Peng Gu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Interests
Peng Gu has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Dixian Zhao
Southeast University
24 shared publications - Xiaohu You
Southeast University
13 shared publications - Huiqi Liu
Chengdu Xphased Technology Company Ltd., Chengdu, China
6 shared publications - Jiajun Zhang
National Mobile Communication Research Laboratory, School of Information Science and Engineering, Southeast University, Nanjing, China
6 shared publications - Yongran Yi
National Mobile Communication Research Laboratory, School of Information Science and Engineering, Southeast University, Nanjing, China
6 shared publications Yuan Chai
Chengdu Xphased Technology Company Ltd., Chengdu, China
6 shared publications
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (10) , 5525-5537
A 300-GHz 2-D Scalable 4 × 4 Phased-Array Receiver With Half-Wavelength Element Spacing in 65-nm CMOS
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (10) , 5525-5537
A 300-GHz 2-D Scalable 4 × 4 Phased-Array Receiver With Half-Wavelength Element Spacing in 65-nm CMOS
- 8 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. PP (2156342X) , 1-8
A 0.31-THz 4×4 CMOS Phased-Array Receiver with 40°44° Beam Steering in E-/H-planes for Wireless Communication
In this paper, a planar 2-dimensional CMOS phased-array receiver (RX) working at 288$\mathit {-}$334 GHz is presented. This phased-array RX consists of 4×4 channels, with an antenna pitch of 0.52 $\boldsymbol{\lambda }\_{0}$. To address design challenges arising from the need to place large circuits around the small antenna array at these frequencies, the RX employs third-order subharmonic mixing for signal down-conversion, reducing the LO frequency and consequently lowering LO distribution losses as well as the area and power consumption of the LO generation circuits. Furthermore, the IF interconnection lines and LO distribution networks are implemented using a dual-layer scheme, which minimizes undesired coupling and leakage in the complex routing between the peripheral circuits surrounding the antenna array and the mixers located within the antenna array. To improve the receiver noise figure (NF) by controlling spurious products of the subharmonic mixer, a proposed antenna feeding structure provides the required impedance for the mixer at both RF and spurious harmonic frequencies. In the measurements, the RX scans over ±40$^\circ$/±44$^\circ$ in the E- and H-planes, respectively, and achieves a minimum single-sideband NF of 26.8 dB. A 6.4-cm, 307-GHz communication link, formed by the proposed RX chip and a commercial transmitter, demonstrates a 1.6-Gb/s data rate with an $\text{EVM}\_{\text{rms}}$ of 10.96% using 16-QAM waveforms. The power consumption is 1.877 W. To the best of our knowledge, this work presents the first silicon 2D phased-array RX above 300 GHz. Compared with prior works near 300 GHz, it achieves the smallest antenna pitch, the widest beam-steering range, the largest array size, and the lowest per-channel DC power consumption.
- 8 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. PP (2156342X) , 1-8
A 0.31-THz 4×4 CMOS Phased-Array Receiver with 40°44° Beam Steering in E-/H-planes for Wireless Communication
In this paper, a planar 2-dimensional CMOS phased-array receiver (RX) working at 288$\mathit {-}$334 GHz is presented. This phased-array RX consists of 4×4 channels, with an antenna pitch of 0.52 $\boldsymbol{\lambda }\_{0}$. To address design challenges arising from the need to place large circuits around the small antenna array at these frequencies, the RX employs third-order subharmonic mixing for signal down-conversion, reducing the LO frequency and consequently lowering LO distribution losses as well as the area and power consumption of the LO generation circuits. Furthermore, the IF interconnection lines and LO distribution networks are implemented using a dual-layer scheme, which minimizes undesired coupling and leakage in the complex routing between the peripheral circuits surrounding the antenna array and the mixers located within the antenna array. To improve the receiver noise figure (NF) by controlling spurious products of the subharmonic mixer, a proposed antenna feeding structure provides the required impedance for the mixer at both RF and spurious harmonic frequencies. In the measurements, the RX scans over ±40$^\circ$/±44$^\circ$ in the E- and H-planes, respectively, and achieves a minimum single-sideband NF of 26.8 dB. A 6.4-cm, 307-GHz communication link, formed by the proposed RX chip and a commercial transmitter, demonstrates a 1.6-Gb/s data rate with an $\text{EVM}\_{\text{rms}}$ of 10.96% using 16-QAM waveforms. The power consumption is 1.877 W. To the best of our knowledge, this work presents the first silicon 2D phased-array RX above 300 GHz. Compared with prior works near 300 GHz, it achieves the smallest antenna pitch, the widest beam-steering range, the largest array size, and the lowest per-channel DC power consumption.
