Huiqi Liu
Research Subjects
Huiqi Liu has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Dixian Zhao
Southeast University
8 shared publications - Peng Gu
Southeast University
6 shared publications - Yongran Yi
National Mobile Communication Research Laboratory, School of Information Science and Engineering, Southeast University, Nanjing, China
5 shared publications - Xiaohu You
Southeast University
4 shared publications Yuan Chai
Chengdu Xphased Technology Company Ltd., Chengdu, China
4 shared publications- Chenyu Xu
National Mobile Communications Research Laboratory, School of Information Science and Engineering, Southeast University, Nanjing, China
3 shared publications
Latest Publications
- 2 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. PP (2771957X) , 1-4
A Packaged Eight-Channel I/Q Receiver in 65-nm CMOS With Microstrip-to-Waveguide Transition for D-Band Applications
This letter presents a compact eight-channel direct-conversion I/Q receiver (RX) for D-band application. For area and power efficiency, one compact local oscillator (LO) multiplication and distribution network is shared by all channels. The in-channel building blocks are carefully optimized for I/Q amplitude-phase balance and overall performance improvement. Fabricated in 65-nm complementary metal–oxide–semiconductor (CMOS) with a fan-out wafer-level chip-scale packaging (WLCSP) process, the chip occupies a total area of 15.05 mm2. A microstrip-to-waveguide (WG) transition on the printed circuit board (PCB) is designed and measured, aiming to verify the packaging performance. The measured peak gain is 21.91 dB within the 3-dB bandwidth of 115–129.5 GHz. The measured double-sideband noise figure is 11.5–13.3 dB, and the image rejection is over 28 dBc. The RX consumes 674 mW during operation, including $8\times 71$ mW for eight channels and 106 mW for the common LO chain.
- 2 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. PP (2771957X) , 1-4
A Packaged Eight-Channel I/Q Receiver in 65-nm CMOS With Microstrip-to-Waveguide Transition for D-Band Applications
This letter presents a compact eight-channel direct-conversion I/Q receiver (RX) for D-band application. For area and power efficiency, one compact local oscillator (LO) multiplication and distribution network is shared by all channels. The in-channel building blocks are carefully optimized for I/Q amplitude-phase balance and overall performance improvement. Fabricated in 65-nm complementary metal–oxide–semiconductor (CMOS) with a fan-out wafer-level chip-scale packaging (WLCSP) process, the chip occupies a total area of 15.05 mm2. A microstrip-to-waveguide (WG) transition on the printed circuit board (PCB) is designed and measured, aiming to verify the packaging performance. The measured peak gain is 21.91 dB within the 3-dB bandwidth of 115–129.5 GHz. The measured double-sideband noise figure is 11.5–13.3 dB, and the image rejection is over 28 dBc. The RX consumes 674 mW during operation, including $8\times 71$ mW for eight channels and 106 mW for the common LO chain.
- 28 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (9) , 1178-1182
A Ka-Band Fully Integrated CMOS 1T3R Transceiver for Monopulse Radar Applications
Emerging low-altitude airspace economy has driven the development of high-resolution wireless sensors. Dedicated for the Ka-band monopulse radar applications, the design of a highly integrated 1T3R transceiver is detailed in this brief. The heterodyne transceiver incorporates full radio frequency (RF), intermediate frequency (IF) and local oscillator (LO) building blocks, supporting complete monopulse detection in azimuth and elevation. The calibration mode is introduced to enable system-level instant calibrations for enhanced detection accuracy. Dual injection style of the LO source facilitates the cascade of multiple chips for large-scale sensing systems. Fabricated in 65-nm CMOS technology and packaged with the wafer-level chip-scale packaging, the transceiver achieves the peak RX/TX gain of 18.4/33.2 dB across 32–36 GHz, with a minimum RX NF of 5.7 dB and peak saturated TX power of 15.6 dBm. The high integration level and flexible configuration of the transceiver make it suitable for Ka-band monopulse radar applications.
