Dmytro Tomkin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dmytro Tomkin has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Valeriy Naumyk
National University Zaporizhzhia Polytechnic
12 shared publications - Oleksii Pedash
MOTOR SICH JSC, Zaporizhzhia, Ukraine
10 shared publications - Olena Naumyk
National University “Zaporizhzhia Polytechnic”, Zaporizhzhia, Ukraine
7 shared publications - S. M. Danilov
Zaporizhzhia Machine-Building Factory, Zaporizhzhia, Ukraine
6 shared publications O. O. Naumyk
National University “Zaporizhzhia Polytechnic”, Ministry of Education and Science of Ukraine, Zaporizhzhia, Ukraine
3 shared publications- Daria V. Tkach
Zaporizhzhia Polytechnic National University
1 shared publication
Latest Publications
- 6 November 2025
- Published by Springer Nature in Materials Science
- Vol. 61 (3) , 316-322
Complex modification of heat-resistant ZhS3DK-VI alloy with yttrium and titanium carbonitride, and niobium
- 6 November 2025
- Published by Springer Nature in Materials Science
- Vol. 61 (3) , 316-322
Complex modification of heat-resistant ZhS3DK-VI alloy with yttrium and titanium carbonitride, and niobium
- 10 June 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 61 (3) , 35-40
Complex modification of heat-resistant ZhS3DK-V1 alloy with itrii and titanium carbonitride and niobium
Samples cast from heat-resistant ZhS3DK-VI nickel alloy modified with yttrium in combination with titanium carbonitride or niobium were studied. It is found that the chemical composition of the samples is satisfactory and meets the requirements of OST 1.90.126-85. Heat resistance, strength and ductility characteristics of the studied samples after hot isostatic pressing and standard heat treatment meet the regulatory requirements. The impact toughness value for the alloy with niobium content is slightly lower than the developer requirements, but is within the regulatory standards. In the microstructure of the alloy with titanium carbonitride, the grain boundaries are mainly thin with the presence of carbides with a size not exceeding 4mμ, as well as carbonitrides in the form of globular clusters near the grain boundaries. As for the alloy with niobium, the grain boundaries are coarser due to the release of carbonitrides up to 7mμ in size, as well as plate-like carbides up to 10mμ long. Thus, complex modification with yttrium and titanium carbonitride ensures the formation of a more favorable structure and significantly improves mechanical and heat-resistant properties of the ZhS3DK-VI nickel alloy.
- 10 June 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 61 (3) , 35-40
Complex modification of heat-resistant ZhS3DK-V1 alloy with itrii and titanium carbonitride and niobium
Samples cast from heat-resistant ZhS3DK-VI nickel alloy modified with yttrium in combination with titanium carbonitride or niobium were studied. It is found that the chemical composition of the samples is satisfactory and meets the requirements of OST 1.90.126-85. Heat resistance, strength and ductility characteristics of the studied samples after hot isostatic pressing and standard heat treatment meet the regulatory requirements. The impact toughness value for the alloy with niobium content is slightly lower than the developer requirements, but is within the regulatory standards. In the microstructure of the alloy with titanium carbonitride, the grain boundaries are mainly thin with the presence of carbides with a size not exceeding 4mμ, as well as carbonitrides in the form of globular clusters near the grain boundaries. As for the alloy with niobium, the grain boundaries are coarser due to the release of carbonitrides up to 7mμ in size, as well as plate-like carbides up to 10mμ long. Thus, complex modification with yttrium and titanium carbonitride ensures the formation of a more favorable structure and significantly improves mechanical and heat-resistant properties of the ZhS3DK-VI nickel alloy.
