Davide Smacchia
Research Subjects
Davide Smacchia has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Pablo Soto
TEAM, Universitat Politcnica de Valncia, Valencia, Spain
7 shared publications - Vicente Enrique Boria
Universitat Politècnica de València
7 shared publications - David Raboso
European Space Agency, Noordwijk, The Netherlands
5 shared publications - Carlos Alcaide
TEAM, Universitat Politcnica de Valncia, Valencia, Spain
4 shared publications - Jose Vicente Morro
TEAM, Universitat Politcnica de Valncia, Valencia, Spain
4 shared publications - Javier Ossorio
European High Power RF Space and Space Materials Laboratories, Valncia, Spain
3 shared publications
Latest Publications
- Open Access
- 13 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (10) , 5662-5669
Impact of Distortion on the Multipactor Threshold for Dual Carrier Digitally Modulated Signals
Multipactor under digitally modulated signals is a field of growing interest in the space industry. The need to operate with higher powers arises from the industry demand to increase data throughput, enabled by advances in space-born amplifiers. However, this often leads to signal distortion, which may alter the multipactor threshold measured in laboratory conditions. This work aims to characterize, through the combination of experimental tests and numerical simulations, how distortion affects the multipactor performance of microwave devices excited by modulated signals. To this end, several dual carrier modulated signals with different distortion levels are digitally created, simulated, and tested on the same multipactor sample. When the simulation configuration matches the laboratory conditions, an excellent degree of accuracy is reported. However, simulations also demonstrate that the nonzero time response of the sensors may play a crucial role in determining the measured threshold, suggesting that laboratory detectors may struggle to detect short-lived events. Numerical predictions also reveal how the thresholds linked to these events are affected by the degree of signal distortion.
- 13 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (10) , 5662-5669
Open AccessImpact of Distortion on the Multipactor Threshold for Dual Carrier Digitally Modulated Signals
Multipactor under digitally modulated signals is a field of growing interest in the space industry. The need to operate with higher powers arises from the industry demand to increase data throughput, enabled by advances in space-born amplifiers. However, this often leads to signal distortion, which may alter the multipactor threshold measured in laboratory conditions. This work aims to characterize, through the combination of experimental tests and numerical simulations, how distortion affects the multipactor performance of microwave devices excited by modulated signals. To this end, several dual carrier modulated signals with different distortion levels are digitally created, simulated, and tested on the same multipactor sample. When the simulation configuration matches the laboratory conditions, an excellent degree of accuracy is reported. However, simulations also demonstrate that the nonzero time response of the sensors may play a crucial role in determining the measured threshold, suggesting that laboratory detectors may struggle to detect short-lived events. Numerical predictions also reveal how the thresholds linked to these events are affected by the degree of signal distortion.
- Open Access
- 22 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (6) , 3177-3184
A Fast and Accurate Coarse Method for Multipactor Threshold Prediction of RF Filters Under Modulated Signal Excitation
Multipactor is a key high-power effect limiting the system performance for onboard satellite hardware. Although modern particle simulators admit arbitrary geometries and signals as inputs, their practical use is often limited to continuous-wave (CW) excitations. Unfortunately, the multipactor analysis for input-modulated signals normally leads to prohibitively large CPU times, as signal lengths are very large compared to the electron population’s evolution time. The Coarse Method is an elegant way of overcoming this limitation, providing a good estimate of the multipactor threshold in reduced CPU times. However, if the input signal is not preprocessed before being analyzed, the method is unable to account for the frequency dependence as it operates with electron dynamics information extracted at a single frequency, leading to biased predictions for narrowband samples as filters. This article proposes an extension to the original Coarse Method implementation by considering the sample response and the modulated signal spectral distribution to account for the frequency dependence. The resulting method is suitable for estimating the multipactor threshold of narrowband samples excited by modulated signals, while keeping the benefits in terms of simplicity, efficiency, and generality of the Coarse Method. The proposed approach is benchmarked against laboratory measurement results, as well as particle simulators and legacy Coarse Method predictions, revealing the advantages of the novel technique and its range of applications.
