OPOleksii Pedash

Oleksii Pedash

*This is an algorithmically generated author record based on publicly available information.

Oleksii Pedash has a total of 49 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Enhancing oxidation and corrosion performance of laser PBF Inconel 718 alloy by thermomechanical post-treatment induced structural-phase rearrangement and surface nanocrystallization

    by Dmytro Lesyk, Bohdan Mordyuk, Indrajit Charit, Krishnan Raja, Maksym Lytvynenko, Andrii Tyshchenko, Oleksii Pedash, Andrii Kotko, Aitzol Lamikiz

    Inconel 718 test specimens were manufactured using a laser powder bed fusion (LPBF) additive manufacturing method, which is a promising technology for producing superalloy end-products with complex shapes for aerospace applications. To enhance the operational properties of the Inconel 718 alloy parts manufactured by the LPBF process, a combined thermomechanical post-treatment was applied in this work, which included hot isostatic pressing (HIP), heat treatment (homogenization annealing combined with double aging), and surface shot peening (SP). The variation in microstructure and high-temperature performance during exposure to air oxidation at 650 °C for 40 h was compared for the LPBF-manufactured Inconel 718 alloy specimens with various heat treatment conditions and surface severe plastic deformation (SPD) by SP. Studies using X-ray diffraction (XRD) and transmission electron microscopy (TEM) revealed the microstructure and phase state formed after thermomechanical post-processing, which provides the increased surface hardness of LPBF samples. The heat treatments (HIP → annealing → aging (HIPHA) and HIP → aging (HIPA)) increase the oxidation resistance. However, homogenization-induced grain growth in the HIPHA process results in a lower anti-oxidation resistance enhancement than that after the HIPA heat treatment. Further surface SPD post-processing by the SP significantly improves the oxidation resistance owing to the accelerated formation of protective chromium-enriched scales that were favoured by the SPD-induced nanostructure in the near-surface layers of LPBF samples. The corrosion resistance in a 3.5% solution of sodium chloride was also improved after both thermal treatments applied after HIP and SP-finishing applied after thermal post-treatments.


  • Additive Manufacturing in the Production of Aircraft Parts

    by Oleksii Pedash, Valeriy Naumyk, Pavlo Kasay, Yevhen Milonin, Serhii Chigileychyk

  • Complex modification of heat-resistant ZhS3DK-V1 alloy with itrii and titanium carbonitride and niobium

    by Zaporizhzhia Zaporozhye Machine-Building Plant Them. V.I. Omelchenko, D. О. Tomkin, О. О. Pedash, Zaporizhzhia Motor Sich Jsc, О. О. Naumyk, V. V. Naumyk

    Samples cast from heat-resistant ZhS3DK-VI nickel alloy modified with yttrium in combination with titanium carbonitride or niobium were studied. It is found that the chemical composition of the samples is satisfactory and meets the requirements of OST 1.90.126-85. Heat resistance, strength and ductility characteristics of the studied samples after hot isostatic pressing and standard heat treatment meet the regulatory requirements. The impact toughness value for the alloy with niobium content is slightly lower than the developer requirements, but is within the regulatory standards. In the microstructure of the alloy with titanium carbonitride, the grain boundaries are mainly thin with the presence of carbides with a size not exceeding 4mμ, as well as carbonitrides in the form of globular clusters near the grain boundaries. As for the alloy with niobium, the grain boundaries are coarser due to the release of carbonitrides up to 7mμ in size, as well as plate-like carbides up to 10mμ long. Thus, complex modification with yttrium and titanium carbonitride ensures the formation of a more favorable structure and significantly improves mechanical and heat-resistant properties of the ZhS3DK-VI nickel alloy.

  • Open Access

    INFLUENCE OF REDUCED CARBON CONTENT ON THE PROPERTIES OF ZHS3DK-VI ALLOY

    by Zaporizhzhya Machine-Building Plant Named After V.I. Omelchenko, Dmytro Tomkin, Oleksii Pedash, Joint Stock Company «Motor Sich», Olena Naumyk, National University «Zaporizhzhia Polytechnic», Valeriy Naumyk