- Open Access
- 25 March 2025
- Published by National University "Zaporizhzhia Polytechnic" in New Materials and Technologies in Metallurgy and Mechanical Engineering
- No. 1,p. 6-12
ANALYSIS OF THE MODIFICATION EFFECT WITH YTTRIMIUM, HAFNIUM AND NIOBIUM ON ЖС3ДК-ВІ ALLOY WITH REDUCED CARBON CONTENT
Purpose. Theoretical prediction of carbide formation and possibilities of compensating for the lack of carbide strengthening in the ЖС3ДК-ВІ alloy with a reduced carbon content through additional modification with yttrium, hafnium, and niobium. Research methods. By analyzing the corresponding stoichiometric reaction equations, the minimum conditions for obtaining yttrium and hafnium carbides were determined. Using known computational and analytical techniques, the predicted 100- and 1000- hour long-term strength of the ЖС3ДК-ВІ alloy at different alloying levels without modification and a conditional complexly modified with yttrium, hafnium and niobium variant were determined. Scientific novelty. Previous studies have established that in the structure of samples with a reduced carbon content (0.015...0.020 % C) carbides are practically absent, and the grain boundaries are very thin. When niobium, yttrium and hafnium are introduced, carbides are formed in the form of globular particles, mainly evenly distributed in the volume of the metal. Calculations have established that 0.02014 % carbon is sufficient for the carbide formation reaction of 0.015% yttrium and 0.25 % hafnium. As was previously established, when 0.15...0.25 % hafnium is introduced into the ЖС3ДК-ВІ alloy, all carbides are isolated in the form of globular particles, and are located along the grain boundaries and interdendritic spaces. Thus, since it is known that yttrium carbides are released from the melt and are a substrate for the growth of carbides of the MС type in the form of globular particles, we can conclude that the amount of yttrium and hafnium obtained by calculations may be sufficient for the formation of rounded carbides in the metal ЖС3ДК-ВІ with a carbon content of 0.06…0.11% (according to OST 1.90.126-85). Thus, it can be concluded that with a low carbon content: - yttrium does not participate in carbide reactions, but is spent on local alloying of the phase interface, which slows down diffusion processes, increases the structural stability and heat resistance of the alloy, reduces grain size, and refines the dendritic structure; - hafnium prevents the destruction of grain boundaries by suppressing the release of secondary carbides, and strengthens the γ´- phase. To compensate for the lack of carbide strengthening of the alloy with a carbon content of 0.015…0.020 %, the possibilities of strengthening the γ´- phase by alloying the alloy with hafnium and niobium were studied using computational and analytical methods. Practical value. The calculated increase in the long-term strength of a conventional alloy complexly modified with hafnium, niobium and yttrium up to ~12 % relative to the serial alloy ЖС3ДК-ВІ according to OST 1.90.126-85 has been established. Based on the data obtained, it can be concluded that the addition of hafnium in an amount of 0.25% and niobium – 0.50 % compensates for the lack of carbide strengthening of the ЖС3ДК-ВІ alloy at reduced carbon contents.
- 25 March 2025
- Published by National University "Zaporizhzhia Polytechnic" in New Materials and Technologies in Metallurgy and Mechanical Engineering
- No. 1,p. 6-12
Open AccessANALYSIS OF THE MODIFICATION EFFECT WITH YTTRIMIUM, HAFNIUM AND NIOBIUM ON ЖС3ДК-ВІ ALLOY WITH REDUCED CARBON CONTENT
