Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Hongfeng Xie has a total of 84 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Toughness effects and microscopic mechanisms of natural nanotube on epoxy asphalt

    by Xinpeng Cui, Chengwei Wu, Suzhou Cao, Haocheng Yang, Zhonghua Xi, Jun Cai, Junsheng Zhang, Hongfeng Xie


  • Open Access

    Dispersed and Co-Continuous Morphologies of Epoxy Asphalt Bond Coats and Their Effects on Mechanical Performance

    by Suzhou Cao, Haocheng Yang, Xinpeng Cui, Zhonghua Xi, Jun Cai, Junsheng Zhang, Hongfeng Xie

    The co-continuous microstructure represents an ideal configuration for polymer-modified asphalts. Consequently, determining the optimum polymer content hinges on establishing this critical network between polymer and bitumen. In this study, epoxy asphalt bond coats (EABCs) exhibiting three distinct morphologies (epoxy-dispersed, co-continuous, and bitumen-dispersed) were prepared. Phase structure evolution and the final cured morphology were analyzed using a laser scanning confocal microscope (LSCM). Rotational viscosity–time characteristics, tensile properties, single-lap shear strength, and pull-off adhesion strength were characterized using various techniques. Results indicated that the viscosity of EABCs at the late stage of the curing reaction increased with increasing epoxy resin (ER) concentration, whereas the time required for EABCs to reach a viscosity of 5 Pa·s decreased. LSCM analysis revealed that EABCs exhibited three distinct morphologies dependent on ER concentration: (1) a bitumen-continuous morphology with dispersed epoxy domains (41–42 vol.% ER) formed via a nucleation and growth mechanism; (2) a co-continuous structure (43–45 vol.% ER); and (3) an epoxy-continuous structure with dispersed bitumen domains (46 vol.% ER). Furthermore, the EABC with 42 vol.% exhibited a transitional morphology between bitumen-continuous and co-continuous structures. A significant improvement in mechanical properties occurred during the transition from the bitumen-continuous (41 vol.% ER) to the co-continuous morphology (43 vol.% ER): tensile strength, elongation at break, and toughness increased by 524%, 1298%, and 2732%, respectively. Simultaneously, pull-off adhesion strength and single-lap shear strength rose by 61% and 99%, respectively. In contrast, mechanical properties increased only gradually during the co-continuous phase and the subsequent transition to an epoxy-continuous morphology (45–46 vol.% ER). Considering cost, rotational viscosity–time dependence, and mechanical performance, an ER concentration of 43 vol.% (within the co-continuous region) is optimal for EABC production.


  • Open Access

    Viscosity, Morphology, and Thermomechanical Performance of Attapulgite-Reinforced Bio-Based Polyurethane Asphalt Composites

    by Haocheng Yang, Suzhou Cao, Xinpeng Cui, Zhonghua Xi, Jun Cai, Zuanru Yuan, Junsheng Zhang, Hongfeng Xie

    Bio-based polyurethane asphalt binder (PUAB) derived from castor oil (CO) is environmentally friendly and exhibits extended allowable construction time. However, CO imparts inherently poor mechanical performance to bio-based PUAB. To address this limitation, attapulgite (ATT) with fibrous nanostructures was incorporated. The effects of ATT on bio-based PUAB were systematically investigated, including cure kinetics, rotational viscosity (RV) evolution, phase-separation microstructures, dynamic mechanical properties, thermal stability, and mechanical performance. Experimental characterization employed Fourier transform infrared spectroscopy, Brookfield viscometry, laser scanning confocal microscopy, dynamic mechanical analysis, thermogravimetry, and tensile testing. ATT incorporation accelerated the polyaddition reaction conversion between isocyanate groups in polyurethane (PU) and hydroxyl groups in ATT. Paradoxically, it reduced RV during curing, prolonging allowable construction time proportionally with clay content. Additionally, ATT’s compatibilizing effect decreased bitumen particle size in PUAB, with scaling proportionally with clay loading. While enhancing thermal stability, ATT lowered the glass transition temperature and damping properties. Crucially, 1 wt% ATT increased tensile strength by 71% and toughness by 62%, while maintaining high elongation at break (>400%). The cost-effectiveness and significant reinforcement capability of ATT make it a promising candidate for producing high-performance bio-based PUAB composites.


  • Open Access

    Bio-Based Polyurethane Asphalt Binder with Continuous Polymer-Phase Structure: Critical Role of Isocyanate Index in Governing Thermomechanical Performance and Phase Morphology

    by Haocheng Yang, Suzhou Cao, Chengwei Wu, Zhonghua Xi, Jun Cai, Zuanru Yuan, Junsheng Zhang, Hongfeng Xie