    The effect of reduced carbon content (0.015...0.020 % С) and, accordingly, the carbide phase on the properties of ЖС3ДК-ВІ alloy with additional alloying and modification with niobium, hafnium-nickel and nickel-yttrium alloys was investigated. It was established that in the structure of test samples with reduced carbon content, carbides are practically absent, and grain boundaries are very thin. When niobium, yttrium and hafnium are introduced, carbides are formed in the form of globular particles mostly uniformly distributed in the volume of the metal. The microstructure of samples with reduced carbon content is coarsely crystalline, which is probably due to the absence of competitive phase growth during melt crystallization. Experimental variants with low carbon content have impact toughness values at the level of 90...150 J/cm2, but extremely low long-term strength, probably due to the lack of carbide strengthening in the alloy. High impact toughness values are associated with the uniform distribution of the finely dispersed carbonitride phase in the structure. Complex modified (Nb+Hf+Y) samples, with a carbon content of 0.06%, showed sufficient impact toughness and long-term strength, which significantly exceeded the requirements of OST 1.90126-85. In these samples, the almost complete absence of large carbides in the bulk of the main γ-solid solution grains and the presence of small carbides of the Me23C6 type, which were released during heat treatment along the grain boundaries, prevented grain boundary slippage under conditions of high temperatures and applied load. The level of impact toughness, in this case, is provided by the release and uniform distribution of discrete and globular carbides and carbonitrides (approximately 2...3 µm in size) during the treatment of the melt with yttrium and hafnium. The decrease in impact strength, compared to low-carbon options, is probably due to the release of double carbides of font morphology. Досліджено вплив зниженого вмісту вуглецю (0,015…0,020 % С) та, відповідно, карбідної фази на властивості сплаву ЖС3ДК-ВІ з додатковим легуванням та модифікуванням ніобієм, лігатурами гафній-нікель та нікель-ітрій. Встановлено, що у структурі дослідних зразків зі зниженим вмістом вуглецю карбіди практично відсутні, а межі зерен дуже тонкі. При введенні ніобію, ітрію та гафнію відбувається утворення карбідів у формі глобулярних частинок, в основному рівномірно розподілених в об’ємі металу. Мікроструктура зразків зі зниженим вмістом вуглецю крупно кристалічна, що, ймовірно, зумовлено відсутністю конкурентного фазового росту при кристалізації розплаву. Дослідні варіанти з низьким вмістом вуглецю мають значення ударної в’язкості на рівні 90…150 Дж/см2, але вкрай низьку тривалу міцність, мабуть, через відсутність карбідного зміцнення у сплаві. Високі показники ударної в’язкості пов’язані з рівномірним розподілом у структурі дрібнодисперсної карбонітридної фази. Комплексно модифіковані (Nb+Hf+Y) зразки із вмістом вуглецю 0,06 %, показали достатню ударну в’язкість і тривалу міцність, що значно перевищувало вимоги ОСТ 1.90126-85. У цих зразках практично повністю відсутні великі карбіди в об’ємі зерен основного γ-твердого розчину і наявні дрібні карбіди типу Ме23С6, що виділилися в процесі термічної обробки по межах зерен, перешкоджали зернограничному прослизанню в умовах високих температур і прикладеного навантаження. Рівень ударної в’язкості в даному випадку забезпечується виділенням і рівномірним розподілом дискретних і глобулярних карбідів та карбонітридів (розміром приблизно 2...3 мкм) при обробці розплаву ітрієм і гафнієм. Зниження ударної в’язкості, порівняно з варіантами з низьким вмістом вуглецю, ймовірно, пов’язане з виділенням подвійних карбідів шрифтової морфології.


  • Investigation of Zhs3dk-VI Alloy as a Material of Gas Turbine Engine Cast Blades

    by Dmytro Tomkin, Oleksii Pedash, Olena Naumyk, Valeriy Naumyk, Eduard Kondratiuk


  • Open Access

    COMPLEX MODIFICATION OF NICKEL-BASED SUPERALLOY WITH ULTRA-FINE REFRACTORY COMPOUNDS PARTICLE

    by Serhii Danylov, Oleksii Pedash, Valeriy Naumyk, Dmytro Tomkin, Olena Naumyk, Сергій Данилов, Валерій Наумик, Дмитро Тьомкін

    Purpose. Due to the complex modification of nickel-based superalloy with modifiers of different mechanisms of action, it is possible to increase the characteristics of plasticity and impact strength to a level that will allow to localize the possible destruction of large-sized blades of a low-pressure turbine of an aircraft engine during operation cycle. Research methods. Microstructure analysis and phase content investigation was carried out with optical and scanning electronic metallography on optical and electronic microscope respectively. Results. A study was conducted on the complex modification of the ЖС3ДК-ВІ alloy with yttrium and particles of ultradispersed titanium carbonitrides Ti(C,N) with variable content (from 0.025 % to 0.075 %), when pouring the melt into a ceramic mould, the first working layer of which was made with cobalt aluminate CoAl2O4 addition. In the structure of samples of experimental variants, along with carbides of spherical morphology, globular carbides were found, in the locations of which, zones enriched in yttrium, molybdenum, and titanium, and depleted in chromium, were observed. The results allow to make an assumption that, probably, high-temperature primary carbides of the YC-type serve as substrates for the formation of low-temperature modifications of MC carbides. In the material, after addition 0.050% ultrafine particles of titanium carbonitrides Ti(C,N) into the yttrium-modified melt, high levels of impact toughness (~70 J/cm2) and rupture life (> 500 h) are provided. Scientific novelty. New data were obtained regarding the phase state of the ЖС3ДК-ВІ alloy after complex modification according to the scheme (Ti(C,N)+Y+CoAl2O4). The fine structure of a nickel-based superalloy, which is traditionally used for large-sized turbine blades production of a gas turbine engine for aviation purposes, has been studied. Practical value. The obtained results expand the possibilities of using heat-resistant ЖС3ДК-ВІ alloy for responsible castings production.