- 28 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (9) , 1178-1182
A Ka-Band Fully Integrated CMOS 1T3R Transceiver for Monopulse Radar Applications
Emerging low-altitude airspace economy has driven the development of high-resolution wireless sensors. Dedicated for the Ka-band monopulse radar applications, the design of a highly integrated 1T3R transceiver is detailed in this brief. The heterodyne transceiver incorporates full radio frequency (RF), intermediate frequency (IF) and local oscillator (LO) building blocks, supporting complete monopulse detection in azimuth and elevation. The calibration mode is introduced to enable system-level instant calibrations for enhanced detection accuracy. Dual injection style of the LO source facilitates the cascade of multiple chips for large-scale sensing systems. Fabricated in 65-nm CMOS technology and packaged with the wafer-level chip-scale packaging, the transceiver achieves the peak RX/TX gain of 18.4/33.2 dB across 32–36 GHz, with a minimum RX NF of 5.7 dB and peak saturated TX power of 15.6 dBm. The high integration level and flexible configuration of the transceiver make it suitable for Ka-band monopulse radar applications.
- 30 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (2) , 510-524
Packaged K-/Ka-Band Down/Up Frequency Converter Chipsets for Phased Array SATCOM Ground Terminals in 65-nm CMOS
Large-scale integrated phased arrays are enabling the millimeter-wave (mm-Wave) satellite communications (SATCOMs). Dedicated to the SATCOM planar phased array systems, the design of the K-/Ka-band down/up frequency converter (FC) chipsets is detailed in this article. The quadrature Gilbert FCs benefit from the proposed differentiated IF and LO high-order in-phase and quadrature (IQ) balancing techniques, supporting fully on-chip high-image/sideband rejection ratio (IRR/SRR). The wideband IF signal processing chains, simultaneously enabling gain control, reconfigurable filtering, Hilbert transformation, voltage/power amplifying, as well as single-ended/differential signal conversions, are proposed for the heterodyne up and down FCs, contributing to versatile and ready-to-use IF interfaces for various SATCOM modems in L and S bands. Power amplifying and buffering stages accompanied by gain control blocks are integrated to enhance the driving capability and dynamic range. In addition, the harmonic rejection quadrupler chain is adopted to relieve the high-frequency low-noise requirements on external LO sources and allow low-loss on-board routes. Fabricated in 65-nm CMOS technology and packaged with the wafer-level chip-scale packaging (WLCSP), the FC chipsets fully support the 2-D operation in the RF band of 17.7–21.2 GHz [downlink receiver (RX)]/27.5–31.0 GHz [uplink transmitter (TX)] and the wide-IF band of 0.8–4 GHz, offering the peak conversion gain of 35.7/33 dB for the RX/TX, with over 40-dBc IRR/SRR and 58-dBc calibrated LO suppression.
- 30 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (2) , 510-524
Packaged K-/Ka-Band Down/Up Frequency Converter Chipsets for Phased Array SATCOM Ground Terminals in 65-nm CMOS
Large-scale integrated phased arrays are enabling the millimeter-wave (mm-Wave) satellite communications (SATCOMs). Dedicated to the SATCOM planar phased array systems, the design of the K-/Ka-band down/up frequency converter (FC) chipsets is detailed in this article. The quadrature Gilbert FCs benefit from the proposed differentiated IF and LO high-order in-phase and quadrature (IQ) balancing techniques, supporting fully on-chip high-image/sideband rejection ratio (IRR/SRR). The wideband IF signal processing chains, simultaneously enabling gain control, reconfigurable filtering, Hilbert transformation, voltage/power amplifying, as well as single-ended/differential signal conversions, are proposed for the heterodyne up and down FCs, contributing to versatile and ready-to-use IF interfaces for various SATCOM modems in L and S bands. Power amplifying and buffering stages accompanied by gain control blocks are integrated to enhance the driving capability and dynamic range. In addition, the harmonic rejection quadrupler chain is adopted to relieve the high-frequency low-noise requirements on external LO sources and allow low-loss on-board routes. Fabricated in 65-nm CMOS technology and packaged with the wafer-level chip-scale packaging (WLCSP), the FC chipsets fully support the 2-D operation in the RF band of 17.7–21.2 GHz [downlink receiver (RX)]/27.5–31.0 GHz [uplink transmitter (TX)] and the wide-IF band of 0.8–4 GHz, offering the peak conversion gain of 35.7/33 dB for the RX/TX, with over 40-dBc IRR/SRR and 58-dBc calibrated LO suppression.
