Jonathan Edward Evans
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jonathan Edward Evans has a total of 109 co-authors. Here are the top co-authors by number of shared publications:
- Alex M. Lord
Centre for Nanohealth, College of Engineering, University of Swansea, Singleton Park, SA2 8PP, United Kingdom
4 shared publications - Michael R. Jennings
Swansea University
4 shared publications Daniel R. Jones
College of Engineering , Swansea University, Swansea, UNITED KINGDOM OF GREAT BRITAIN AND NORTHERN IRELAND
3 shared publications- Owen James Guy
Swansea University
3 shared publications - Richard J. Cobley
Swansea University
3 shared publications - Soroush Faramehr
Centre for E-Mobility and Clean Growth (CECG), Coventry University, Coventry, U.K.
3 shared publications
Latest Publications
- 12 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 38 (4) , 758-764
High Voltage Design Strategies for Gallium Oxide Power Devices
This study employs drift-diffusion simulation to investigate key factors influencing the performance of β-Ga2O3 FinFETs, demonstrating that enhancement-mode behaviour (Vth 0) is achievable for β-Ga2O3 FinFET using a Fin width WFIN≤0.5 μm and doping concentration Nd≤1×101 cmtextsuperscript-. Breakdown voltage and output/transfer characteristics are calculated by using drift-diffusion methodology calibrated by experiments. We found that the metal work function (ms), dielectric constant (κ), and unintentional negative interface charge density (-Qf) at the β-Ga2O3/dielectric interface significantly impact Vth, with a high ms being necessary for enhancement mode (E-mode) operation. To achieve 5kV breakdown, a WFIN of 200 nm requires a fin thickness (TFIN) of 0.8 μm, a WFIN of 400 nm requires TFIN1.2 μm, and a WFIN 600 nm requires TFIN 2 μm. From WFIN of 200 nm to 400 nm, DIBL (drain induced barrier lowering, i.e. Vth /Vds) increases by 300%, while from 400 to 600 nm, it rises by only 100%. The presence of -Qf enhances the breakdown voltage by mitigating DIBL-related failure mechanisms and by redistributing the electric potential away from the gate dielectric and deeper into the β-Ga2O3 drift region. A controllable and relatively defect-free process was developed for Ga2O3 metal-insulator-semiconductor (MIS) structures, enabling improved interface quality. Capacitance–voltage measurements and progressive annealing studies demonstrate enhanced device stability and reduced hysteresis for the proposed FinFET application. Finally, an optimised β-Ga2O3 fin etch process was developed on the KLA SPTS SynapsEtchmodule for Ga2O3 technology integration.
- 12 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 38 (4) , 758-764
High Voltage Design Strategies for Gallium Oxide Power Devices
This study employs drift-diffusion simulation to investigate key factors influencing the performance of β-Ga2O3 FinFETs, demonstrating that enhancement-mode behaviour (Vth 0) is achievable for β-Ga2O3 FinFET using a Fin width WFIN≤0.5 μm and doping concentration Nd≤1×101 cmtextsuperscript-. Breakdown voltage and output/transfer characteristics are calculated by using drift-diffusion methodology calibrated by experiments. We found that the metal work function (ms), dielectric constant (κ), and unintentional negative interface charge density (-Qf) at the β-Ga2O3/dielectric interface significantly impact Vth, with a high ms being necessary for enhancement mode (E-mode) operation. To achieve 5kV breakdown, a WFIN of 200 nm requires a fin thickness (TFIN) of 0.8 μm, a WFIN of 400 nm requires TFIN1.2 μm, and a WFIN 600 nm requires TFIN 2 μm. From WFIN of 200 nm to 400 nm, DIBL (drain induced barrier lowering, i.e. Vth /Vds) increases by 300%, while from 400 to 600 nm, it rises by only 100%. The presence of -Qf enhances the breakdown voltage by mitigating DIBL-related failure mechanisms and by redistributing the electric potential away from the gate dielectric and deeper into the β-Ga2O3 drift region. A controllable and relatively defect-free process was developed for Ga2O3 metal-insulator-semiconductor (MIS) structures, enabling improved interface quality. Capacitance–voltage measurements and progressive annealing studies demonstrate enhanced device stability and reduced hysteresis for the proposed FinFET application. Finally, an optimised β-Ga2O3 fin etch process was developed on the KLA SPTS SynapsEtchmodule for Ga2O3 technology integration.
