MKMichał Kowalik

Michał Kowalik

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Michał Kowalik has a total of 57 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • GENERATIVE DESIGN-BASED IMPROVEMENT OF A BICYCLE CRANK

    by Michał KOWALIK, Mateusz Liwski, Mateusz Papis

    This study explores the application of generative design in improving bicycle crank geometry through an iterative workflow. The research utilized Autodesk Fusion 360 to develop a lightweight, structurally efficient crank, considering additive manufacturing via laser powder bed fusion (LPBF), 5-axis CNC milling, and casting as manufacturing routes. Candidate materials included Scalmalloy (an LPBF-optimized Al–Mg–Sc alloy), cast aluminum A356-T6, a titanium alloy Ti-6Al-4V, stainless steel 17-4PH, and fiber-reinforced polymers. Four iterations of a generative design with progressively refined boundary conditions were conducted to evaluate how loads, constraints, and geometric modifications shape the resulting candidates. The results indicate that an LPBF-manufactured Scalmalloy crank provided the most favorable balance between mass and static structural response among the evaluated alternatives, achieving approximately 27% mass reduction relative to the reference design. The findings demonstrate that generative design—framed as an iterative design exploration rather than a formal mathematical optimization—can inform the redesign of bicycle components when boundary conditions are progressively refined and material process compatibility is respected.

  • Open Access

    Post-Processing Strategies for Generative Design Outcomes in a UAV Tail Boom

    by Michał Piotr Kowalik, Piotr Stapiński, Mateusz Papis

    Generative design produces structurally efficient but organically shaped geometries that require post-processing before Fused Deposition Modeling (FDM) manufacturing. This paper compares two post-processing strategies applied to the same generative design outcome for an Unmanned Aerial Vehicle (UAV) tail boom: a complex variant faithful to the raw topology, and a simplified variant with symmetric arms, self-supporting geometry, and uniform cross-sections oriented toward FDM manufacturability. Both variants were evaluated using linear static and buckling finite element analysis underidentical loading conditions. Scaled prototypes of the simplified variant were FDM-printed at two infill configurations and physically load-tested. The manufacturing-oriented simplification reduced both mass and print time while eliminating support structures; peak stress remained well below the material limit. FEA-predicted stress concentrations correlated with observed fracture locations in physical tests. For lightly loaded polymer FDM structures, these results suggest that manufacturing-oriented simplification of generative design outcomes incurs a negligible structural penalty while improving printability and reducing production cost.

  • Open Access

    Automated Large-Format Additive Manufacturing of Foamed Polystyrene for Construction Applications

    by Michał Piotr Kowalik, Dawid Urbański, Kornad Kacprzak

    Construction remains largely manual in several key operations: formworks built from timber or steel, insulation boards hand-cut from EPS/XPS, prefabricated inserts machined from rigid foam, and 3D-printed concrete supports shaped from EPS blocks on site. Large-format additive manufacturing (LFAM) could automate all four, yet solid-polymer LFAM is limited by thermalshrinkage, weak interlayer bonding, and dimensional instability. We present the first LFAM process based on in-situ foamed thermoplastic extrusion: a screw extruder processes blowing agent-saturated polystyrene into 20–60 mm beads at 80–200 kg/m3. Foam expansion absorbs thermal contraction, so the process runs without heated chambers. Thermal conductivity of0.035–0.042 W/m K matches commercial EPS/XPS, making foamed polystyrene a candidate for automated insulation deposition. A concrete-casting trial further confirmed stay-in-place formworkcompatibility. Volumetric deposition reaches 0.35 m3/h—5–13×thatofsolid-polymer LFAMat equal mass throughput—fast enough for 3D-printed concrete void formers, supports, and inserts, with hybrid subtractive finishing within five minutes.

  • Algorithmic Determination of Femoral Neck Axis in Birmingham Hip Resurfacing: A Parametric CAD-Based Method

    by Michał Piotr Kowalik, Dawid Knaś, Krzysztof Zawiśliński

    Purpose: Birmingham Hip Resurfacing requires precise determination of the femoral head-neck axis to minimize risks of neck fracture, cortical notching, and component malposition. Existing methods rely on intraoperative estimation, generic guides, or semi-manual planning, all susceptible to anatomical variability. This study presents an automated parametric algorithm for determining the femoral neck axis from CT-derived models to support patient-specific surgical planning. Methods: The method utilizes segmented CT data converted to STEP format. Following artifact removal, the algorithm performs iterative cross-sectional analysis along the neck axis, identifying characteristic anatomical points: the neck isthmus, head centroid, and head apex. The axis is approximated from these points and refined through rotational optimization in 5 degree and 0.5 degree increments. The algorithm was evaluated on four femoral models in five spatial orientations each (20 test cases). Results: The algorithm achieved a mean validation score of 4.1/5.0 (82%). Three models with high-quality meshes scored 4-5, while one model with extensive artifacts scored 1-2, confirming sensitivity to input data quality. Repeatability was plus/minus 0.5 degrees in angular orientation and plus/minus 0.2 mm in isthmus position. Error propagation analysis indicated that CT-induced uncertainty (approximately 1.6 degrees upper bound) constitutes the limiting factor, not algorithmic precision. Physical prototyping confirmed viability for patient-specific instrument design. Conclusions: The method provides reproducible, automated femoral neck axis determination with plus/minus 0.5 degrees repeatability -- approximately three times smaller than CT-induced uncertainty and an order of magnitude below the 5-7 degree errors of conventional jigs. Future work should validate the method against clinical outcomes in larger cohorts.