- 25 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 36 (7) , 1132-1135
A Compact Low-Loss Variable Phase Shifter Using Phase Staggering All-Pass Network
The design of a compact low-loss phase shifter is presented in this letter. The superposition of all-pass network (APN) units with staggered phase responses allows expanded phase shift bandwidth and boosted phase shift range. The topology supports the wideband half-range phase shifting and a band-overlapped full-range phase shifting. The proof-of-concept phase shifter in 65-nm CMOS technology occupies a compact core area of 0.077 mm2 and achieves the 180°/90° phase shift range at 10–15/7–21 GHz with <1.1° rms phase error. The average insertion loss is 2.9–3.4 dB across 7–21 GHz, with a peak-to-peak gain error below ±0.35 dB. The low loss, low gain error, and compact size make the phase shifter suitable for phase control applications.
- 25 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 36 (7) , 1132-1135
A Compact Low-Loss Variable Phase Shifter Using Phase Staggering All-Pass Network
The design of a compact low-loss phase shifter is presented in this letter. The superposition of all-pass network (APN) units with staggered phase responses allows expanded phase shift bandwidth and boosted phase shift range. The topology supports the wideband half-range phase shifting and a band-overlapped full-range phase shifting. The proof-of-concept phase shifter in 65-nm CMOS technology occupies a compact core area of 0.077 mm2 and achieves the 180°/90° phase shift range at 10–15/7–21 GHz with <1.1° rms phase error. The average insertion loss is 2.9–3.4 dB across 7–21 GHz, with a peak-to-peak gain error below ±0.35 dB. The low loss, low gain error, and compact size make the phase shifter suitable for phase control applications.
- 21 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (6) , 4061-4072
A 24.25–29.5-GHz CMOS Upconversion Transmitter With Built-In Automatic LO Feedthrough and I/Q Imbalance Calibration for 5G New Radio
This paper presents a 24.25–29.5-GHz transmitter designed for fifth-generation (5G) millimeter-wave (mm-wave) applications, featuring a fully integrated self-calibration system for local oscillator feedthrough (LOFT) and in-phase/quadrature (I/Q) imbalance. The system incorporates an on-chip LOFT and image detection chain, together with a self-convergent digital control circuit. The existing on-chip calibration methods rely on Analog-to-Digital Converters (ADCs) to analyze the LOFT and image signals in the digital domain, or employ complex frequency-division circuits to down-convert the two impairments individually. However, these methods are confined to zero-IF or narrow-band low-IF systems, due to the limited bandwidth of the ADCs and frequency-division circuits. Furthermore, many existing approaches rely on external processing devices to implement the calibration algorithm, thereby increasing overall system complexity and operational burden. To overcome these limitations, the proposed architecture integrates a broadband detection chain that converts both LOFT and image signals into a unified DC output for high-sensitivity monitoring, which significantly extends the detection range. Subsequently, a fully built-in cyclic coordinate descent (CCD) algorithm jointly suppresses LOFT and image components, by autonomously optimizing the bias voltages of the mixer’s transconductance stage. Fabricated in 65-nm CMOS technology, the transmitter achieves a conversion gain of $7.5~\pm ~1.5$ dB across a wide IF bandwidth from 2.4 to 7.5 GHz, and delivers a maximum output 1-dB compression point (OP1dB) of 12.8 dBm. Post-calibration measurements reveal over 40-dB LOFT suppression and 47-dB image rejection ratio (IRR) across the operating bands. To the best of the authors’ knowledge, this work demonstrates the first reported fully integrated calibration system for joint LOFT and I/Q imbalance mitigation for 5G n257, n258, and n261 bands.