- Open Access
- 12 March 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (12) , 18996-19011
Large On–Off Enhancement of Au Nanocatalyst Contacts to ZnO Nanowires with Bulk and Surface Oxygen Modification
Schottky diodes have been a fundamental component of electrical circuits for many decades, and intense research continues to this day on planar materials with increasingly exotic compounds. With the birth of nanotechnology, a paradigm shift occurred with Schottky contacts proving to be essential for enabling nanodevice inventions and increasing their performance by many orders of magnitude, particularly in the fields of piezotronics and piezoelectric energy harvesting. ZnO nanomaterials have proven to be the most popular materials in those devices as they possess high piezoelectric coefficients, high surface sensitivity, and low resistivity due to the high native n-type doping and low hole concentration. ZnO nanowires grown by vapor phase techniques with the aid of a metal catalyst provide a ready-made epitaxial Schottky contact free from interfacial layers and major defects. We show here with the most comprehensive experimental investigation to-date of Au nanocontacts to ZnO nanowires that the modulation of bulk and surface oxygen can dramatically increase the rectifying quality of these contacts when applied in the metal-semiconductor-metal (M-S-M) device configuration with potential barriers approaching the performance of planar contacts on single crystal ZnO. Before modification, the Au-ZnO nanowire contacts in a rectifying-nanowire-ohmic M-S-M device configuration typically show limited current rectification and electrical transport properties dominated by surface effects and tunneling at the contact edge. Interestingly, the oxygen modulation only has a minor effect on the resistivity as the high-resolution cathodoluminescence spectroscopy shows that the dominant donors are In, Ga, and Al with no visible band emissions often associated with detrimental point defects. The spectroscopy also revealed that carbon is incorporated into the bulk that may present interesting magnetic properties for future spintronics applications. Atomic-resolution electron microscopy confirms the Zn-polar orientation of the high-quality single crystal nanowires used for the electrical measurements. X-ray photoelectron spectroscopy shows oxygen-annealed nanowires have fewer surface oxygen defects, and when that difference is coupled with a reduction in surface oxygen vacancies via oxygen plasma treatment, the current rectification can increase by several orders of magnitude with a much lower dispersion in the effective potential barrier properties when compared to those that are not annealed. This study concludes after the electrical measurements of 66 nanowire contacts/M-S-M structures with diameters as small as 25 nm using a scanning tunneling microscopy probe that effective device potential barrier heights of 0.65 eV and on-off ratios of 3 orders of magnitude can be achieved. Interestingly, this change in contact properties is transient in nature, revealing dynamic surface effects can govern the rectifying behavior and surface passivation techniques are desirable to achieve consistent performance. This work shows the overriding effects of surface defects and adsorbates on the sloping facets near the Au contact edge and the potential for this effect to be used to control the electrical transport properties and produce molecular-scale sensors to greatly enhance the performance of many piezotronic and energy harvesting devices.
