a combination of activation of the shape memory effect in the NiTi to recover the samples’ original macroscopic geometry, closing cracks, and melting of the eutectic material in the matrix alloy, which resealed the cracks. Subsequent testing indicated a 92% strength recovery.
- Open Access
- 25 February 2022
- Published by Wisconsin Space Grant Consortium in Proceedings of the Wisconsin Space Conference
- Vol. 1 (1)
Explorations of Post Constrained Recovery Residual Stress of Shape Memory Alloys in Self-healing Applications
Self-healing materials with intrinsic capabilities of geometric restoration and damage recovery have a tremendous potential to improve product safety and reliability, especially in space applications where recovery or manual performance of repairs may be prohibitive, dangerous, or impossible. Self-healing materials typically incorporate a complex internal structure containing constituent materials of different functionality and one of the primary methods is to reinforce self-healing materials with shape memory alloys that can be activated to restore geometry and close a fracture. Recent experimental investigation revealed that Nickel Titanium (NiTi) shape memory alloys (SMAs) could repeatedly produce stable residual stresses following constrained recovery when held in a constrained condition during temperature change through the forward and reverse transformations. The ability to produce this post constrained recovery residual stress (PCRRS) in a low temperature state, without continuous actuation, and to regenerate it repeatedly have the potential to advance self-healing capabilities and even damage prevention.
- 25 February 2022
- Published by Wisconsin Space Grant Consortium in Proceedings of the Wisconsin Space Conference
- Vol. 1 (1)
Open AccessExplorations of Post Constrained Recovery Residual Stress of Shape Memory Alloys in Self-healing Applications
Self-healing materials with intrinsic capabilities of geometric restoration and damage recovery have a tremendous potential to improve product safety and reliability, especially in space applications where recovery or manual performance of repairs may be prohibitive, dangerous, or impossible. Self-healing materials typically incorporate a complex internal structure containing constituent materials of different functionality and one of the primary methods is to reinforce self-healing materials with shape memory alloys that can be activated to restore geometry and close a fracture. Recent experimental investigation revealed that Nickel Titanium (NiTi) shape memory alloys (SMAs) could repeatedly produce stable residual stresses following constrained recovery when held in a constrained condition during temperature change through the forward and reverse transformations. The ability to produce this post constrained recovery residual stress (PCRRS) in a low temperature state, without continuous actuation, and to regenerate it repeatedly have the potential to advance self-healing capabilities and even damage prevention.
- Open Access
- 24 December 2019
- Published by Springer Nature in Scientific Reports
- Vol. 9 (1) , 1-11
Quantitative peel test for thin films/layers based on a coupled parametric and statistical study
The adhesion strength of thin films is critical to the durability of micro and nanofabricated devices. However, current testing methods are imprecise and do not produce quantitative results necessary for design specifications. The most common testing methods involve the manual application and removal of unspecified tape. This overcome many of the challenges of connecting to thin films to test their adhesion properties but different tapes, variation in manual application, and poorly controlled removal of tape can result in wide variation in resultant forces. Furthermore, the most common tests result in a qualitative ranking of film survival, not a measurement with scientific units. This paper presents a study into application and peeling parameters that can cause variation in the peeling force generated by tapes. The results of this study were then used to design a test methodology that would control the key parameters and produced repeatable quantitative measurements. Testing using the resulting method showed significant improvement over more standard methods, producing measured results with reduced variation. The new method was tested on peeling a layer of paint from a PTFE backing and was found to be sensitive enough to register variation in force due to differing peeling mechanisms within a single test.
- 24 December 2019
- Published by Springer Nature in Scientific Reports
- Vol. 9 (1) , 1-11
Open AccessQuantitative peel test for thin films/layers based on a coupled parametric and statistical study
The adhesion strength of thin films is critical to the durability of micro and nanofabricated devices. However, current testing methods are imprecise and do not produce quantitative results necessary for design specifications. The most common testing methods involve the manual application and removal of unspecified tape. This overcome many of the challenges of connecting to thin films to test their adhesion properties but different tapes, variation in manual application, and poorly controlled removal of tape can result in wide variation in resultant forces. Furthermore, the most common tests result in a qualitative ranking of film survival, not a measurement with scientific units. This paper presents a study into application and peeling parameters that can cause variation in the peeling force generated by tapes. The results of this study were then used to design a test methodology that would control the key parameters and produced repeatable quantitative measurements. Testing using the resulting method showed significant improvement over more standard methods, producing measured results with reduced variation. The new method was tested on peeling a layer of paint from a PTFE backing and was found to be sensitive enough to register variation in force due to differing peeling mechanisms within a single test.