- 21 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (6) , 4061-4072
A 24.25–29.5-GHz CMOS Upconversion Transmitter With Built-In Automatic LO Feedthrough and I/Q Imbalance Calibration for 5G New Radio
This paper presents a 24.25–29.5-GHz transmitter designed for fifth-generation (5G) millimeter-wave (mm-wave) applications, featuring a fully integrated self-calibration system for local oscillator feedthrough (LOFT) and in-phase/quadrature (I/Q) imbalance. The system incorporates an on-chip LOFT and image detection chain, together with a self-convergent digital control circuit. The existing on-chip calibration methods rely on Analog-to-Digital Converters (ADCs) to analyze the LOFT and image signals in the digital domain, or employ complex frequency-division circuits to down-convert the two impairments individually. However, these methods are confined to zero-IF or narrow-band low-IF systems, due to the limited bandwidth of the ADCs and frequency-division circuits. Furthermore, many existing approaches rely on external processing devices to implement the calibration algorithm, thereby increasing overall system complexity and operational burden. To overcome these limitations, the proposed architecture integrates a broadband detection chain that converts both LOFT and image signals into a unified DC output for high-sensitivity monitoring, which significantly extends the detection range. Subsequently, a fully built-in cyclic coordinate descent (CCD) algorithm jointly suppresses LOFT and image components, by autonomously optimizing the bias voltages of the mixer’s transconductance stage. Fabricated in 65-nm CMOS technology, the transmitter achieves a conversion gain of $7.5~\pm ~1.5$ dB across a wide IF bandwidth from 2.4 to 7.5 GHz, and delivers a maximum output 1-dB compression point (OP1dB) of 12.8 dBm. Post-calibration measurements reveal over 40-dB LOFT suppression and 47-dB image rejection ratio (IRR) across the operating bands. To the best of the authors’ knowledge, this work demonstrates the first reported fully integrated calibration system for joint LOFT and I/Q imbalance mitigation for 5G n257, n258, and n261 bands.
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- p. 1-13
A 9.7-to-40.7-GHz Compact CMOS ×1/×2 Dual-Mode Frequency Multiplier Utilizing Magnetic-Decoupled Reconfigurable Transformer and Input-Reused Push-Push Topology
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- p. 1-13
A 9.7-to-40.7-GHz Compact CMOS ×1/×2 Dual-Mode Frequency Multiplier Utilizing Magnetic-Decoupled Reconfigurable Transformer and Input-Reused Push-Push Topology
- Open Access
- 22 November 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (12) , 1309
A Ka-Band CMOS Transmit/Receive Amplifier with Embedded Switch for Time-Division Duplex Applications
Time-division duplex (TDD) transceivers have found broad utility in millimeter-wave 5G communication, radar and imaging applications. The co-design of the switch and transmit/receive (T/R) amplifiers becomes essential in optimizing the passive loss and chip size. This work presents a Ka-band T/R amplifier with an embedded switch topology. The amplification cores from the TX and RX channels reuse the matching network to the T/R common port, and the full combination of switching and matching structures is enabled within a compact two-winding transformer. Implemented in 40 nm CMOS technology, the proof-of-concept Ka-band T/R amplifier occupies a core chip area of 0.163 mm2. Experimental results show that it achieves a peak gain of 17.2 dB with a −3 dB bandwidth of 22.6–30.2 GHz in TX mode and a peak of 17.1 dB with a −3 dB bandwidth of 23.4–31.0 GHz in RX mode. The compact size and wideband gain response make the proposed T/R amplifier suitable for Ka-band TDD applications.
- 22 November 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (12) , 1309
Open AccessA Ka-Band CMOS Transmit/Receive Amplifier with Embedded Switch for Time-Division Duplex Applications
Time-division duplex (TDD) transceivers have found broad utility in millimeter-wave 5G communication, radar and imaging applications. The co-design of the switch and transmit/receive (T/R) amplifiers becomes essential in optimizing the passive loss and chip size. This work presents a Ka-band T/R amplifier with an embedded switch topology. The amplification cores from the TX and RX channels reuse the matching network to the T/R common port, and the full combination of switching and matching structures is enabled within a compact two-winding transformer. Implemented in 40 nm CMOS technology, the proof-of-concept Ka-band T/R amplifier occupies a core chip area of 0.163 mm2. Experimental results show that it achieves a peak gain of 17.2 dB with a −3 dB bandwidth of 22.6–30.2 GHz in TX mode and a peak of 17.1 dB with a −3 dB bandwidth of 23.4–31.0 GHz in RX mode. The compact size and wideband gain response make the proposed T/R amplifier suitable for Ka-band TDD applications.
