Lucas Rafael Carneiro da Silva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Lucas Rafael Carneiro da Silva has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Renata Barbosa
Postgraduate Program in Materials Science and Engineering Federal University of Piauí (UFPI) Teresina Piauí Brazil
11 shared publications - Tatianny Soares Alves
Postgraduate Program in Materials Science and Engineering Federal University of Piauí (UFPI) Teresina Piauí Brazil
11 shared publications - Laura Hecker de Carvalho
Universidade Federal de Campina Grande, Brasil
5 shared publications - Ruth Marlene Campomanes Santana
Universidade Federal do Rio Grande do Sul, Brasil
5 shared publications - Alessandro de Oliveira Rios
Bioactive Compounds Laboratory, Food Science and Technology Institute Federal University of Rio Grande do Sul Porto Alegre Rio Grande do Sul Brazil
3 shared publications - Amanda Dantas de Oliveira
Graduate Program in Materials Science and Engineering (PPGCEM), Federal University of Pelotas (UFPel), Pelotas 96010-610, RS, Brazil
3 shared publications
Latest Publications
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 36 (2)
From filaments to membranes: additive manufacturing of Ecovio® for oil–water separation
This study explored Ecovio®-based filaments and 3D-printed membranes functionalized with zinc oxide (ZnO), biocide (BCD), and carnauba wax (CW) for gravity-driven oil–water separation. Filaments and membranes were produced via fused filament fabrication in grid and triangular geometries and characterized through melt flow index, water absorption, optical microscopy, contact angle, and separation performance. ZnO increased melt flow and long-term water absorption, whereas CW reduced water absorption and increased surface hydrophobicity. Optical microscopy revealed composition-dependent pore architectures ranging from ≈ 355 to 668 µm, directly affecting permeation behavior. Membranes delivered high permeation fluxes, exceeding 1.10 × 107 L·m−2·h−1 under gravity-driven operation. The integrated results showed that tailored filler combinations and infill geometries enable tunable hydrophilicity, porosity, and flux, establishing Ecovio® composites as a sustainable and viable platform for additive manufacturing of oil–water separation membranes.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 36 (2)
Open AccessFrom filaments to membranes: additive manufacturing of Ecovio® for oil–water separation
This study explored Ecovio®-based filaments and 3D-printed membranes functionalized with zinc oxide (ZnO), biocide (BCD), and carnauba wax (CW) for gravity-driven oil–water separation. Filaments and membranes were produced via fused filament fabrication in grid and triangular geometries and characterized through melt flow index, water absorption, optical microscopy, contact angle, and separation performance. ZnO increased melt flow and long-term water absorption, whereas CW reduced water absorption and increased surface hydrophobicity. Optical microscopy revealed composition-dependent pore architectures ranging from ≈ 355 to 668 µm, directly affecting permeation behavior. Membranes delivered high permeation fluxes, exceeding 1.10 × 107 L·m−2·h−1 under gravity-driven operation. The integrated results showed that tailored filler combinations and infill geometries enable tunable hydrophilicity, porosity, and flux, establishing Ecovio® composites as a sustainable and viable platform for additive manufacturing of oil–water separation membranes.
- 28 August 2025
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 36 (9)
Bio‐Based Strategies for Sustainable Packaging: Incorporation of Babassu Mesocarp Flour Into Poly(Lactic Acid) Films
The widespread use of non‐biodegradable plastics in food packaging has raised critical environmental concerns, driving the pursuit of sustainable alternatives. Poly(Lactic Acid) (PLA), a biodegradable thermoplastic derived from renewable resources, offers a promising option; however, researchers can mitigate its inherent limitations by incorporating natural fillers. This study evaluated the influence of Babassu Mesocarp Flour (BMF), an agro‐industrial by‐product (3, 5, 8, and 10 wt%), on the properties of PLA‐based films produced via flat‐die extrusion. BMF exhibited high starch content (66.23/100 g) and the predominance of amylopectin over amylose. The aerated and tapped bulk density was less than 1.0 g/mL. The study evaluated the physicochemical properties (water activity, pH, acidity, and soluble solids) and identified phenolic compounds, flavonoids, and monomeric anthocyanins in BMF. Its flow behavior was characterized by a Carr Index of 36.70% and a Hausner Ratio of 1.58. The color parameters reflected the natural coloration of the babassu fruit. Thermal analysis revealed a maximum decomposition temperature of 317°C. Water solubility and absorption capacity increased linearly with heating, and the damaged starch content was approximately 7%. The composite films revealed a uniform distribution and dispersion of the starch granules, a moisture content of less than 1.3%, high water resistance (< 0.25%), maximum water vapor permeability of 0.048 g.mm/Pa.h.m 2 , maximum tear resistance of ~1.2 N, and visible light transmittance of less than 40%. The BMF content significantly affected the films' color and gloss parameters. This approach values residual biomass and promotes eco‐friendly film development in line with circular economy principles.
