KSKarol Suprynowicz

Karol Suprynowicz

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Karol Suprynowicz has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    ZASTOSOWANIE PROSZKÓW LUMINESCENCYJNYCH W CYFROWEJ FOTOGRAFII PLAMKOWEJ

    by A. Kułak, Karol Suprynowicz, Jerzy Pisarek

    Do generacji obrazów plamkowych wykorzystano proszek luminescencyjny naniesiony w niewielkiej ilości na powierzchnię próbki i pobudzany do świecenia promieniowaniem UV. Uzyskano drobnoziarniste struktury plamkowe (speckle pattern) o bardzo wysokim kontraście i małym rozmiarze plamek, których kształt w przeciwieństwie do speckli laserowych jest kołowy, co ma istotne znaczenie dla skuteczności zastosowanych metod cyfrowej analizy obrazu. Pomiaru przemieszczeń i odkształceń dokonano poprzez cyfrową rejestrację obrazu i jego analizę przy użyciu procedur korelacyjnych. Wyniki zostały przedstawione poglądowo w postaci bitmap oraz w sposób bezpośredni w postaci tablic i wykresów. Opracowana metoda badawcza została przetestowana na płaskich próbkach drewnianych poddanych zginaniu trójpunktowemu.

  • Open Access

    Limit load and failure mechanisms of soda lime glass foam

    by Artur Mościcki, Jakub Pawlicki, Dominik Głowacki, Karol Suprynowicz


  • Determination of mechanical properties of rat’s artery using optimization based method and Ogden’s model

    by Michał Kowalik, Justyna Pyrzanowska, Agnieszka Piechal, Kamilla Blecharz-Klin, Ewa Widy-Tyszkiewicz, Karol Suprynowicz, Paweł Pyrzanowski


  • Investigation of Riveted Joints of Fiberglass Composite Materials

    by R. Bielawski, M. Kowalik, K. Suprynowicz, W. Rządkowski, P. Pyrzanowski


  • Analysis of the Crack Propagation Process in Concrete Beams Reinforced with BFRP Bars Using Digital Image Correlation Method

    by Marek Urbański, Andrzej Łapko, Karol Suprynowicz

    Application of the DIC (Digital Image Correlation) method for the analysis of crack initiation and propagation in RC beams reinforced by BFRP bars (Basalt Fibre Reinforced Polymer) is presented in the paper. Two dimensional, single camera DIC system was used to observe strain and crack distribution in such RC beams loaded using four point bending setup. BFRP bars have arose as an alternative to steel bars for RC (Reinforcement Concrete) members in aggressive environments. The low modulus of elasticity of BFRP bars lead on to large crack widths and, as a result, the design of BFRP Reinforced Concrete beams is often governed by SLS (Serviceability Limit State) criterion. Due to this it is necessary to explore specific crack propagation in concrete beams. Process of such beams degradation can be identified by comparison of strains and displacements obtained by DIC method, with the database of experiment results.


  • Possibility of Usage of Aluminium Rivet Nuts Connections in Composite Materials

    by Radosław Bielawski, Michał Kowalik, Karol Suprynowicz, Paweł Pyrzanowski

    Development and application of composite materials in modern industry are very dynamic. Composite materials seem to be replacing steel and aluminium ones. Composites are a cheaper solution, with similar mechanical strengths. Generally, there are two types of joints in composite structures: mechanical and adhesively bonded ones. The aim of the study was to determine the feasibility of riveted joints in composites materials. Static tensile test method was used. In the test there was used one type of glass fabric (Interglas 92140) from which two types of composite samples were prepared. In each sample there was used the same type of fiber with the same fiber orientation – 3 layers. Samples had dimensions of 220x100 mm and thickness of approximately 1.5 mm. They were connected to each other with aluminium rivet nuts (from 1 to 3) and placed in a metal frame with a screw connection which was made of screws with nominal thread pitch M5. Screws were tightened with constant torque. It was to provide an axial force to the sample during the tensile test. The frame was placed between cross-bars of tensile machine INSTRON 8516. The samples were stretched at a speed of 0.05 mm/s at a distance up to 20 mm. During the tensile test displacement of the samples and pull force were registered. Depending on the fiber orientations and number of rivet nuts composite damage models were described. On the basis of the results the possibility of usage of aluminium rivet nuts connections in composite materials was determined.


  • Determination of Mechanical Properties of Rat Aorta Using Ring-Shaped Specimen

    by Michał Kowalik, Justyna Pyrzanowska, Agnieszka Piechal, Kamilla Blecharz-Klin, Ewa Widy-Tyszkiewicz, Marcin Obszański, Karol Suprynowicz, Paweł Pyrzanowski

    Ring-shaped specimen is commonly used in tests for determination of mechanical properties for arteries in hoop direction, especially for small mammals such as rats or mice. Although ring test is a lot more convenient than the tests concerning strip specimens, interpretation of the experimental data might be inconclusive – it is difficult distinguish whether it's still straightening up or the actual tension begins. The basic problem is to properly define initial length of specimen, which is essential for strain calculation. The purpose of this study was to evaluate various methods for strain evaluation. Ten Wistar Albino Glaxo male rats (3 months old, body weight about 200g) were sacrificed by decapitation and arteries were immediately removed. Three specimens, each approximately 2–3mm long, from each rat were excised adjacent to the aortic arch. Couple different initial lengths, as well as Digital Image Correlation based extensometer results were used for strain-stress response calculations. In addition a 3D Finite Element model, with an Ogden constitutive model based material, was made for deeper investigation of specimen behavior. This study has shown that the testing procedure for determination of mechanical properties of arteries, based on ring-shaped specimen, is prone to errors. Stiffness calculations are very sensitive to the choice of initial length of the specimen. As the use of DIC proved to give very good correlation with experimental data this method will be used in further studies.


  • Research on the Surface Deformability of Reinforced Concrete Beams with the Use of Digital Image Correlation Method

    by Rafal Ostromecki, Karol Suprynowicz

    The results of experimental research on a single span reinforced concrete beams are presented in the paper. The study was undertaken to explain some issues, amongst which the most important one was the recognition of strain distribution in the shear zone of RC beams. It was decided to adopt the modified Digital Image Correlation Method (DIC) and the software created by K. Suprynowicz to follow the surface deformations. This was the first application of the software to the concrete structures behaviour analysis. Hence, another aim of the study was to confirm the proper susceptibility and usefulness of this tool for further research on concrete elements. What’s more the scope of the software future development was defined, that would allow for observation of some particular phenomena characteristic for concrete, like cracking. Finally, the conclusion is presented, that application of the proposed variant of DIC method to concrete structures is promising, although for the recognition of shear strain distribution it requires increasing the accuracy by increasing spatial resolution of images and modifications of the software.