Purpose. Theoretical prediction of carbide formation and possibilities of compensating for the lack of carbide strengthening in the ЖС3ДК-ВІ alloy with a reduced carbon content through additional modification with yttrium, hafnium, and niobium. Research methods. By analyzing the corresponding stoichiometric reaction equations, the minimum conditions for obtaining yttrium and hafnium carbides were determined. Using known computational and analytical techniques, the predicted 100- and 1000- hour long-term strength of the ЖС3ДК-ВІ alloy at different alloying levels without modification and a conditional complexly modified with yttrium, hafnium and niobium variant were determined. Scientific novelty. Previous studies have established that in the structure of samples with a reduced carbon content (0.015...0.020 % C) carbides are practically absent, and the grain boundaries are very thin. When niobium, yttrium and hafnium are introduced, carbides are formed in the form of globular particles, mainly evenly distributed in the volume of the metal. Calculations have established that 0.02014 % carbon is sufficient for the carbide formation reaction of 0.015% yttrium and 0.25 % hafnium. As was previously established, when 0.15...0.25 % hafnium is introduced into the ЖС3ДК-ВІ alloy, all carbides are isolated in the form of globular particles, and are located along the grain boundaries and interdendritic spaces. Thus, since it is known that yttrium carbides are released from the melt and are a substrate for the growth of carbides of the MС type in the form of globular particles, we can conclude that the amount of yttrium and hafnium obtained by calculations may be sufficient for the formation of rounded carbides in the metal ЖС3ДК-ВІ with a carbon content of 0.06…0.11% (according to OST 1.90.126-85). Thus, it can be concluded that with a low carbon content: - yttrium does not participate in carbide reactions, but is spent on local alloying of the phase interface, which slows down diffusion processes, increases the structural stability and heat resistance of the alloy, reduces grain size, and refines the dendritic structure; - hafnium prevents the destruction of grain boundaries by suppressing the release of secondary carbides, and strengthens the γ´- phase. To compensate for the lack of carbide strengthening of the alloy with a carbon content of 0.015…0.020 %, the possibilities of strengthening the γ´- phase by alloying the alloy with hafnium and niobium were studied using computational and analytical methods. Practical value. The calculated increase in the long-term strength of a conventional alloy complexly modified with hafnium, niobium and yttrium up to ~12 % relative to the serial alloy ЖС3ДК-ВІ according to OST 1.90.126-85 has been established. Based on the data obtained, it can be concluded that the addition of hafnium in an amount of 0.25% and niobium – 0.50 % compensates for the lack of carbide strengthening of the ЖС3ДК-ВІ alloy at reduced carbon contents.
- Open Access
- 5 March 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 159 (1) , 3-10
INFLUENCE OF REDUCED CARBON CONTENT ON THE PROPERTIES OF ZHS3DK-VI ALLOY
The effect of reduced carbon content (0.015...0.020 % С) and, accordingly, the carbide phase on the properties of ЖС3ДК-ВІ alloy with additional alloying and modification with niobium, hafnium-nickel and nickel-yttrium alloys was investigated. It was established that in the structure of test samples with reduced carbon content, carbides are practically absent, and grain boundaries are very thin. When niobium, yttrium and hafnium are introduced, carbides are formed in the form of globular particles mostly uniformly distributed in the volume of the metal. The microstructure of samples with reduced carbon content is coarsely crystalline, which is probably due to the absence of competitive phase growth during melt crystallization. Experimental variants with low carbon content have impact toughness values at the level of 90...150 J/cm2, but extremely low long-term strength, probably due to the lack of carbide strengthening in the alloy. High impact toughness values are associated with the uniform distribution of the finely dispersed carbonitride phase in the structure. Complex modified (Nb+Hf+Y) samples, with a carbon content of 0.06%, showed sufficient impact toughness and long-term strength, which significantly exceeded the requirements of OST 1.90126-85. In these samples, the almost complete absence of large carbides in the bulk of the main γ-solid solution grains and the presence of small carbides of the Me23C6 type, which were released during heat treatment along the grain boundaries, prevented grain boundary slippage under conditions of high temperatures and applied load. The level of impact toughness, in this case, is