- Open Access
- 1 January 2025
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 61 (1)
A 26.5–29.5 GHz 256‐Element Dual‐Polarized Integrated Phased Array With 61‐dBm EIRP and 400‐MHz 64‐QAM Modulation
A dual‐polarized 256‐element integrated phased‐array antenna is presented, with an operating frequency range covering the 5G NR N257 band (i.e., 26.5–29.5 GHz). By adopting an integrated phased array technology with cost‐effective fabrication, multifunctional circuits can be implemented in high‐density configurations, thereby reducing system footprint without sacrificing performance. A design methodology for the dual‐polarized antennas with high isolation is employed to enhance the cross‐polarization suppression. The proposed phased array supports scanning angles of and in the azimuth and elevation planes, respectively. The typical effective isotropic radiated power (EIRP) of the dual‐polarized antenna is greater than 61 dBm with the 5G NR 400‐MHz 64‐QAM modulation (EVM 5.6).
- 1 January 2025
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 61 (1)
Open AccessA 26.5–29.5 GHz 256‐Element Dual‐Polarized Integrated Phased Array With 61‐dBm EIRP and 400‐MHz 64‐QAM Modulation
A dual‐polarized 256‐element integrated phased‐array antenna is presented, with an operating frequency range covering the 5G NR N257 band (i.e., 26.5–29.5 GHz). By adopting an integrated phased array technology with cost‐effective fabrication, multifunctional circuits can be implemented in high‐density configurations, thereby reducing system footprint without sacrificing performance. A design methodology for the dual‐polarized antennas with high isolation is employed to enhance the cross‐polarization suppression. The proposed phased array supports scanning angles of and in the azimuth and elevation planes, respectively. The typical effective isotropic radiated power (EIRP) of the dual‐polarized antenna is greater than 61 dBm with the 5G NR 400‐MHz 64‐QAM modulation (EVM 5.6).
- 5 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (2) , 776-789
Q/V-Band CMOS Beamforming ICs and Integrated Phased-Array Antennas
This paper presents 256-element transmitter (TX) and receiver (RX) phased arrays for satellite fixed communication at the Q and V bands, which integrate the phased-array antennas with eight-channel beamforming ICs. Wideband vector-modulated phase shifters (VGPS) and combinations of variable gain amplifier (VGA) and attenuators (ATT) are applied in the TX/RX beamforming ICs to achieve phase and gain tunings with large range and high precision. Based on the proposed beamforming ICs, the TX/RX phased arrays are realized with stacked aperture-coupled microstrip antennas on a cost-effective multi-layer PCB. Each array contains 32 TX/RX beamforming ICs, 256 antennas, and a 1-to-32 Wilkinson power divider/combiner networks. Fabricated in 65-nm CMOS technology, the packaged TX IC achieves an RMS gain error of 0.58 dB and an RMS phase error of 4.5 $^{\circ}$ with 78.5-mW dc power per channel, while the $\text{OP}_\text{1dB}$ is 9.6 dBm at 50.5 GHz. The packaged RX IC realizes a 5.3-dB NF, 0.47-dB RMS gain error, and 1.7 $^{\circ}$ RMS phase error with 24.2-mW dc power per channel. The Q/V-band phased arrays are capable of scanning $\pm$ 60 $^{\circ}$ , while the 256-element TX phased array achieves an EIRP of 63.5 dBm. Modulated signal measurements with 200-and 400-MHz QPSK, 16-QAM and 64-QAM are also provided.
- 5 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (2) , 776-789
Q/V-Band CMOS Beamforming ICs and Integrated Phased-Array Antennas
This paper presents 256-element transmitter (TX) and receiver (RX) phased arrays for satellite fixed communication at the Q and V bands, which integrate the phased-array antennas with eight-channel beamforming ICs. Wideband vector-modulated phase shifters (VGPS) and combinations of variable gain amplifier (VGA) and attenuators (ATT) are applied in the TX/RX beamforming ICs to achieve phase and gain tunings with large range and high precision. Based on the proposed beamforming ICs, the TX/RX phased arrays are realized with stacked aperture-coupled microstrip antennas on a cost-effective multi-layer PCB. Each array contains 32 TX/RX beamforming ICs, 256 antennas, and a 1-to-32 Wilkinson power divider/combiner networks. Fabricated in 65-nm CMOS technology, the packaged TX IC achieves an RMS gain error of 0.58 dB and an RMS phase error of 4.5 $^{\circ}$ with 78.5-mW dc power per channel, while the $\text{OP}_\text{1dB}$ is 9.6 dBm at 50.5 GHz. The packaged RX IC realizes a 5.3-dB NF, 0.47-dB RMS gain error, and 1.7 $^{\circ}$ RMS phase error with 24.2-mW dc power per channel. The Q/V-band phased arrays are capable of scanning $\pm$ 60 $^{\circ}$ , while the 256-element TX phased array achieves an EIRP of 63.5 dBm. Modulated signal measurements with 200-and 400-MHz QPSK, 16-QAM and 64-QAM are also provided.