  • Open Access

    Printing Path Geometry Controls Stress Concentration at Interlayer Notches in 3D-Printed Concrete: DIC Evidence and Mechanistic Interpretation

    by Adam Jakub Cisowski, Michał Piotr Kowalik

    Extrusion-based 3D concrete printing (3DCP) generates periodic interlayer notches whose geometry depends on the nozzle cross-section, rheology, and deposition conditions. These notches act as stress concentrators — yet no scalar stress concentration factors (SCF) have been reported for interlayer interfaces in 3DCP under compression. Nineteen five-layer specimens — printed with a circular nozzle (O) and a trapezoidal nozzle at nominal (P) and excessive (T) extrusion rates — were tested under uniaxial compression with 3D DIC. The measured SCF ranking (O > T > P) is consistent with the geometric severity ranking (O ≥ T > P), confirming that printing path geometry controls stressconcentration. SCF was evaluated from DIC-measured surface strains, which equal stress ratios in the linear-elastic regime. Measured SCF values (1.3–1.8) are 2–3 times lower than those obtainedin cast specimens with geometrically similar notch profiles (3.4–4.7), which is jointly explained by fracture process zone (FPZ) development, Theory of Critical Distances (TCD), and DIC virtual strain gauge (VSG) averaging. SCF decreased with load, consistent with progressive FPZ growth. Scatter was highest for circular-nozzle specimens, reflecting stochastic notch geometry. All specimens failed by matrix splitting or shear banding, not delamination, confirming adequate interlayer bond quality.

  • Open Access

    A Kinematic Prototype of a Compliant Artificial Prosthetic Knee Joint

    by Michał Kowalik, Erwin Rogoża, Aleksy Figurski, Mateusz Papis

    This study presents the development and kinematic evaluation of a compliant artificial knee joint prototype fabricated using multi-material 3D printing. The design integrates a rolling-contact compliant mechanism—derived from the CORE and D-CORE concepts—into a prosthetic knee construction, aiming to replicate biological joint behavior while reducing weight, mechanical complexity, and friction. The prototype underwent iterative refinement, including geometric modifications, material selection for flexure bands, and structural asymmetry to mitigate overextension and increase durability. The resulting joint exhibited hybrid kinematic characteristics, blending features of both single-axis and polycentric knee mechanisms, and achieved a functional flexion range of approximately 142 degrees. Initial cyclic tests confirmed satisfactory stiffness and shape recovery of flexure bands with optimized dimensions, although long-term fatigue performance remains a challenge. A basic spring-damper system was also integrated, potentially aligning the prototype with K-1/K-2 prosthetic classification. However, full validation requires further mechanical testing in accordance with ISO 10328 standards, as well as optimization of the damping system for commercial viability. This research demonstrates the feasibility and potential of compliant mechanisms in lower-limb prosthetics while identifying critical areas for future development.

  • Open Access

    Influence of 3D printing technology on reproducing cultural objects in the context of visually impaired people

    by Mateusz Papis, Paweł Kalski, Grzegorz Szuszkiewicz, Michał Piotr Kowalik

    The number of people with vision impairments is steadily increasing, emphasizing the need to prevent their exclusion from all spheres of public life, including cultural access. This research investigates the influence of 3D printing technologies on reproducing cultural objects to enhance...


  • Utilization of topology optimization and generative design for drone frame optimization

    by Michał Kowalik, Michał Śliwiński, Mateusz Papis

    Purpose: This study presents the process of optimizing a DJI F450 quadcopter using two optimization methods: topology optimization and generative design. The goal was to improve the overall performance of the unmanned aerial vehicle (UAV) by altering its geometry and comparing the use of different materials. The purpose of this paper is to reduce the mass of the original DJI F450 frame by 10%. Design/methodology/approach: To enable optimization using both methods, modifications were made to the original DJI F450 frame. A total of five cases were prepared: one for the original DJI F450 frame, three for topology optimization and one for generative design. Appropriate constraints were applied to simulate the real-world forces acting on the drone during flight. The various optimized frame designs underwent static analysis to evaluate stress, strain, displacement and safety factors. These results were then compared with those of the original DJI F450 frame, which also underwent static analysis. Findings: The results revealed that the optimized DJI F450 frames could achieve improved performance under flight-like load conditions, with reduced mass and comparable stress and strain levels. This demonstrates that engineering optimization, combined with additive manufacturing, can yield superior results, producing lighter, more capable organic structures compared to traditional frames. Originality/value: This research offers a novel perspective on optimizing UAV frames using topology optimization and generative design. The findings contribute to a deeper understanding of how engineering optimization, combined with additive manufacturing, can produce lighter, more capable structures for UAVs.


  • Open Access

    Test and comparison of different digitalization techniques for objects with surfaces difficult to scan

    by Michał Piotr Kowalik, Filip Pelowski, Ignacy Lipowiecki

    This article presents the results of research conducted as part of the project titled "Improvement of access to culture and activation of disabled and socially excluded persons" Gospostrateg-VI/0022/2021 co-financed by the National Centre for Research and Development. The aim of the...