- 12 March 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (12) , 18996-19011
Open AccessLarge On–Off Enhancement of Au Nanocatalyst Contacts to ZnO Nanowires with Bulk and Surface Oxygen Modification
Schottky diodes have been a fundamental component of electrical circuits for many decades, and intense research continues to this day on planar materials with increasingly exotic compounds. With the birth of nanotechnology, a paradigm shift occurred with Schottky contacts proving to be essential for enabling nanodevice inventions and increasing their performance by many orders of magnitude, particularly in the fields of piezotronics and piezoelectric energy harvesting. ZnO nanomaterials have proven to be the most popular materials in those devices as they possess high piezoelectric coefficients, high surface sensitivity, and low resistivity due to the high native n-type doping and low hole concentration. ZnO nanowires grown by vapor phase techniques with the aid of a metal catalyst provide a ready-made epitaxial Schottky contact free from interfacial layers and major defects. We show here with the most comprehensive experimental investigation to-date of Au nanocontacts to ZnO nanowires that the modulation of bulk and surface oxygen can dramatically increase the rectifying quality of these contacts when applied in the metal-semiconductor-metal (M-S-M) device configuration with potential barriers approaching the performance of planar contacts on single crystal ZnO. Before modification, the Au-ZnO nanowire contacts in a rectifying-nanowire-ohmic M-S-M device configuration typically show limited current rectification and electrical transport properties dominated by surface effects and tunneling at the contact edge. Interestingly, the oxygen modulation only has a minor effect on the resistivity as the high-resolution cathodoluminescence spectroscopy shows that the dominant donors are In, Ga, and Al with no visible band emissions often associated with detrimental point defects. The spectroscopy also revealed that carbon is incorporated into the bulk that may present interesting magnetic properties for future spintronics applications. Atomic-resolution electron microscopy confirms the Zn-polar orientation of the high-quality single crystal nanowires used for the electrical measurements. X-ray photoelectron spectroscopy shows oxygen-annealed nanowires have fewer surface oxygen defects, and when that difference is coupled with a reduction in surface oxygen vacancies via oxygen plasma treatment, the current rectification can increase by several orders of magnitude with a much lower dispersion in the effective potential barrier properties when compared to those that are not annealed. This study concludes after the electrical measurements of 66 nanowire contacts/M-S-M structures with diameters as small as 25 nm using a scanning tunneling microscopy probe that effective device potential barrier heights of 0.65 eV and on-off ratios of 3 orders of magnitude can be achieved. Interestingly, this change in contact properties is transient in nature, revealing dynamic surface effects can govern the rectifying behavior and surface passivation techniques are desirable to achieve consistent performance. This work shows the overriding effects of surface defects and adsorbates on the sloping facets near the Au contact edge and the potential for this effect to be used to control the electrical transport properties and produce molecular-scale sensors to greatly enhance the performance of many piezotronic and energy harvesting devices.
- Open Access
- 22 August 2024
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 359, 163-170
Demonstrating SiC In Situ Rounded Trench Processing Technologies for Future Power Trench MOSFET Applications
Effective control of device geometry is key to mitigating high localized electric fields in next-generation SiC power devices. Advanced trench processing allows for highly tunable trench-gate architectures in trench MOSFETs. By utilizing a two-step inductively coupled plasma reactive ion etch (ICP-RIE) process, a high degree of trench base corner rounding can be achieved, irrespective of trench opening corner geometry prior to post etch treatments. Sentaurus TCAD device modelling highlights the importance of effective electric field dispersion at the gate oxide using rounded trench corners, while I-V characterization of fabricated trench MOS-capacitor devices demonstrate the influence of trench base corner rounding on gate oxide breakdown.
- 22 August 2024
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 359, 163-170
Open AccessDemonstrating SiC In Situ Rounded Trench Processing Technologies for Future Power Trench MOSFET Applications
Effective control of device geometry is key to mitigating high localized electric fields in next-generation SiC power devices. Advanced trench processing allows for highly tunable trench-gate architectures in trench MOSFETs. By utilizing a two-step inductively coupled plasma reactive ion etch (ICP-RIE) process, a high degree of trench base corner rounding can be achieved, irrespective of trench opening corner geometry prior to post etch treatments. Sentaurus TCAD device modelling highlights the importance of effective electric field dispersion at the gate oxide using rounded trench corners, while I-V characterization of fabricated trench MOS-capacitor devices demonstrate the influence of trench base corner rounding on gate oxide breakdown.
- Open Access
- 19 May 2023
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 945, 61-66
Fabrication of Quasi-Vertical GaN-On-SiC Trench MOSFETs
We demonstrate quasi-vertical GaN MOSFETs fabricated on SiC substrates. The GaN epitaxial layers were grown via MOCVD on 100 mm 4H-SiC wafers, with the device structure consisting of a 2.5 μm drift layer and a Mg doped p-GaN body. The fabricated transistors exhibit normally-off characteristics, with low off-state leakage behavior and an on/off ratio of over . The specific on-resistance was measured to be which compares favorably to devices fabricated on other foreign substrates. Our results demonstrate an alternative substrate for realizing vertical GaN devices, which potentially offers better material quality and thermal properties compared with other foreign substrate choices.