provided by the release and uniform distribution of discrete and globular carbides and carbonitrides (approximately 2...3 µm in size) during the treatment of the melt with yttrium and hafnium. The decrease in impact strength, compared to low-carbon options, is probably due to the release of double carbides of font morphology. Досліджено вплив зниженого вмісту вуглецю (0,015…0,020 % С) та, відповідно, карбідної фази на властивості сплаву ЖС3ДК-ВІ з додатковим легуванням та модифікуванням ніобієм, лігатурами гафній-нікель та нікель-ітрій. Встановлено, що у структурі дослідних зразків зі зниженим вмістом вуглецю карбіди практично відсутні, а межі зерен дуже тонкі. При введенні ніобію, ітрію та гафнію відбувається утворення карбідів у формі глобулярних частинок, в основному рівномірно розподілених в об’ємі металу. Мікроструктура зразків зі зниженим вмістом вуглецю крупно кристалічна, що, ймовірно, зумовлено відсутністю конкурентного фазового росту при кристалізації розплаву. Дослідні варіанти з низьким вмістом вуглецю мають значення ударної в’язкості на рівні 90…150 Дж/см2, але вкрай низьку тривалу міцність, мабуть, через відсутність карбідного зміцнення у сплаві. Високі показники ударної в’язкості пов’язані з рівномірним розподілом у структурі дрібнодисперсної карбонітридної фази. Комплексно модифіковані (Nb+Hf+Y) зразки із вмістом вуглецю 0,06 %, показали достатню ударну в’язкість і тривалу міцність, що значно перевищувало вимоги ОСТ 1.90126-85. У цих зразках практично повністю відсутні великі карбіди в об’ємі зерен основного γ-твердого розчину і наявні дрібні карбіди типу Ме23С6, що виділилися в процесі термічної обробки по межах зерен, перешкоджали зернограничному прослизанню в умовах високих температур і прикладеного навантаження. Рівень ударної в’язкості в даному випадку забезпечується виділенням і рівномірним розподілом дискретних і глобулярних карбідів та карбонітридів (розміром приблизно 2...3 мкм) при обробці розплаву ітрієм і гафнієм. Зниження ударної в’язкості, порівняно з варіантами з низьким вмістом вуглецю, ймовірно, пов’язане з виділенням подвійних карбідів шрифтової морфології.
- 5 March 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 159 (1) , 3-10
Open AccessINFLUENCE OF REDUCED CARBON CONTENT ON THE PROPERTIES OF ZHS3DK-VI ALLOY
The effect of reduced carbon content (0.015...0.020 % С) and, accordingly, the carbide phase on the properties of ЖС3ДК-ВІ alloy with additional alloying and modification with niobium, hafnium-nickel and nickel-yttrium alloys was investigated. It was established that in the structure of test samples with reduced carbon content, carbides are practically absent, and grain boundaries are very thin. When niobium, yttrium and hafnium are introduced, carbides are formed in the form of globular particles mostly uniformly distributed in the volume of the metal. The microstructure of samples with reduced carbon content is coarsely crystalline, which is probably due to the absence of competitive phase growth during melt crystallization. Experimental variants with low carbon content have impact toughness values at the level of 90...150 J/cm2, but extremely low long-term strength, probably due to the lack of carbide strengthening in the alloy. High impact toughness values are associated with the uniform distribution of the finely dispersed carbonitride phase in the structure. Complex modified (Nb+Hf+Y) samples, with a carbon content of 0.06%, showed sufficient impact toughness and long-term strength, which significantly exceeded the requirements of OST 1.90126-85. In these samples, the almost complete absence of large carbides in the bulk of the main γ-solid solution grains and the presence of small carbides of the Me23C6 type, which were released during heat treatment along the grain boundaries, prevented grain boundary slippage under conditions of high temperatures and applied load. The level of impact toughness, in this case, is provided by the release and uniform distribution of discrete and globular carbides and carbonitrides (approximately 2...3 µm in size) during the treatment of the melt with yttrium and hafnium. The decrease in impact strength, compared to low-carbon options, is probably due to