    Polyurethane asphalt (PUA) has attracted considerable attention in the field of pavement engineering. However, traditional PUA systems typically exhibit low concentrations of polyurethane (PU), leading to a continuous bitumen-dominated phase that adversely affects mechanical properties. Furthermore, the non-renewable nature of raw materials raises environmental concerns. To address these limitations, this study developed an eco-friendly and cost-efficient bio-based PUA binder (PUAB) featuring a continuous high-biomass PU matrix (over 70% biomass) and a high bitumen content (60 wt%). The effects of the isocyanate index (NCO/OH ratio) on the cure kinetics, rheological behavior (rotational viscosity over time), viscoelasticity, damping capacity, phase morphology, thermal stability, and mechanical performance were systematically investigated using Fourier-transform infrared spectroscopy, dynamic mechanical analysis, laser-scanning confocal microscopy, and tensile testing. Key findings revealed that while the rotational viscosity of PUABs increased with a higher isocyanate index, all formulations maintained a longer allowable construction time. Specifically, the time to reach 1 Pa·s for all PUABs at 120 °C exceeded 60 min. During curing, higher isocyanate indices reduced final conversions but enhanced the storage modulus and glass transition temperatures, indicating improved rigidity and thermal resistance. Phase structure analysis demonstrated that increasing NCO/OH ratios reduced bitumen domain size while improving dispersion uniformity. Notably, the PUAB with the NCO/OH ratio of 1.3 achieved a tensile strength of 1.27 MPa and an elongation at break of 238%, representing a 49% improvement in toughness compared to the counterpart with an NCO/OH ratio = 1.1. These results demonstrate the viability of bio-based PUAB as a sustainable pavement material, offering a promising solution for environmentally friendly infrastructure development.


  • Open Access

    Isosorbide-Based Acrylic Pressure-Sensitive Adhesives Through UV-Cured Crosslinking with a Balance Between Adhesion and Cohesion

    by Jiajie Lv, Qingjun Wang, Hongfeng Xie

    The development of sustainable pressure-sensitive adhesives (PSAs) from natural biomass resources has attracted increasing attention owing to their non-toxic, biocompatible, and biodegradable features. In this study, a bio-based acrylic PSA with tunable adhesion and cohesion was synthesized by a selective chemical modification of isosorbide-5-acrylate (IA) and its copolymerization with butyl acrylate and acrylic acid through UV-curing crosslinking. During the UV-curing process, the synthesized isosorbide diacrylate ester (IDAE) served as the crosslinker, effectively improving the crosslinking degree of PSA. The impact of IA and IDAE on the mechanical properties of PSA was studied. Moreover, to achieve a balance between adhesion and cohesion, the optimal composition was identified. The addition of IA significantly enhances the stiffness of PSA. Furthermore, the combined effect of IA and IDAE improves the overall adhesion properties of the PSA. The optimal bio-based PSA demonstrates a peel force of 13.9 N/25 mm and a persistent time of 6820 min, promising to replace traditional petroleum-based PSAs.


  • Epoxy asphalt binder reinforced with waste polyethylene terephthalate (PET) for improving toughness

    by Chengwei Wu, Fan Jing, Haocheng Yang, Chenxuan Li, Zhonghua Xi, Jun Cai, Qingjun Wang, Hongfeng Xie


  • Open Access

    Thermo-Mechanical Properties and Phase-Separated Morphology of Warm-Mix Epoxy Asphalt Binders with Different Epoxy Resin Concentrations

    by Chengwei Wu, Haocheng Yang, Xinpeng Cui, Jun Cai, Zuanru Yuan, Junsheng Zhang, Hongfeng Xie

    The performance and phase-separated microstructures of epoxy asphalt binders greatly depend on the concentration of epoxy resin or bitumen. In this paper, the effect of the epoxy resin (ER) concentration (10–90%) on the viscosity, thermo-mechanical properties, and phase-separated morphology of warm-mix epoxy asphalt binders (WEABs) was investigated using the Brookfield rotational viscometer, differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and laser scanning confocal microscopy (LSCM). Due to the high reactivity of epoxy resin, the viscosity of WEABs increases with time. Furthermore, the initial viscosity of WEABs decreases with the ER concentration. Depending on the ER concentration, the viscosity–time behavior of WEABs is divided into three stages: slow (10–40%), fast (50–80%), and extremely slow (90%). In the slow stage, the viscosity slightly increases with the ER concentration, while the fast stage shows an opposite trend. DSC and DMA results reveal that WEABs with 10–80% ER exhibit two glass transition temperatures (Tgs) for cured epoxy resin and bitumen. Moreover, the Tgs of epoxy resin and bitumen increase with the ER concentration. However, WEAB with 90 % ER has only one Tg. LSCM observation shows that phase separation occurs in all WEABs. For WEABs containing 10–40% ER, spherical epoxy particles act as the discontinuous phase and disperse in the continuous bitumen phase. However, in WEABs with 50–90% ER, phase inversion takes place. Contrarily, bitumen particles disperse in the continuous epoxy phase. The damping properties of WEABs with the continuous epoxy phases increase with the ER concentration, while the crosslinking density shows an opposite trend. The occurrence of phase inversion results in a sharp increase in the tensile strength of WEABs. For WEABs with the continuous epoxy phases, the elongation at break increases with the ER concentration. The toughness first increases and then decreases with the ER concentration. A maximum toughness value shows at 70% ER.