- 19 May 2023
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 945, 61-66
Open AccessFabrication of Quasi-Vertical GaN-On-SiC Trench MOSFETs
We demonstrate quasi-vertical GaN MOSFETs fabricated on SiC substrates. The GaN epitaxial layers were grown via MOCVD on 100 mm 4H-SiC wafers, with the device structure consisting of a 2.5 μm drift layer and a Mg doped p-GaN body. The fabricated transistors exhibit normally-off characteristics, with low off-state leakage behavior and an on/off ratio of over . The specific on-resistance was measured to be which compares favorably to devices fabricated on other foreign substrates. Our results demonstrate an alternative substrate for realizing vertical GaN devices, which potentially offers better material quality and thermal properties compared with other foreign substrate choices.
- Open Access
- 20 April 2023
- Published by Wiley in Advanced Engineering Materials
- Vol. 25 (12)
A Low‐Temperature Batch Process for the Deposition of High‐Quality Conformal Alumina Thin Films for Electronic Applications
High‐quality, alumina thin films are extensively used as dielectrics, passivation layers, and barrier layers in electronics and many other applications. However, to achieve optimum stoichiometry and thus performance, the layers are often grown at elevated temperatures (>200 °C) using techniques such as atomic layer deposition (ALD). This is problematic for substrates or structures with low thermal budgets. Herein, alumina thin films are grown on 200 mm silicon substrates employing a versatile deposition method known as MVD at low deposition temperatures (35–150 °C). The chemical composition of the resulting films is investigated postdeposition using X‐ray photoelectron spectroscopy (XPS) and variable angle spectroscopic ellipsometry, with fully stoichiometric Al2O3 achieved at deposition temperatures as low as 100 °C. Dielectric measurements confirm outstanding dielectric properties compared to typical thermal ALD layers deposited at much higher temperatures. This low‐temperature deposition performance by considering the MVD reactor design and the “pump‐type” regime of precursor delivery versus the “flow‐type” regime of ALD is rationalized and understood. The results clearly demonstrate that alumina thin films grown with MVD are highly versatile for electronic applications and are of particular relevance and interest for the high‐volume processing of dielectric, passivation, and barrier layers at low temperatures.
- 20 April 2023
- Published by Wiley in Advanced Engineering Materials
- Vol. 25 (12)
Open AccessA Low‐Temperature Batch Process for the Deposition of High‐Quality Conformal Alumina Thin Films for Electronic Applications
High‐quality, alumina thin films are extensively used as dielectrics, passivation layers, and barrier layers in electronics and many other applications. However, to achieve optimum stoichiometry and thus performance, the layers are often grown at elevated temperatures (>200 °C) using techniques such as atomic layer deposition (ALD). This is problematic for substrates or structures with low thermal budgets. Herein, alumina thin films are grown on 200 mm silicon substrates employing a versatile deposition method known as MVD at low deposition temperatures (35–150 °C). The chemical composition of the resulting films is investigated postdeposition using X‐ray photoelectron spectroscopy (XPS) and variable angle spectroscopic ellipsometry, with fully stoichiometric Al2O3 achieved at deposition temperatures as low as 100 °C. Dielectric measurements confirm outstanding dielectric properties compared to typical thermal ALD layers deposited at much higher temperatures. This low‐temperature deposition performance by considering the MVD reactor design and the “pump‐type” regime of precursor delivery versus the “flow‐type” regime of ALD is rationalized and understood. The results clearly demonstrate that alumina thin films grown with MVD are highly versatile for electronic applications and are of particular relevance and interest for the high‐volume processing of dielectric, passivation, and barrier layers at low temperatures.
- Open Access
Status and Prospects of Cubic Silicon Carbide Power Electronics Device Technology
Wide bandgap (WBG) semiconductors are becoming more widely accepted for use in power electronics due to their superior electrical energy efficiencies and improved power densities. Although WBG cubic silicon carbide (3C-SiC) displays a modest bandgap compared to its commercial counterparts (4H-silicon carbide and gallium nitride), this material has excellent attributes as the WBG semiconductor of choice for low-resistance, reliable diode and MOS devices. At present the material remains firmly in the research domain due to numerous technological impediments that hamper its widespread adoption. The most obvious obstacle is defect-free 3C-SiC; presently, 3C-SiC bulk and heteroepitaxial (on-silicon) display high defect densities such as stacking faults and antiphase boundaries. Moreover, heteroepitaxy 3C-SiC-on-silicon means low temperature processing budgets are imposed upon the system (max. temperature limited to ~1400 °C) limiting selective doping realisation. This paper will give a brief overview of some of the scientific aspects associated with 3C-SiC processing technology in addition to focussing on the latest state of the art results. A particular focus will be placed upon key process steps such as Schottky and ohmic contacts, ion implantation and MOS processing including reliability. Finally, the paper will discuss some device prototypes (diodes and MOSFET) and draw conclusions around the prospects for 3C-SiC devices based upon the processing technology presented.