- 22 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (6) , 3177-3184
Open AccessA Fast and Accurate Coarse Method for Multipactor Threshold Prediction of RF Filters Under Modulated Signal Excitation
Multipactor is a key high-power effect limiting the system performance for onboard satellite hardware. Although modern particle simulators admit arbitrary geometries and signals as inputs, their practical use is often limited to continuous-wave (CW) excitations. Unfortunately, the multipactor analysis for input-modulated signals normally leads to prohibitively large CPU times, as signal lengths are very large compared to the electron population’s evolution time. The Coarse Method is an elegant way of overcoming this limitation, providing a good estimate of the multipactor threshold in reduced CPU times. However, if the input signal is not preprocessed before being analyzed, the method is unable to account for the frequency dependence as it operates with electron dynamics information extracted at a single frequency, leading to biased predictions for narrowband samples as filters. This article proposes an extension to the original Coarse Method implementation by considering the sample response and the modulated signal spectral distribution to account for the frequency dependence. The resulting method is suitable for estimating the multipactor threshold of narrowband samples excited by modulated signals, while keeping the benefits in terms of simplicity, efficiency, and generality of the Coarse Method. The proposed approach is benchmarked against laboratory measurement results, as well as particle simulators and legacy Coarse Method predictions, revealing the advantages of the novel technique and its range of applications.
- 19 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (6) , 3541-3551
Practical Determination of Passive Intermodulation From Modulated Signals in Satellite Applications
Passive intermodulation (PIM) measurements are typically conducted with a simplified test scenario composed of two radio frequency (RF) carrier tones operating in continuous wave (CW). However, satellite payloads tend to operate with a more complex scheme, where modulated signals are present at each transmission channel. This article aims at linking both PIM scenarios. A novel procedure is developed to obtain, from measured data obtained using two CW input tones, the spectral distribution and amplitude of a PIM contribution originated after exciting a nonlinear device with modulated signals. The technique determines the spectral distribution of the PIM term of interest from the spectrum of the input signals, and evaluates its amplitude from a recently formulated PIM power conservation rule. Moreover, an extensive PIM test campaign providing novel and valuable experimental data for the topic of PIM under modulated signal excitation has been carried out. The results obtained for a wide range of test scenarios exhibit a good agreement with theoretical predictions, thus providing a practical validation of the proposed technique.
- 19 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (6) , 3541-3551
Practical Determination of Passive Intermodulation From Modulated Signals in Satellite Applications
Passive intermodulation (PIM) measurements are typically conducted with a simplified test scenario composed of two radio frequency (RF) carrier tones operating in continuous wave (CW). However, satellite payloads tend to operate with a more complex scheme, where modulated signals are present at each transmission channel. This article aims at linking both PIM scenarios. A novel procedure is developed to obtain, from measured data obtained using two CW input tones, the spectral distribution and amplitude of a PIM contribution originated after exciting a nonlinear device with modulated signals. The technique determines the spectral distribution of the PIM term of interest from the spectrum of the input signals, and evaluates its amplitude from a recently formulated PIM power conservation rule. Moreover, an extensive PIM test campaign providing novel and valuable experimental data for the topic of PIM under modulated signal excitation has been carried out. The results obtained for a wide range of test scenarios exhibit a good agreement with theoretical predictions, thus providing a practical validation of the proposed technique.