- Top Cited Papers
- 30 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (10) , 3142-3155
K/Ka-Band Hybrid-Packaged Four-Element Four-Beam Phased-Array Transmitter and Receiver Front-Ends With Optimized Beamforming Passive Networks
This article presents K/Ka-band four-element four-beam phased-array transmitter (TX) and receiver (RX) front-ends. Hybrid-packaged technology is employed, consisting of one TX/RX 65-nm CMOS beamformer and four 0.1- $\mu$ m GaAs power amplifiers (PAs)/low-noise amplifiers (LNAs). Each beam maintains a full connection to every antenna element without degrading array gain. A compact and symmetrical layout floor-plan is proposed to reduce signal routing complexity. Signal distribution and combination are performed through two optimized tree-type and rectangular-shaped beamforming networks to improve the beam-to-beam consistency and isolation. The TX/RX CMOS beamformer provides an energy-efficient solution by adopting low-power phase/amplitude controls. The second harmonic trap is co-optimized with the transformer-based matching to enhance linearity in the TX. A new L-type inductor-enhanced matching network is devised in the RX to broaden bandwidth. In addition, the digital circuit introduces a voting mechanism to improve fault tolerance. Utilizing fan-out wafer-level chip-scale packaging, both hybrid-packaged TX and RX front-ends occupy an area of 50 mm $^\text{2}$ . The proposed TX demonstrates a measured small-signal gain of 23.5–26.5 dB across 17.7–20.2 GHz. The output 1-dB compression point ( $P_\text{1\,dB}$ ) and the maximal power-added efficiency (PAE $_\text{MAX}$ ) reach 21.2–23.2 dBm and 26%–30%, respectively. The proposed RX achieves a measured average gain of 24 dB across 27.5–30 GHz with a minimal noise figure (NF) of 3.1 dB. Both TX and RX exhibit uniform performance across all channels, while consuming a maximal power of 2600 and 264 mW, respectively, equivalent to 162.5–16.5 mW per element per beam.
- 30 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (10) , 3142-3155
Top Cited PapersK/Ka-Band Hybrid-Packaged Four-Element Four-Beam Phased-Array Transmitter and Receiver Front-Ends With Optimized Beamforming Passive Networks
This article presents K/Ka-band four-element four-beam phased-array transmitter (TX) and receiver (RX) front-ends. Hybrid-packaged technology is employed, consisting of one TX/RX 65-nm CMOS beamformer and four 0.1- $\mu$ m GaAs power amplifiers (PAs)/low-noise amplifiers (LNAs). Each beam maintains a full connection to every antenna element without degrading array gain. A compact and symmetrical layout floor-plan is proposed to reduce signal routing complexity. Signal distribution and combination are performed through two optimized tree-type and rectangular-shaped beamforming networks to improve the beam-to-beam consistency and isolation. The TX/RX CMOS beamformer provides an energy-efficient solution by adopting low-power phase/amplitude controls. The second harmonic trap is co-optimized with the transformer-based matching to enhance linearity in the TX. A new L-type inductor-enhanced matching network is devised in the RX to broaden bandwidth. In addition, the digital circuit introduces a voting mechanism to improve fault tolerance. Utilizing fan-out wafer-level chip-scale packaging, both hybrid-packaged TX and RX front-ends occupy an area of 50 mm $^\text{2}$ . The proposed TX demonstrates a measured small-signal gain of 23.5–26.5 dB across 17.7–20.2 GHz. The output 1-dB compression point ( $P_\text{1\,dB}$ ) and the maximal power-added efficiency (PAE $_\text{MAX}$ ) reach 21.2–23.2 dBm and 26%–30%, respectively. The proposed RX achieves a measured average gain of 24 dB across 27.5–30 GHz with a minimal noise figure (NF) of 3.1 dB. Both TX and RX exhibit uniform performance across all channels, while consuming a maximal power of 2600 and 264 mW, respectively, equivalent to 162.5–16.5 mW per element per beam.