Open AccessStatus and Prospects of Cubic Silicon Carbide Power Electronics Device Technology
Wide bandgap (WBG) semiconductors are becoming more widely accepted for use in power electronics due to their superior electrical energy efficiencies and improved power densities. Although WBG cubic silicon carbide (3C-SiC) displays a modest bandgap compared to its commercial counterparts (4H-silicon carbide and gallium nitride), this material has excellent attributes as the WBG semiconductor of choice for low-resistance, reliable diode and MOS devices. At present the material remains firmly in the research domain due to numerous technological impediments that hamper its widespread adoption. The most obvious obstacle is defect-free 3C-SiC; presently, 3C-SiC bulk and heteroepitaxial (on-silicon) display high defect densities such as stacking faults and antiphase boundaries. Moreover, heteroepitaxy 3C-SiC-on-silicon means low temperature processing budgets are imposed upon the system (max. temperature limited to ~1400 °C) limiting selective doping realisation. This paper will give a brief overview of some of the scientific aspects associated with 3C-SiC processing technology in addition to focussing on the latest state of the art results. A particular focus will be placed upon key process steps such as Schottky and ohmic contacts, ion implantation and MOS processing including reliability. Finally, the paper will discuss some device prototypes (diodes and MOSFET) and draw conclusions around the prospects for 3C-SiC devices based upon the processing technology presented.
- Open Access
- 6 February 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (2) , 416
Assessing Surface Coverage of Aminophenyl Bonding Sites on Diazotised Glassy Carbon Electrodes for Optimised Electrochemical Biosensor Performance
Electrochemical biosensors using carbon-based electrodes are being widely developed for the detection of a range of different diseases. Since their sensitivity depends on the surface coverage of bioreceptor moieties, it necessarily depends on the surface coverage of amine precursors. Electrochemical techniques, using ferrocene carboxylic acid as a rapid and cheap assay, were used to assess the surface coverage of amino-phenyl groups attached to the carbon electrode. While the number of electrons transferred in the first step of diazotisation indicated a surface coverage of 8.02 ± 0.2 × l0−10 (mol/cm2), and those transferred in the second step, a reduction of nitrophenyl to amino-phenyl, indicated an amine surface coverage of 4–5 × l0−10 (mol/cm2), the number of electrons transferred during attachment of the amine coupling assay compound, ferrocene carboxylic acid, indicated a much lower available amine coverage of only 2.2 × l0−11 (mol/cm2). Furthermore, the available amine coverage was critically dependent upon the number of cyclic voltammetry cycles used in the reduction, and thus the procedures used in this step influenced the sensitivity of any subsequent sensor. Amine coupling of a carboxyl terminated anti-beta amyloid antibody specific to Aβ(1-42) peptide, a potential marker for Alzheimer’s disease, followed the same pattern of coverage as that observed with ferrocene carboxylic acid, and at optimum amine coverage, the sensitivity of the differential pulse voltammetry sensor was in the range 0–200 ng/mL with the slope of 5.07 µA/ng·mL−1 and R2 = 0.98.