- Open Access
- 23 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (10) , 5888-5895
Practical Characterization of the Effect of the Transmission Carrier Phases in Passive Intermodulation
The effect of the phase of the input carriers has been traditionally neglected in the characterization of passive intermodulation (PIM) since standard two-tone PIM tests seem to be unaffected by phase variations of the excitation signals. However, the phase of the input carriers can be of relevance in many practical applications. This article is aimed at filling this gap in the technical literature. First, the existing theory explaining why the phases do not affect the measured PIM contribution for a two-carrier excitation but can be of relevance for generic multicarrier scenarios is summarized. PIM measurements for complex signals composed of several carriers with varying phases are then reported, enabling the practical characterization of this effect for the first time. Experimental results of the test campaigns are fully aligned with theoretical predictions, thus allowing us to identify those PIM contributions that can be affected by the carrier phases and assess the expected variation range in their amplitude level.
- 23 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (10) , 5888-5895
Open AccessPractical Characterization of the Effect of the Transmission Carrier Phases in Passive Intermodulation
The effect of the phase of the input carriers has been traditionally neglected in the characterization of passive intermodulation (PIM) since standard two-tone PIM tests seem to be unaffected by phase variations of the excitation signals. However, the phase of the input carriers can be of relevance in many practical applications. This article is aimed at filling this gap in the technical literature. First, the existing theory explaining why the phases do not affect the measured PIM contribution for a two-carrier excitation but can be of relevance for generic multicarrier scenarios is summarized. PIM measurements for complex signals composed of several carriers with varying phases are then reported, enabling the practical characterization of this effect for the first time. Experimental results of the test campaigns are fully aligned with theoretical predictions, thus allowing us to identify those PIM contributions that can be affected by the carrier phases and assess the expected variation range in their amplitude level.
- Open Access
- 6 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (7) , 3051-3064
Remote Reconfiguration of Microwave Filters Using Dielectric Tuners
The objective of this article is to explore the use of dielectrics to reconfigure remotely microwave filters in rectangular waveguide. To start, we study experimentally the phase shift that is achievable using dielectric tuning elements in a rectangular waveguide. We then compare the results obtained with the performance of standard metallic tuning cylinders and screws. Next, the passive intermodulation (PIM) behavior of dielectric tuning elements is investigated experimentally. The PIM results obtained using dielectrics are then compared with the ones of metallic tuning elements. After that, the measured results for a filter tuned with a number of different dielectric tuning elements are discussed to identify the required relation between cavity size, dielectric constant, and tuner diameter. As a proof of concept, we then design, manufacture, and test two filters, one in WR75 and the other in WR90. Both simulated and measured results are then presented clearly demonstrating that the structures discussed can indeed be reconfigured (or tuned) both in terms of filter center frequency and bandwidth. Finally, computer-driven linear actuators are connected to the dielectric tuners, and the remote tuning capability is successfully demonstrated.
- 6 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (7) , 3051-3064
Open AccessRemote Reconfiguration of Microwave Filters Using Dielectric Tuners
The objective of this article is to explore the use of dielectrics to reconfigure remotely microwave filters in rectangular waveguide. To start, we study experimentally the phase shift that is achievable using dielectric tuning elements in a rectangular waveguide. We then compare the results obtained with the performance of standard metallic tuning cylinders and screws. Next, the passive intermodulation (PIM) behavior of dielectric tuning elements is investigated experimentally. The PIM results obtained using dielectrics are then compared with the ones of metallic tuning elements. After that, the measured results for a filter tuned with a number of different dielectric tuning elements are discussed to identify the required relation between cavity size, dielectric constant, and tuner diameter. As a proof of concept, we then design, manufacture, and test two filters, one in WR75 and the other in WR90. Both simulated and measured results are then presented clearly demonstrating that the structures discussed can indeed be reconfigured (or tuned) both in terms of filter center frequency and bandwidth. Finally, computer-driven linear actuators are connected to the dielectric tuners, and the remote tuning capability is successfully demonstrated.
- 1 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (6) , 675-678
A New Reference Sample for High-Frequency Multipactor Testing
Multipactor (MP) is a high-power effect severely limiting the performance of satellite communication links. A reference sample is normally used in the experimental setups for MP testing in order to verify its correct operation. However, the low gaps required for high frequencies jeopardize the manufacturability of the devices traditionally used for this purpose. A new reference sample, based on a stepped-impedance resonator (SIR), is proposed in this letter. The key design considerations are also outlined. A prototype operating between 17 and 18 GHz has been manufactured and tested, proving the novel structure allows higher gaps, and is, thus, suitable for higher frequency bands.
