R. S. Seisembayev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
R. S. Seisembayev has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Anastassiya Semenova
Institute of Metallurgy and Ore Beneficiation, Satbayev University, Almaty 050013, Kazakhstan
3 shared publications - Sergey Kvyatkovskiy
Satbayev University, Institute of Metallurgy and Ore Beneficiation JSC, Almaty, Kazakhstan
2 shared publications - Alina Nitsenko
Institute of Metallurgy and Ore Beneficiation, Satbayev University, 050010 Almaty, Kazakhstan
1 shared publication - Bulat Sukurov
JCS Institute of Metallurgy and Ore Beneficiation, Satbayev University, Almaty 050013, Kazakhstan
1 shared publication - E. A. Sit’kO
Satbayev University, Institute of Metallurgy and Ore Beneficiation JSC, Almaty, Kazakhstan
1 shared publication F.KH. Tuleutay
1 shared publication
Latest Publications
- 25 December 2020
- Published by Institute of Metallurgy and Ore Benefication (Publications) in Kompleksnoe Ispolzovanie Mineralnogo Syra = Complex Use of Mineral Resources
- Vol. 315 (4) , 49-56
Study of physical and chemical properties of tellurium-containing middlings
The process experts are concerned in tellurium due to its various physical and chemical properties. The copper anode slime is the main industrial source of tellurium, after processing of that tellurium becomes marketable product and can be sold both in elemental form and tellurium-containing middling. Physical and chemical properties of the tellurium-containing middling of Kazakhmys Smelting LLP produced in 2018 have been studied in this paper. The following methods have been applied during the study: particle size distribution, X-ray phase, X-ray fluorescence and scanning electron probe microscopy. It was found that material is mainly represented by the large pieces of 0.2 mm in size, with moisture content of 15.57 %, bulk density of 0.8 g/cm3 without tapping and 0.88 g/cm3 with tapping, the angle friction - 33°. The elemental composition of the material was determined by X-ray fluorescence method as follows, wt. %: Cu – 33.327; Te – 21.863; Se – 0.766, O – 35.116; S – 5.045. X-ray phase analysis showed that material is mainly in the amorphous state, the following phases had been identified: Cu2.5SO4(OH)3·2H2O, Cu3(SO4)(OH)4, CuSO4(H2O)3. Tellurium-containing phases could not be detected due to strong amorphism. Hydrosulfate forms of copper in the form of flakes have been found on the surface of the middlings by electron probe microscopy. EDS analysis of individual areas showed that patina also contains small amounts of chlorine, selenium and up to 25 % tellurium, in addition to such elements as copper, sulfur and oxygen. Small amounts of sulfur, chromium, selenium and up to 45 % of oxygen has been found in the open area of material, that is specific for its oxidation.
- 25 December 2020
- Published by Institute of Metallurgy and Ore Benefication (Publications) in Kompleksnoe Ispolzovanie Mineralnogo Syra = Complex Use of Mineral Resources
- Vol. 315 (4) , 49-56
Study of physical and chemical properties of tellurium-containing middlings
The process experts are concerned in tellurium due to its various physical and chemical properties. The copper anode slime is the main industrial source of tellurium, after processing of that tellurium becomes marketable product and can be sold both in elemental form and tellurium-containing middling. Physical and chemical properties of the tellurium-containing middling of Kazakhmys Smelting LLP produced in 2018 have been studied in this paper. The following methods have been applied during the study: particle size distribution, X-ray phase, X-ray fluorescence and scanning electron probe microscopy. It was found that material is mainly represented by the large pieces of 0.2 mm in size, with moisture content of 15.57 %, bulk density of 0.8 g/cm3 without tapping and 0.88 g/cm3 with tapping, the angle friction - 33°. The elemental composition of the material was determined by X-ray fluorescence method as follows, wt. %: Cu – 33.327; Te – 21.863; Se – 0.766, O – 35.116; S – 5.045. X-ray phase analysis showed that material is mainly in the amorphous state, the following phases had been identified: Cu2.5SO4(OH)3·2H2O, Cu3(SO4)(OH)4, CuSO4(H2O)3. Tellurium-containing phases could not be detected due to strong amorphism. Hydrosulfate forms of copper in the form of flakes have been found on the surface of the middlings by electron probe microscopy. EDS analysis of individual areas showed that patina also contains small amounts of chlorine, selenium and up to 25 % tellurium, in addition to such elements as copper, sulfur and oxygen. Small amounts of sulfur, chromium, selenium and up to 45 % of oxygen has been found in the open area of material, that is specific for its oxidation.
- 12 November 2020
- Published by Springer Nature in Metallurgist
- Vol. 64 (7-8) , 788-795
Extraction of Gold from Refractory Gold-Bearing Ores by Means of Reducing Pyrometallurgical Selection
- 12 November 2020
- Published by Springer Nature in Metallurgist
- Vol. 64 (7-8) , 788-795
Extraction of Gold from Refractory Gold-Bearing Ores by Means of Reducing Pyrometallurgical Selection
- 11 November 2020
- Published by Springer Nature in Metallurgist
- Vol. 64 (7-8) , 678-686
Processing Converter Slags with Total Utilization of All Components
- 11 November 2020
- Published by Springer Nature in Metallurgist
- Vol. 64 (7-8) , 678-686
Processing Converter Slags with Total Utilization of All Components