- 6 February 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (2) , 416
Open AccessAssessing Surface Coverage of Aminophenyl Bonding Sites on Diazotised Glassy Carbon Electrodes for Optimised Electrochemical Biosensor Performance
Electrochemical biosensors using carbon-based electrodes are being widely developed for the detection of a range of different diseases. Since their sensitivity depends on the surface coverage of bioreceptor moieties, it necessarily depends on the surface coverage of amine precursors. Electrochemical techniques, using ferrocene carboxylic acid as a rapid and cheap assay, were used to assess the surface coverage of amino-phenyl groups attached to the carbon electrode. While the number of electrons transferred in the first step of diazotisation indicated a surface coverage of 8.02 ± 0.2 × l0−10 (mol/cm2), and those transferred in the second step, a reduction of nitrophenyl to amino-phenyl, indicated an amine surface coverage of 4–5 × l0−10 (mol/cm2), the number of electrons transferred during attachment of the amine coupling assay compound, ferrocene carboxylic acid, indicated a much lower available amine coverage of only 2.2 × l0−11 (mol/cm2). Furthermore, the available amine coverage was critically dependent upon the number of cyclic voltammetry cycles used in the reduction, and thus the procedures used in this step influenced the sensitivity of any subsequent sensor. Amine coupling of a carboxyl terminated anti-beta amyloid antibody specific to Aβ(1-42) peptide, a potential marker for Alzheimer’s disease, followed the same pattern of coverage as that observed with ferrocene carboxylic acid, and at optimum amine coverage, the sensitivity of the differential pulse voltammetry sensor was in the range 0–200 ng/mL with the slope of 5.07 µA/ng·mL−1 and R2 = 0.98.
- 21 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (11) , 4947-4952
Improvement of the Deep UV Sensor Performance of a β-Ga2O3 Photodiode by Coupling of Two Planar Diodes
β -Ga₂O₃ is one of the promising semiconductor materials that has been widely used in power electronics and ultraviolet (UV) detectors due to its wide bandgap and high sensitivity to UV light. Specifically, for the UV detection application, it has been reported that the photocurrent was in the scale of microamps (μA), which normally requires sophisticated signal processing units. In this work, a novel approach based upon coupling of two Schottky diodes is reported, leads to a substantial increase in photocurrent (~186 times) when benchmarked against a conventional planar UV photodiode. The detectivity and responsivity of the new device have also been significantly increased; the rectification ratio of this device was measured to be 1.7 x 10⁷ with ultralow dark current, when measured in the reverse bias. The results confirm that the approach of coupling two Schottky diodes has enormous potential for improving the optical performance of deep UV sensors.
- 21 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (11) , 4947-4952
Improvement of the Deep UV Sensor Performance of a β-Ga2O3 Photodiode by Coupling of Two Planar Diodes
β -Ga₂O₃ is one of the promising semiconductor materials that has been widely used in power electronics and ultraviolet (UV) detectors due to its wide bandgap and high sensitivity to UV light. Specifically, for the UV detection application, it has been reported that the photocurrent was in the scale of microamps (μA), which normally requires sophisticated signal processing units. In this work, a novel approach based upon coupling of two Schottky diodes is reported, leads to a substantial increase in photocurrent (~186 times) when benchmarked against a conventional planar UV photodiode. The detectivity and responsivity of the new device have also been significantly increased; the rectification ratio of this device was measured to be 1.7 x 10⁷ with ultralow dark current, when measured in the reverse bias. The results confirm that the approach of coupling two Schottky diodes has enormous potential for improving the optical performance of deep UV sensors.
- Open Access
- 10 September 2020
- Published by MDPI AG in Nanomaterials
- Vol. 10 (9) , 1808
A Facile Method for the Non-Covalent Amine Functionalization of Carbon-Based Surfaces for Use in Biosensor Development
Affinity biosensors based on graphene field-effect transistor (GFET) or resistor designs require the utilization of graphene’s exceptional electrical properties. Therefore, it is critical when designing these sensors, that the electrical properties of graphene are maintained throughout the functionalization process. To that end, non-covalent functionalization may be preferred over covalent modification. Drop-cast 1,5-diaminonaphthalene (DAN) was investigated as a quick and simple method for the non-covalent amine functionalization of carbon-based surfaces such as graphene, for use in biosensor development. In this work, multiple graphene surfaces were functionalized with DAN via a drop-cast method, leading to amine moieties, available for subsequent attachment to receptor molecules. Successful modification of graphene with DAN via a drop-cast method was confirmed using X-ray photoelectron spectroscopy (XPS), Raman spectroscopy and real-time resistance measurements. Successful attachment of receptor molecules also confirmed using the aforementioned techniques. Furthermore, an investigation into the effect of sequential wash steps which are required in biosensor manufacture, on the presence of the DAN layer, confirmed that the functional layer was not removed, even after multiple solvent exposures. Drop-cast DAN is thus, a viable fast and robust method for the amine functionalization of graphene surfaces for use in biosensor development.