- Top Cited Papers
- 8 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (1) , 409-423
A K-Band Hybrid-Packaged Temperature-Compensated Phased-Array Receiver and Integrated Antenna Array
This article presents an eight-channel 1.9-dB noise figure (NF) $K$ -band phased-array receiver (RX) for satellite communication (SATCOM). It employs the hybrid-packaged 65-nm CMOS beamformer and 0.1- $\mu$ m GaAs low-noise amplifiers (LNAs) based on the fan-out wafer-level chip-scale packaging (WLCSP) technology. For the power-efficient RX implementation, the power consumption of gain and phase tuning blocks is discussed, and the fully passive phase shifter (PS) and attenuator (ATT) are employed in this work. A global biasing scheme is proposed to ensure performance uniformity across temperature variations. Across the SATCOM band of 17.7–20.2 GHz, the proposed hybrid-packaged phased-array RX IC only consumes 30.2-mW dc power per channel and achieves $<$ 1.2-dB gain variation and $<$ 0.9-dB NF variation from $-$ 40 $^{\circ}$ to 85 $^{\circ}$ C. Based on the RX IC, a dual-polarized 1024-element RX antenna array is further introduced. The measured gain-to-noise temperature ratios (G/Ts) are 6.22 and 6.51 dB/K at 19.7 GHz for left-and right-hand circular polarizations, respectively.
- 8 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (1) , 409-423
Top Cited PapersA K-Band Hybrid-Packaged Temperature-Compensated Phased-Array Receiver and Integrated Antenna Array
This article presents an eight-channel 1.9-dB noise figure (NF) $K$ -band phased-array receiver (RX) for satellite communication (SATCOM). It employs the hybrid-packaged 65-nm CMOS beamformer and 0.1- $\mu$ m GaAs low-noise amplifiers (LNAs) based on the fan-out wafer-level chip-scale packaging (WLCSP) technology. For the power-efficient RX implementation, the power consumption of gain and phase tuning blocks is discussed, and the fully passive phase shifter (PS) and attenuator (ATT) are employed in this work. A global biasing scheme is proposed to ensure performance uniformity across temperature variations. Across the SATCOM band of 17.7–20.2 GHz, the proposed hybrid-packaged phased-array RX IC only consumes 30.2-mW dc power per channel and achieves $<$ 1.2-dB gain variation and $<$ 0.9-dB NF variation from $-$ 40 $^{\circ}$ to 85 $^{\circ}$ C. Based on the RX IC, a dual-polarized 1024-element RX antenna array is further introduced. The measured gain-to-noise temperature ratios (G/Ts) are 6.22 and 6.51 dB/K at 19.7 GHz for left-and right-hand circular polarizations, respectively.
- Top Cited Papers
- 5 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (9) , 2702-2718
A 24–29.5-GHz Highly Linear Phased-Array Transceiver Front-End in 65-nm CMOS Supporting 800-MHz 64-QAM and 400-MHz 256-QAM for 5G New Radio
This article presents a four-element phased-array transceiver (TRX) front-end for millimeter-wave (mm-Wave) 5G new radio (NR). The effects of amplitude-to-phase (AM–PM) and amplitude-to-amplitude (AM–AM) distortions on error vector magnitude (EVM) are detailed. A three-stage highly linear wideband class-AB power amplifier (PA) is described, mitigating AM–PM and AM–AM distortions without degrading other performances. A matching network embedded transmitting/receiving (T/R) switch is proposed to support time division duplex (TDD). With the proposed technique, RF switch insertion losses are reduced in both transmitter (TX) and receiving (RX) modes. In each TRX element, phase and gain controls are achieved by a 6-bit vector-modulated phase shifter (VMPS) with a phase tuning range of 360° and a 6-bit attenuator with a gain tuning range of 31.5 dB, respectively. Fabricated in 65-nm bulk CMOS, the proposed packaged TRX demonstrates the measured peak gains of 25.5/14.2 dB with the gain ripples of less than 2.5/1.9 dB across 24–29.5 GHz in the TX/RX mode. The measured peak $P_{\text {1 dB}}$ is 17.6 dBm with a power added efficiency (PAE) of 20.4%. The measured minimum noise figure (NF) is 4.3 dB. The TRX achieves an output power of 7.9–8.9 dBm and an EVM of −25 dB with 8 $\times $ 100-MHz 5G NR frequency range 2 (FR2) orthogonal frequency division multiplexing (OFDM) 64-quadrature amplitude modulation (QAM) signals across 24–29.5 GHz, covering 3rd generation partnership project (3GPP) 5G NR FR2 operating bands (i.e., n257, n258, and n261) around 26 GHz.