- 12 September 2019
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 28 (10) , 105044
Investigation into post constrained recovery properties of nickel titanium shape memory alloys
Experimental investigations have found that nickel titanium (NiTi) shape memory alloys (SMAs) exhibit a phenomenon wherein the material can be recoverably deformed in its low temperature martensitic state, thermally actuated to its austenite state while constrained from returning to its parent geometry, and upon ceasing actuation and return to the low temperature martensite state it will continue to generate post constrained recovery residual stresses (PCRRS). The ability to generate a PCRRS creates a new way for SMAs to be used but the stability of the PCRRS, response to subsequent loading, and underlying microstructural mechanisms that generate the PCRRS are poorly understood. This paper presents an experimental investigation into the thermomechanical response of NiTi beginning from a PCRRS state. Multiple formulations of NiTi were exposed to training and sequences of cyclic deformation and thermal actuation in this study. It was found that repeated application of 0.5% strain reduced the residual stress with each application and thermal actuation would restore the original PCRRS. Training and mechanically working the material stabilized the thermomechanical response and did not significantly degrade the magnitude of the PCRRS. Understanding of PCRRS supports a new way for materials to be used as actuators, storing potential energy in material structures that may be beneficial to self-healing material, fatigue crack prevention and other applications.
- 12 September 2019
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 28 (10) , 105044
Investigation into post constrained recovery properties of nickel titanium shape memory alloys
Experimental investigations have found that nickel titanium (NiTi) shape memory alloys (SMAs) exhibit a phenomenon wherein the material can be recoverably deformed in its low temperature martensitic state, thermally actuated to its austenite state while constrained from returning to its parent geometry, and upon ceasing actuation and return to the low temperature martensite state it will continue to generate post constrained recovery residual stresses (PCRRS). The ability to generate a PCRRS creates a new way for SMAs to be used but the stability of the PCRRS, response to subsequent loading, and underlying microstructural mechanisms that generate the PCRRS are poorly understood. This paper presents an experimental investigation into the thermomechanical response of NiTi beginning from a PCRRS state. Multiple formulations of NiTi were exposed to training and sequences of cyclic deformation and thermal actuation in this study. It was found that repeated application of 0.5% strain reduced the residual stress with each application and thermal actuation would restore the original PCRRS. Training and mechanically working the material stabilized the thermomechanical response and did not significantly degrade the magnitude of the PCRRS. Understanding of PCRRS supports a new way for materials to be used as actuators, storing potential energy in material structures that may be beneficial to self-healing material, fatigue crack prevention and other applications.
- 9 September 2019
- Published by ASME International
Mechanics of Post Constrained Recovery Residual Stress Produced by NiTi
Recent research has revealed that Nickel Titanium (NiTi) shape memory alloys can produce residual stresses after undergoing constrained recovery and returning to their low temperature, martensitic state while still constrained. The nature and underlying mechanisms that cause this post constrained recovery residual stress (PCRRS) are not well understood. This paper presents experimental research and results seeking to further understand the PCRRS. Experiments were performed on multiple formulations of NiTi subjected to: 1) Cyclic loading and training before producing PCRRS, 2) Repeated thermomechanical loading with large strains followed by a thermal cycle to create and re-generated the PCRRS, and 3) Creation of the PCRRS followed by repeated cycles of small, 0.5% strains. Experiments found that the training in 1) did not significantly alter the ability to produce PCRRS or its magnitude. Straining samples from the PCRRS state could reduce the residual stress state to zero stress, but the PCRRS could be recreated by repeating thermal actuation with the only significant variation being a reduction in magnitude for the first to second cycle. Multiple small strain cycles applied from the PCRRS state caused an incremental reduction in residual stress. The full PCRRS could be re-created by repeating the initial thermomechanical cycle. The values of the residual stress varied across the first 3 sets of cycles, but from the third set onward the response stabilized. These results indicate that the primary mechanisms for generating a PCRRS are stable and recoverable with only minor and diminishing variations due to training or repeated regeneration of the PCRRS. Grain boundary stabilization and similar mechanisms may be responsible for the minor variation between the first few regenerations of the PCRRS. The incremental reduction in the residual stress after exposure to small 0.5% strains must be due to a recoverable process like partial and accumulating detwinning of the NiTi with each load cycle. Further work is underway to perform microstructural analysis of samples in the various states to further the theorized material states. The ability to generate and control PCRRS has the potential to find new application and advance capabilities in fields like self-healing and fatigue resistant materials by generating stresses without the continuous application of heat energy. New forms of actuation could also be developed based on the potential energy stored in a structure through PCRRS.