- 10 September 2020
- Published by MDPI AG in Nanomaterials
- Vol. 10 (9) , 1808
Open AccessA Facile Method for the Non-Covalent Amine Functionalization of Carbon-Based Surfaces for Use in Biosensor Development
Affinity biosensors based on graphene field-effect transistor (GFET) or resistor designs require the utilization of graphene’s exceptional electrical properties. Therefore, it is critical when designing these sensors, that the electrical properties of graphene are maintained throughout the functionalization process. To that end, non-covalent functionalization may be preferred over covalent modification. Drop-cast 1,5-diaminonaphthalene (DAN) was investigated as a quick and simple method for the non-covalent amine functionalization of carbon-based surfaces such as graphene, for use in biosensor development. In this work, multiple graphene surfaces were functionalized with DAN via a drop-cast method, leading to amine moieties, available for subsequent attachment to receptor molecules. Successful modification of graphene with DAN via a drop-cast method was confirmed using X-ray photoelectron spectroscopy (XPS), Raman spectroscopy and real-time resistance measurements. Successful attachment of receptor molecules also confirmed using the aforementioned techniques. Furthermore, an investigation into the effect of sequential wash steps which are required in biosensor manufacture, on the presence of the DAN layer, confirmed that the functional layer was not removed, even after multiple solvent exposures. Drop-cast DAN is thus, a viable fast and robust method for the amine functionalization of graphene surfaces for use in biosensor development.
- 31 July 2020
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 124 (34) , 18777-18783
Enhancement of Multiwalled Carbon Nanotubes’ Electrical Conductivity Using Metal Nanoscale Copper Contacts and Its Implications for Carbon Nanotube-Enhanced Copper Conductivity
Herein we present an experimental/computational approach to probing the interaction between metal contacts and carbon nanotubes (CNTs) with regard creating the most efficient, low resistance, junction. Tungsten probes have been coated with copper or chromium and the efficiency of nano contact transport into multi-walled carbon nanotubes (MWCNTs) has been investigated experimentally, using scanning tunneling spectroscopy (STS) and nanoscale 2-point probe (2PP) I-V measurements, and in-silico, employing DFT calculations. Experimental I-V measurements suggest the relative conductivity of the metal-CNT interaction to be Cu > W > Cr. It has been found that copper contacting to MWCNTs results in a high density of state at the Fermi level, which contributes states to the conduction band. It was observed that the density of states also increased when chromium and tungsten probes were contacted to carbon nanotubes; however, in these cases the density of states increase would only contribute in high voltage/high temperature situations. This is demonstrated by an increase in the experimental electrical resistance when compared to the copper probe. These results suggest that in future copper tips should be used when carrying out all intrinsic conduction measurements on CNTs, and they also provide a rational for the ultra-conductivity of Cu-CNT and Cu-graphene composites
- 31 July 2020
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 124 (34) , 18777-18783
Enhancement of Multiwalled Carbon Nanotubes’ Electrical Conductivity Using Metal Nanoscale Copper Contacts and Its Implications for Carbon Nanotube-Enhanced Copper Conductivity
Herein we present an experimental/computational approach to probing the interaction between metal contacts and carbon nanotubes (CNTs) with regard creating the most efficient, low resistance, junction. Tungsten probes have been coated with copper or chromium and the efficiency of nano contact transport into multi-walled carbon nanotubes (MWCNTs) has been investigated experimentally, using scanning tunneling spectroscopy (STS) and nanoscale 2-point probe (2PP) I-V measurements, and in-silico, employing DFT calculations. Experimental I-V measurements suggest the relative conductivity of the metal-CNT interaction to be Cu > W > Cr. It has been found that copper contacting to MWCNTs results in a high density of state at the Fermi level, which contributes states to the conduction band. It was observed that the density of states also increased when chromium and tungsten probes were contacted to carbon nanotubes; however, in these cases the density of states increase would only contribute in high voltage/high temperature situations. This is demonstrated by an increase in the experimental electrical resistance when compared to the copper probe. These results suggest that in future copper tips should be used when carrying out all intrinsic conduction measurements on CNTs, and they also provide a rational for the ultra-conductivity of Cu-CNT and Cu-graphene composites