- 28 August 2025
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 36 (9)
Bio‐Based Strategies for Sustainable Packaging: Incorporation of Babassu Mesocarp Flour Into Poly(Lactic Acid) Films
The widespread use of non‐biodegradable plastics in food packaging has raised critical environmental concerns, driving the pursuit of sustainable alternatives. Poly(Lactic Acid) (PLA), a biodegradable thermoplastic derived from renewable resources, offers a promising option; however, researchers can mitigate its inherent limitations by incorporating natural fillers. This study evaluated the influence of Babassu Mesocarp Flour (BMF), an agro‐industrial by‐product (3, 5, 8, and 10 wt%), on the properties of PLA‐based films produced via flat‐die extrusion. BMF exhibited high starch content (66.23/100 g) and the predominance of amylopectin over amylose. The aerated and tapped bulk density was less than 1.0 g/mL. The study evaluated the physicochemical properties (water activity, pH, acidity, and soluble solids) and identified phenolic compounds, flavonoids, and monomeric anthocyanins in BMF. Its flow behavior was characterized by a Carr Index of 36.70% and a Hausner Ratio of 1.58. The color parameters reflected the natural coloration of the babassu fruit. Thermal analysis revealed a maximum decomposition temperature of 317°C. Water solubility and absorption capacity increased linearly with heating, and the damaged starch content was approximately 7%. The composite films revealed a uniform distribution and dispersion of the starch granules, a moisture content of less than 1.3%, high water resistance (< 0.25%), maximum water vapor permeability of 0.048 g.mm/Pa.h.m 2 , maximum tear resistance of ~1.2 N, and visible light transmittance of less than 40%. The BMF content significantly affected the films' color and gloss parameters. This approach values residual biomass and promotes eco‐friendly film development in line with circular economy principles.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 35 (3)
Development of green composites based on bio-polyethylene and babassu mesocarp
Green composites are sustainable alternatives to conventional materials. This study developed composites based on bio-polyethylene (Bio-PE) and babassu mesocarp (BM) (1.5 and 3 phr), using PE-grafted maleic anhydride (PE-g-MA) (3 phr) as a compatibilizer. Materials were processed by extrusion and injection molding. BM exhibited starch-rich structure with a maximum degradation peak at 306 °C. PE-g-MA improved dispersion and surface finish, increasing the contact angle by up to 9.06%. Compared to neat Bio-PE, composites with PE-g-MA showed a 44.33% increase in yield stress and a 50.49% rise in ultimate tensile strength. Izod impact strength remained unchanged. Water absorption increased with BM, but was reduced up to 33.57% with PE-g-MA. This work introduces a novel use of BM in Bio-PE matrices, highlighting its potential as a Brazilian, renewable filler for sustainable composites.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 35 (3)
Open AccessDevelopment of green composites based on bio-polyethylene and babassu mesocarp
Green composites are sustainable alternatives to conventional materials. This study developed composites based on bio-polyethylene (Bio-PE) and babassu mesocarp (BM) (1.5 and 3 phr), using PE-grafted maleic anhydride (PE-g-MA) (3 phr) as a compatibilizer. Materials were processed by extrusion and injection molding. BM exhibited starch-rich structure with a maximum degradation peak at 306 °C. PE-g-MA improved dispersion and surface finish, increasing the contact angle by up to 9.06%. Compared to neat Bio-PE, composites with PE-g-MA showed a 44.33% increase in yield stress and a 50.49% rise in ultimate tensile strength. Izod impact strength remained unchanged. Water absorption increased with BM, but was reduced up to 33.57% with PE-g-MA. This work introduces a novel use of BM in Bio-PE matrices, highlighting its potential as a Brazilian, renewable filler for sustainable composites.