- 9 September 2019
- Published by ASME International
Mechanics of Post Constrained Recovery Residual Stress Produced by NiTi
Recent research has revealed that Nickel Titanium (NiTi) shape memory alloys can produce residual stresses after undergoing constrained recovery and returning to their low temperature, martensitic state while still constrained. The nature and underlying mechanisms that cause this post constrained recovery residual stress (PCRRS) are not well understood. This paper presents experimental research and results seeking to further understand the PCRRS. Experiments were performed on multiple formulations of NiTi subjected to: 1) Cyclic loading and training before producing PCRRS, 2) Repeated thermomechanical loading with large strains followed by a thermal cycle to create and re-generated the PCRRS, and 3) Creation of the PCRRS followed by repeated cycles of small, 0.5% strains. Experiments found that the training in 1) did not significantly alter the ability to produce PCRRS or its magnitude. Straining samples from the PCRRS state could reduce the residual stress state to zero stress, but the PCRRS could be recreated by repeating thermal actuation with the only significant variation being a reduction in magnitude for the first to second cycle. Multiple small strain cycles applied from the PCRRS state caused an incremental reduction in residual stress. The full PCRRS could be re-created by repeating the initial thermomechanical cycle. The values of the residual stress varied across the first 3 sets of cycles, but from the third set onward the response stabilized. These results indicate that the primary mechanisms for generating a PCRRS are stable and recoverable with only minor and diminishing variations due to training or repeated regeneration of the PCRRS. Grain boundary stabilization and similar mechanisms may be responsible for the minor variation between the first few regenerations of the PCRRS. The incremental reduction in the residual stress after exposure to small 0.5% strains must be due to a recoverable process like partial and accumulating detwinning of the NiTi with each load cycle. Further work is underway to perform microstructural analysis of samples in the various states to further the theorized material states. The ability to generate and control PCRRS has the potential to find new application and advance capabilities in fields like self-healing and fatigue resistant materials by generating stresses without the continuous application of heat energy. New forms of actuation could also be developed based on the potential energy stored in a structure through PCRRS.
- 9 September 2019
- Published by ASME International
Quantitative Measurement of Thin Film Adhesion Force
Thin film and micro-fabricated devices are increasingly being used in actuators, sensors, and processors deployed in smart materials. The physical survival of these devices is paramount to their usefulness but existing methods for testing and analysis are limited and challenging due to their properties. The most common test involve the manual application and removal of (unspecified) tape but does not provide a result in scientific units and has large variation (> 35%). This paper presents a study into the effects of parameters of tape application and peeling on the adhesion strength of the tape. This information was then used to create a test methodology using commonly available laboratory equipment, which would control these parameters to minimize variation and produce repeatable quantitative results. Experiments using this test methodology were performed with tape directly adhered to several different substrates as well as tape adhered to a thin film which was then peeled off of a backing. Ongoing work is seeking to identify and address different forms of failure including adhesive failure, cohesive failure, or survival.
- 9 September 2019
- Published by ASME International
Quantitative Measurement of Thin Film Adhesion Force
Thin film and micro-fabricated devices are increasingly being used in actuators, sensors, and processors deployed in smart materials. The physical survival of these devices is paramount to their usefulness but existing methods for testing and analysis are limited and challenging due to their properties. The most common test involve the manual application and removal of (unspecified) tape but does not provide a result in scientific units and has large variation (> 35%). This paper presents a study into the effects of parameters of tape application and peeling on the adhesion strength of the tape. This information was then used to create a test methodology using commonly available laboratory equipment, which would control these parameters to minimize variation and produce repeatable quantitative results. Experiments using this test methodology were performed with tape directly adhered to several different substrates as well as tape adhered to a thin film which was then peeled off of a backing. Ongoing work is seeking to identify and address different forms of failure including adhesive failure, cohesive failure, or survival.
- 10 September 2018
- Published by ASME International
Experimental Exploration of Post Constrained Recovery Mechanics of NiTi
Shape memory alloys (SMAs) have tremendous potential use as actuators in mechanical systems due to their high specific energy density. Large recovery stresses can be generated when Nickel Titanium (NiTi), the most widely used SMA, undergoes constrained recovery where it is held in a deformed geometry and heated from a detwinned martensite phase to austenite phase. Recent experimental results have found that residual stresses can also be generated in NiTi after returning to a low temperature geometrically constrained state. This paper presents experimental results performed on NiTi wire samples where wire was: 1) deformed from a low temperature twinned martensite state to produce a strain that would be recoverable in an unloaded state 2) held at that strain state and heated above the austenite finish transition temperature and then cooled back below the martensite transition finish temperature while recording the forces generated. It was found that a residual load was produced in the low temperature state. Results from further testing beyond this point showed repeatability with application of small and large strains. Post constrained recovery stresses have the potential to be used to generate residual stresses in structures in a low energy, un-actuated state with a remaining potential for thermal actuation.
- 10 September 2018
- Published by ASME International
Experimental Exploration of Post Constrained Recovery Mechanics of NiTi
Shape memory alloys (SMAs) have tremendous potential use as actuators in mechanical systems due to their high specific energy density. Large recovery stresses can be generated when Nickel Titanium (NiTi), the most widely used SMA, undergoes constrained recovery where it is held in a deformed geometry and heated from a detwinned martensite phase to austenite phase. Recent experimental results have found that residual stresses can also be generated in NiTi after returning to a low temperature geometrically constrained state. This paper presents experimental results performed on NiTi wire samples where wire was: 1) deformed from a low temperature twinned martensite state to produce a strain that would be recoverable in an unloaded state 2) held at that strain state and heated above the austenite finish transition temperature and then cooled back below the martensite transition finish temperature while recording the forces generated. It was found that a residual load was produced in the low temperature state. Results from further testing beyond this point showed repeatability with application of small and large strains. Post constrained recovery stresses have the potential to be used to generate residual stresses in structures in a low energy, un-actuated state with a remaining potential for thermal actuation.