- 5 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (9) , 2702-2718
Top Cited PapersA 24–29.5-GHz Highly Linear Phased-Array Transceiver Front-End in 65-nm CMOS Supporting 800-MHz 64-QAM and 400-MHz 256-QAM for 5G New Radio
This article presents a four-element phased-array transceiver (TRX) front-end for millimeter-wave (mm-Wave) 5G new radio (NR). The effects of amplitude-to-phase (AM–PM) and amplitude-to-amplitude (AM–AM) distortions on error vector magnitude (EVM) are detailed. A three-stage highly linear wideband class-AB power amplifier (PA) is described, mitigating AM–PM and AM–AM distortions without degrading other performances. A matching network embedded transmitting/receiving (T/R) switch is proposed to support time division duplex (TDD). With the proposed technique, RF switch insertion losses are reduced in both transmitter (TX) and receiving (RX) modes. In each TRX element, phase and gain controls are achieved by a 6-bit vector-modulated phase shifter (VMPS) with a phase tuning range of 360° and a 6-bit attenuator with a gain tuning range of 31.5 dB, respectively. Fabricated in 65-nm bulk CMOS, the proposed packaged TRX demonstrates the measured peak gains of 25.5/14.2 dB with the gain ripples of less than 2.5/1.9 dB across 24–29.5 GHz in the TX/RX mode. The measured peak $P_{\text {1 dB}}$ is 17.6 dBm with a power added efficiency (PAE) of 20.4%. The measured minimum noise figure (NF) is 4.3 dB. The TRX achieves an output power of 7.9–8.9 dBm and an EVM of −25 dB with 8 $\times $ 100-MHz 5G NR frequency range 2 (FR2) orthogonal frequency division multiplexing (OFDM) 64-quadrature amplitude modulation (QAM) signals across 24–29.5 GHz, covering 3rd generation partnership project (3GPP) 5G NR FR2 operating bands (i.e., n257, n258, and n261) around 26 GHz.
- 5 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (6) , 768-771
A 1.9-dB NF K-Band Temperature-Healing Phased-Array Receiver Employing Hybrid Packaged 65-nm CMOS Beamformer and 0.1-μm GaAs LNAs
A 1.9-dB NF K-band phased-array receiver (RX) is presented, which employs the hybrid packaged 65-nm CMOS beamformer and 0.1- $\mu \text{m}$ GaAs LNAs based on the fan-out wafer-level chip-scale packaging (WLCSP) technology. Power-efficient gain and phase tuning blocks are utilized to reduce power consumption. Temperature-healing design methodology is adopted to ensure nearly constant gain response versus temperature variations. The proposed phased-array RX only consumes 30.2-mW dc power per channel and achieves < 1.2-dB gain variation and < 0.9-dB NF variation from −40 °C to 85 °C.
- 5 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (6) , 768-771
A 1.9-dB NF K-Band Temperature-Healing Phased-Array Receiver Employing Hybrid Packaged 65-nm CMOS Beamformer and 0.1-μm GaAs LNAs
A 1.9-dB NF K-band phased-array receiver (RX) is presented, which employs the hybrid packaged 65-nm CMOS beamformer and 0.1- $\mu \text{m}$ GaAs LNAs based on the fan-out wafer-level chip-scale packaging (WLCSP) technology. Power-efficient gain and phase tuning blocks are utilized to reduce power consumption. Temperature-healing design methodology is adopted to ensure nearly constant gain response versus temperature variations. The proposed phased-array RX only consumes 30.2-mW dc power per channel and achieves < 1.2-dB gain variation and < 0.9-dB NF variation from −40 °C to 85 °C.