- Open Access
Natural Aging of Reprocessed Polypropylene Composites Filled with Sustainable Corn Fibers
Natural fiber reinforcements have the potential to enhance mechanical properties, thereby improving performance and durability in various applications. In this study, we comprehensively evaluated the impact of environmental degradation over 120 days on reprocessed polypropylene (PP) reinforced with corn husk fiber (CHF) composites. The manufactured systems underwent rigorous analysis using various techniques, including Fourier transform infrared spectroscopy, thermogravimetric analysis, optical microscopy, scanning electron microscopy, and tensile testing. These analyses revealed that climatic conditions significantly influenced (p < 0.05) the mechanical properties of all systems. Photodegradation led to surface morphological changes and chemical structures. Regardless, adding CHF filler proved a key factor, as it allowed for less susceptibility to environmental degradation than the reprocessed matrix. These findings, therefore, provide robust evidence supporting the feasibility of using CHF composites for manufacturing agricultural containers.
Open AccessNatural Aging of Reprocessed Polypropylene Composites Filled with Sustainable Corn Fibers
Natural fiber reinforcements have the potential to enhance mechanical properties, thereby improving performance and durability in various applications. In this study, we comprehensively evaluated the impact of environmental degradation over 120 days on reprocessed polypropylene (PP) reinforced with corn husk fiber (CHF) composites. The manufactured systems underwent rigorous analysis using various techniques, including Fourier transform infrared spectroscopy, thermogravimetric analysis, optical microscopy, scanning electron microscopy, and tensile testing. These analyses revealed that climatic conditions significantly influenced (p < 0.05) the mechanical properties of all systems. Photodegradation led to surface morphological changes and chemical structures. Regardless, adding CHF filler proved a key factor, as it allowed for less susceptibility to environmental degradation than the reprocessed matrix. These findings, therefore, provide robust evidence supporting the feasibility of using CHF composites for manufacturing agricultural containers.
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 34 (4) , e20240037
Production and characterization of pLA/PBAT-based films incorporated with natural and maleinized vegetable oils
This manuscript explored film production for food packaging using Ecovio® and natural additives (Babassu, Castor, and Cotton Vegetable Oil), emphasizing the oil’s maleinization to optimize compatibility with the polymer. The thermogravimetric analysis revealed variations in the maximum thermal decomposition temperature of maleinized vegetable oils (Thermal event II; natural oil to maleinized oil): from 402 to 338 °C (Babassu), 441 to 446 °C (Castor), and 413 to 430 °C (Cotton). The films were produced by casting, resulting in average thicknesses varying between 0.047 and 0.065 mm, and presented low surface defects. Optical micrographs showed that films with maleinized vegetable oil were more homogeneous due to maleic anhydride. Infrared spectroscopy showed that unsaturated fatty acid bonds affected the matrix and oil interaction. The presence of oils impacted the thermal stability, moisture content, and mechanical properties. This research promotes the use of renewable resources, contributing to the development of sustainable packaging.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 34 (4) , e20240037
Open AccessProduction and characterization of pLA/PBAT-based films incorporated with natural and maleinized vegetable oils
This manuscript explored film production for food packaging using Ecovio® and natural additives (Babassu, Castor, and Cotton Vegetable Oil), emphasizing the oil’s maleinization to optimize compatibility with the polymer. The thermogravimetric analysis revealed variations in the maximum thermal decomposition temperature of maleinized vegetable oils (Thermal event II; natural oil to maleinized oil): from 402 to 338 °C (Babassu), 441 to 446 °C (Castor), and 413 to 430 °C (Cotton). The films were produced by casting, resulting in average thicknesses varying between 0.047 and 0.065 mm, and presented low surface defects. Optical micrographs showed that films with maleinized vegetable oil were more homogeneous due to maleic anhydride. Infrared spectroscopy showed that unsaturated fatty acid bonds affected the matrix and oil interaction. The presence of oils impacted the thermal stability, moisture content, and mechanical properties. This research promotes the use of renewable resources, contributing to the development of sustainable packaging.