- 27 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (11) , 9632-9644
A 4.5–18-GHz CMOS Vector-Modulated Phase Shifter With Single-Stage Tunable Polyphase Filter and Built-In Automatic IQ-Vector Calibration Loop
This article presents a frequency-tunable CMOS vector-modulated phase shifter (VMPS) from 4.5 to 18 GHz. The design uses a single-stage tunable polyphase filter (PPF) with a built-in automatic calibration loop (BIACL), which adjusts the PPF resistance based on the detected amplitudes of the in-phase and quadrature (IQ) vectors to achieve center frequency calibration. The structurally optimized BIACL consists of amplitude detectors, a comparator, autocontrol logic, and a resistance digital-to-analog converter (RDAC). The amplitude detector, based on a Gilbert cell, achieves a 23-dB detection range with wide bandwidth and high sensitivity, offering enhanced performance in amplitude detection. For phase control, two independent cascode variable-gain amplifiers (VGAs) with tail-current switches are used for vector modulation. The VMPS is implemented in 65-nm CMOS technology, occupying a core chip area of 1.08 mm2. It demonstrates a wideband 6-bit 360° phase-shifting capability across 4.5–18 GHz with a calibration range from −14 to 2 dBm and achieves <2.3° rms phase error and <1.3-dB maximum gain error.
- 27 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (11) , 9632-9644
A 4.5–18-GHz CMOS Vector-Modulated Phase Shifter With Single-Stage Tunable Polyphase Filter and Built-In Automatic IQ-Vector Calibration Loop
This article presents a frequency-tunable CMOS vector-modulated phase shifter (VMPS) from 4.5 to 18 GHz. The design uses a single-stage tunable polyphase filter (PPF) with a built-in automatic calibration loop (BIACL), which adjusts the PPF resistance based on the detected amplitudes of the in-phase and quadrature (IQ) vectors to achieve center frequency calibration. The structurally optimized BIACL consists of amplitude detectors, a comparator, autocontrol logic, and a resistance digital-to-analog converter (RDAC). The amplitude detector, based on a Gilbert cell, achieves a 23-dB detection range with wide bandwidth and high sensitivity, offering enhanced performance in amplitude detection. For phase control, two independent cascode variable-gain amplifiers (VGAs) with tail-current switches are used for vector modulation. The VMPS is implemented in 65-nm CMOS technology, occupying a core chip area of 1.08 mm2. It demonstrates a wideband 6-bit 360° phase-shifting capability across 4.5–18 GHz with a calibration range from −14 to 2 dBm and achieves <2.3° rms phase error and <1.3-dB maximum gain error.
- 28 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (9) , 1178-1182
A Ka-Band Fully Integrated CMOS 1T3R Transceiver for Monopulse Radar Applications
Emerging low-altitude airspace economy has driven the development of high-resolution wireless sensors. Dedicated for the Ka-band monopulse radar applications, the design of a highly integrated 1T3R transceiver is detailed in this brief. The heterodyne transceiver incorporates full radio frequency (RF), intermediate frequency (IF) and local oscillator (LO) building blocks, supporting complete monopulse detection in azimuth and elevation. The calibration mode is introduced to enable system-level instant calibrations for enhanced detection accuracy. Dual injection style of the LO source facilitates the cascade of multiple chips for large-scale sensing systems. Fabricated in 65-nm CMOS technology and packaged with the wafer-level chip-scale packaging, the transceiver achieves the peak RX/TX gain of 18.4/33.2 dB across 32–36 GHz, with a minimum RX NF of 5.7 dB and peak saturated TX power of 15.6 dBm. The high integration level and flexible configuration of the transceiver make it suitable for Ka-band monopulse radar applications.