- 1 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (6) , 675-678
A New Reference Sample for High-Frequency Multipactor Testing
Multipactor (MP) is a high-power effect severely limiting the performance of satellite communication links. A reference sample is normally used in the experimental setups for MP testing in order to verify its correct operation. However, the low gaps required for high frequencies jeopardize the manufacturability of the devices traditionally used for this purpose. A new reference sample, based on a stepped-impedance resonator (SIR), is proposed in this letter. The key design considerations are also outlined. A prototype operating between 17 and 18 GHz has been manufactured and tested, proving the novel structure allows higher gaps, and is, thus, suitable for higher frequency bands.
- Open Access
- 10 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 152070-152074
A New Model to Determine Passive Intermodulation Terms When Non-Contributing Carriers are Added to Classical Scenarios
This paper provides a new theoretical model for the characterization of passive intermodulation behaviour when non-contributing carriers (i.e., carriers which do not directly affect the particular non-linear contribution under analysis) are added to classical two or three carriers scenarios. According to traditional models, the power of a particular passive intermodulation frequency term is only related to the contributing carriers which combines in non-linear way to generate this term, thus the presence of additional (i.e., non-contributing) carriers should not affect to the predicted power of such an intermodulation product. However, recent laboratory tests reveal that non-contributing carriers do reduce the power of unrelated passive intermodulation terms. A heuristic model is proposed in this work to explain this effect, which shows a good matching with measured results already published in the technical literature. The study is focused in third order non-linear contributions, as being the most critical in practical applications.
- 10 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 152070-152074
Open AccessA New Model to Determine Passive Intermodulation Terms When Non-Contributing Carriers are Added to Classical Scenarios
This paper provides a new theoretical model for the characterization of passive intermodulation behaviour when non-contributing carriers (i.e., carriers which do not directly affect the particular non-linear contribution under analysis) are added to classical two or three carriers scenarios. According to traditional models, the power of a particular passive intermodulation frequency term is only related to the contributing carriers which combines in non-linear way to generate this term, thus the presence of additional (i.e., non-contributing) carriers should not affect to the predicted power of such an intermodulation product. However, recent laboratory tests reveal that non-contributing carriers do reduce the power of unrelated passive intermodulation terms. A heuristic model is proposed in this work to explain this effect, which shows a good matching with measured results already published in the technical literature. The study is focused in third order non-linear contributions, as being the most critical in practical applications.
- 15 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 29 (10) , 659-661
Implementation of Waveguide Terminations With Low-Passive Intermodulation for Conducted Test Beds in Backward Configuration
This letter proposes a simple procedure to implement low-passive intermodulation (PIM) terminations in waveguide technology to measure conducted backward PIM. The procedure consists in inserting a filter before the waveguide termination of the test bench. This approach reduces the PIM contribution from the load and, consequently, lowers the residual PIM noise floor of the test bench. To validate the procedure, a conducted backward low-PIM setup working in K-band has been assembled and tested. The PIM performance improvement obtained fully confirms the validity of the proposed solution.
- 15 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 29 (10) , 659-661
Implementation of Waveguide Terminations With Low-Passive Intermodulation for Conducted Test Beds in Backward Configuration
This letter proposes a simple procedure to implement low-passive intermodulation (PIM) terminations in waveguide technology to measure conducted backward PIM. The procedure consists in inserting a filter before the waveguide termination of the test bench. This approach reduces the PIM contribution from the load and, consequently, lowers the residual PIM noise floor of the test bench. To validate the procedure, a conducted backward low-PIM setup working in K-band has been assembled and tested. The PIM performance improvement obtained fully confirms the validity of the proposed solution.