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 34 (1) , e20240009
Development by extrusion of composite films based on Poly(Lactic Acid)/Babassu Mesocarp Flour
The objective of this manuscript was to investigate the influence of different Babassu Mesocarp Flour (BMF) contents (3, 5, 8, and 10% by weight) on the physical and surface properties of the Poly(Lactic Acid) (PLA) matrix. For this purpose, composite films were produced through flat-die extrusion processing. Visual analysis showed that the films were successfully produced by this processing method and exhibited good handling. The physical properties of the films varied as follows: width (16.41‒20.38 cm), thickness (0.14‒0.24 mm), apparent density (0.78‒1.07 g/cm3), and grammage (168.34‒255.31 g/m2). Through optical microscopy, good distribution and dispersion of the particles were observed despite the presence of some agglomerates. The film surface became rough due to the incorporated flour content, which influenced the contact angle result. The combination of PLA/BMF for producing composite films has technological potential, enabling the valorization of an industrial by-product and preserving the environment.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 34 (1) , e20240009
Open AccessDevelopment by extrusion of composite films based on Poly(Lactic Acid)/Babassu Mesocarp Flour
The objective of this manuscript was to investigate the influence of different Babassu Mesocarp Flour (BMF) contents (3, 5, 8, and 10% by weight) on the physical and surface properties of the Poly(Lactic Acid) (PLA) matrix. For this purpose, composite films were produced through flat-die extrusion processing. Visual analysis showed that the films were successfully produced by this processing method and exhibited good handling. The physical properties of the films varied as follows: width (16.41‒20.38 cm), thickness (0.14‒0.24 mm), apparent density (0.78‒1.07 g/cm3), and grammage (168.34‒255.31 g/m2). Through optical microscopy, good distribution and dispersion of the particles were observed despite the presence of some agglomerates. The film surface became rough due to the incorporated flour content, which influenced the contact angle result. The combination of PLA/BMF for producing composite films has technological potential, enabling the valorization of an industrial by-product and preserving the environment.
- Open Access
- 5 April 2023
- Published by Macrothink Institute, Inc. in Journal of Food Industry
- Vol. 7 (1) , 24-53
Characterization of Babassu Mesocarp Flour as Potential Bio-Reinforcement for Poly(Lactic Acid)
Growing environmental concern has resulted in a strong trend towards using green materials, and the efficient use of by-products reduces resource waste and environmental pollution. Using Babassu Mesocarp Flour (BMF), a by-product of the babassu oil extraction industry, as bio-reinforcement for polymers, such as Poly (Lactic Acid) (PLA), is a promising alternative. Before any attempt to develop composite films, the industrially extracted BMF was characterized to know its chemical composition, particle size distribution, specific surface area, morphology, and structure, which is the main objective of this manuscript. The elemental analysis showed that the BMF is predominantly organic and also showed contents of inorganic elements by XRF. Its particles had an average diameter of 38.82 µm and a specific surface area of 3.02 m2/g. Through microscopic techniques, mainly SEM, starch granules in different shapes and sizes were observed. XRD and FTIR showed structure and functional groups typical of starchy materials, evidencing the ecological character of BMF. Progress is necessary to achieve the continuous and comprehensive use of babassu coconut by-products, mainly BMF, allowing greater appreciation. The characteristics of BMF are of great interest in PLA-based films, as they are green materials and non-toxic to the environment.
- 5 April 2023
- Published by Macrothink Institute, Inc. in Journal of Food Industry
- Vol. 7 (1) , 24-53
Open AccessCharacterization of Babassu Mesocarp Flour as Potential Bio-Reinforcement for Poly(Lactic Acid)
Growing environmental concern has resulted in a strong trend towards using green materials, and the efficient use of by-products reduces resource waste and environmental pollution. Using Babassu Mesocarp Flour (BMF), a by-product of the babassu oil extraction industry, as bio-reinforcement for polymers, such as Poly (Lactic Acid) (PLA), is a promising alternative. Before any attempt to develop composite films, the industrially extracted BMF was characterized to know its chemical composition, particle size distribution, specific surface area, morphology, and structure, which is the main objective of this manuscript. The elemental analysis showed that the BMF is predominantly organic and also showed contents of inorganic elements by XRF. Its particles had an average diameter of 38.82 µm and a specific surface area of 3.02 m2/g. Through microscopic techniques, mainly SEM, starch granules in different shapes and sizes were observed. XRD and FTIR showed structure and functional groups typical of starchy materials, evidencing the ecological character of BMF. Progress is necessary to achieve the continuous and comprehensive use of babassu coconut by-products, mainly BMF, allowing greater appreciation. The characteristics of BMF are of great interest in PLA-based films, as they are green materials and non-toxic to the environment.