- 28 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (9) , 1178-1182
A Ka-Band Fully Integrated CMOS 1T3R Transceiver for Monopulse Radar Applications
Emerging low-altitude airspace economy has driven the development of high-resolution wireless sensors. Dedicated for the Ka-band monopulse radar applications, the design of a highly integrated 1T3R transceiver is detailed in this brief. The heterodyne transceiver incorporates full radio frequency (RF), intermediate frequency (IF) and local oscillator (LO) building blocks, supporting complete monopulse detection in azimuth and elevation. The calibration mode is introduced to enable system-level instant calibrations for enhanced detection accuracy. Dual injection style of the LO source facilitates the cascade of multiple chips for large-scale sensing systems. Fabricated in 65-nm CMOS technology and packaged with the wafer-level chip-scale packaging, the transceiver achieves the peak RX/TX gain of 18.4/33.2 dB across 32–36 GHz, with a minimum RX NF of 5.7 dB and peak saturated TX power of 15.6 dBm. The high integration level and flexible configuration of the transceiver make it suitable for Ka-band monopulse radar applications.
- 30 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (2) , 510-524
Packaged K-/Ka-Band Down/Up Frequency Converter Chipsets for Phased Array SATCOM Ground Terminals in 65-nm CMOS
Large-scale integrated phased arrays are enabling the millimeter-wave (mm-Wave) satellite communications (SATCOMs). Dedicated to the SATCOM planar phased array systems, the design of the K-/Ka-band down/up frequency converter (FC) chipsets is detailed in this article. The quadrature Gilbert FCs benefit from the proposed differentiated IF and LO high-order in-phase and quadrature (IQ) balancing techniques, supporting fully on-chip high-image/sideband rejection ratio (IRR/SRR). The wideband IF signal processing chains, simultaneously enabling gain control, reconfigurable filtering, Hilbert transformation, voltage/power amplifying, as well as single-ended/differential signal conversions, are proposed for the heterodyne up and down FCs, contributing to versatile and ready-to-use IF interfaces for various SATCOM modems in L and S bands. Power amplifying and buffering stages accompanied by gain control blocks are integrated to enhance the driving capability and dynamic range. In addition, the harmonic rejection quadrupler chain is adopted to relieve the high-frequency low-noise requirements on external LO sources and allow low-loss on-board routes. Fabricated in 65-nm CMOS technology and packaged with the wafer-level chip-scale packaging (WLCSP), the FC chipsets fully support the 2-D operation in the RF band of 17.7–21.2 GHz [downlink receiver (RX)]/27.5–31.0 GHz [uplink transmitter (TX)] and the wide-IF band of 0.8–4 GHz, offering the peak conversion gain of 35.7/33 dB for the RX/TX, with over 40-dBc IRR/SRR and 58-dBc calibrated LO suppression.
- 30 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (2) , 510-524
Packaged K-/Ka-Band Down/Up Frequency Converter Chipsets for Phased Array SATCOM Ground Terminals in 65-nm CMOS
Large-scale integrated phased arrays are enabling the millimeter-wave (mm-Wave) satellite communications (SATCOMs). Dedicated to the SATCOM planar phased array systems, the design of the K-/Ka-band down/up frequency converter (FC) chipsets is detailed in this article. The quadrature Gilbert FCs benefit from the proposed differentiated IF and LO high-order in-phase and quadrature (IQ) balancing techniques, supporting fully on-chip high-image/sideband rejection ratio (IRR/SRR). The wideband IF signal processing chains, simultaneously enabling gain control, reconfigurable filtering, Hilbert transformation, voltage/power amplifying, as well as single-ended/differential signal conversions, are proposed for the heterodyne up and down FCs, contributing to versatile and ready-to-use IF interfaces for various SATCOM modems in L and S bands. Power amplifying and buffering stages accompanied by gain control blocks are integrated to enhance the driving capability and dynamic range. In addition, the harmonic rejection quadrupler chain is adopted to relieve the high-frequency low-noise requirements on external LO sources and allow low-loss on-board routes. Fabricated in 65-nm CMOS technology and packaged with the wafer-level chip-scale packaging (WLCSP), the FC chipsets fully support the 2-D operation in the RF band of 17.7–21.2 GHz [downlink receiver (RX)]/27.5–31.0 GHz [uplink transmitter (TX)] and the wide-IF band of 0.8–4 GHz, offering the peak conversion gain of 35.7/33 dB for the RX/TX, with over 40-dBc IRR/SRR and 58-dBc calibrated LO suppression.