- 6 February 2023
- Published by SAGE Publications in Polymers from Renewable Resources
- Vol. 14 (2) , 108-153
Polymer blends of poly(lactic acid) and starch for the production of films applied in food packaging: A brief review
The limited degradation of synthetic polymers used in food packaging when discarded in the environment is a major concern for society. Therefore, industry and academia have sought to develop biodegradable and eco-friendly materials for single-use in packaging. An interesting alternative for the food industry is biodegradable polymeric films, which is why different biopolymers have been used in the production of sustainable packaging. It is worth mentioning that the use of biodegradable polymers is one of the most successful innovations in the industry to address issues related to the environment. Among the available raw materials, starch extracted from different renewable sources is very promising for this purpose, due to its abundance, low-cost compared to other polymers and ability to produce non-toxic films. However, when used alone, pure starch has many limitations, which can be overcome by developing a mixture with other polymers (polymer blends), preferably from renewable and biodegradable sources, such as poly(lactic acid) (PLA). In this context, the absence of literature reviews evidencing the results of the application of films in foods led us to write this article, given the importance of polymer blends produced with different types of starch (cassava, corn, pea, potato, rice and wheat) and the PLA matrix. According to the results, it is clear that polymer blends based on PLA/Starch for food packaging are very promising, already being part of the industries solutions, aiming to minimize the large volume of plastic waste of petrochemical origin discarded in nature. Obviously, as with any technology, more research is needed to further improve the performance of the films, and while much research has made great strides, there are still limitations that prevent the commercialization of these materials.
- 6 February 2023
- Published by SAGE Publications in Polymers from Renewable Resources
- Vol. 14 (2) , 108-153
Polymer blends of poly(lactic acid) and starch for the production of films applied in food packaging: A brief review
The limited degradation of synthetic polymers used in food packaging when discarded in the environment is a major concern for society. Therefore, industry and academia have sought to develop biodegradable and eco-friendly materials for single-use in packaging. An interesting alternative for the food industry is biodegradable polymeric films, which is why different biopolymers have been used in the production of sustainable packaging. It is worth mentioning that the use of biodegradable polymers is one of the most successful innovations in the industry to address issues related to the environment. Among the available raw materials, starch extracted from different renewable sources is very promising for this purpose, due to its abundance, low-cost compared to other polymers and ability to produce non-toxic films. However, when used alone, pure starch has many limitations, which can be overcome by developing a mixture with other polymers (polymer blends), preferably from renewable and biodegradable sources, such as poly(lactic acid) (PLA). In this context, the absence of literature reviews evidencing the results of the application of films in foods led us to write this article, given the importance of polymer blends produced with different types of starch (cassava, corn, pea, potato, rice and wheat) and the PLA matrix. According to the results, it is clear that polymer blends based on PLA/Starch for food packaging are very promising, already being part of the industries solutions, aiming to minimize the large volume of plastic waste of petrochemical origin discarded in nature. Obviously, as with any technology, more research is needed to further improve the performance of the films, and while much research has made great strides, there are still limitations that prevent the commercialization of these materials.
- Open Access
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 25
Physical, Morphological, Structural, Thermal and Antimicrobial Characterization of Films based on Poly(Lactic Acid), Organophilic Montmorillonite and Oregano Essential Oil
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 25
Open AccessPhysical, Morphological, Structural, Thermal and Antimicrobial Characterization of Films based on Poly(Lactic Acid), Organophilic Montmorillonite and Oregano Essential Oil
- Open Access
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 24 (4)
Effect of Reprocessing Cycles on the Morphology and Mechanical Properties of a Poly(Propylene)/Poly(Hydroxybutyrate) Blend and its Nanocomposite
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 24 (4)
Open AccessEffect of Reprocessing Cycles on the Morphology and Mechanical Properties of a Poly(Propylene)/Poly(Hydroxybutyrate) Blend and its Nanocomposite