the release of double carbides of font morphology. Досліджено вплив зниженого вмісту вуглецю (0,015…0,020 % С) та, відповідно, карбідної фази на властивості сплаву ЖС3ДК-ВІ з додатковим легуванням та модифікуванням ніобієм, лігатурами гафній-нікель та нікель-ітрій. Встановлено, що у структурі дослідних зразків зі зниженим вмістом вуглецю карбіди практично відсутні, а межі зерен дуже тонкі. При введенні ніобію, ітрію та гафнію відбувається утворення карбідів у формі глобулярних частинок, в основному рівномірно розподілених в об’ємі металу. Мікроструктура зразків зі зниженим вмістом вуглецю крупно кристалічна, що, ймовірно, зумовлено відсутністю конкурентного фазового росту при кристалізації розплаву. Дослідні варіанти з низьким вмістом вуглецю мають значення ударної в’язкості на рівні 90…150 Дж/см2, але вкрай низьку тривалу міцність, мабуть, через відсутність карбідного зміцнення у сплаві. Високі показники ударної в’язкості пов’язані з рівномірним розподілом у структурі дрібнодисперсної карбонітридної фази. Комплексно модифіковані (Nb+Hf+Y) зразки із вмістом вуглецю 0,06 %, показали достатню ударну в’язкість і тривалу міцність, що значно перевищувало вимоги ОСТ 1.90126-85. У цих зразках практично повністю відсутні великі карбіди в об’ємі зерен основного γ-твердого розчину і наявні дрібні карбіди типу Ме23С6, що виділилися в процесі термічної обробки по межах зерен, перешкоджали зернограничному прослизанню в умовах високих температур і прикладеного навантаження. Рівень ударної в’язкості в даному випадку забезпечується виділенням і рівномірним розподілом дискретних і глобулярних карбідів та карбонітридів (розміром приблизно 2...3 мкм) при обробці розплаву ітрієм і гафнієм. Зниження ударної в’язкості, порівняно з варіантами з низьким вмістом вуглецю, ймовірно, пов’язане з виділенням подвійних карбідів шрифтової морфології.
- 14 February 2025
- Published by Springer Nature
- p. 468-477
Investigation of Zhs3dk-VI Alloy as a Material of Gas Turbine Engine Cast Blades
- 14 February 2025
- Published by Springer Nature
- p. 468-477
Investigation of Zhs3dk-VI Alloy as a Material of Gas Turbine Engine Cast Blades
- Open Access
- 29 January 2025
- Published by National University "Zaporizhzhia Polytechnic" in New Materials and Technologies in Metallurgy and Mechanical Engineering
- No. 4,p. 6-14
COMPLEX MODIFICATION OF NICKEL-BASED SUPERALLOY WITH ULTRA-FINE REFRACTORY COMPOUNDS PARTICLE
Purpose. Due to the complex modification of nickel-based superalloy with modifiers of different mechanisms of action, it is possible to increase the characteristics of plasticity and impact strength to a level that will allow to localize the possible destruction of large-sized blades of a low-pressure turbine of an aircraft engine during operation cycle. Research methods. Microstructure analysis and phase content investigation was carried out with optical and scanning electronic metallography on optical and electronic microscope respectively. Results. A study was conducted on the complex modification of the ЖС3ДК-ВІ alloy with yttrium and particles of ultradispersed titanium carbonitrides Ti(C,N) with variable content (from 0.025 % to 0.075 %), when pouring the melt into a ceramic mould, the first working layer of which was made with cobalt aluminate CoAl2O4 addition. In the structure of samples of experimental variants, along with carbides of spherical morphology, globular carbides were found, in the locations of which, zones enriched in yttrium, molybdenum, and titanium, and depleted in chromium, were observed. The results allow to make an assumption that, probably, high-temperature primary carbides of the YC-type serve as substrates for the formation of low-temperature modifications of MC carbides. In the material, after addition 0.050% ultrafine particles of titanium carbonitrides Ti(C,N) into the yttrium-modified melt, high levels of impact toughness (~70 J/cm2) and rupture life (> 500 h) are provided. Scientific novelty. New data were obtained regarding the phase state of the ЖС3ДК-ВІ alloy after complex modification according to the scheme (Ti(C,N)+Y+CoAl2O4). The fine structure of a nickel-based superalloy, which is traditionally used for large-sized turbine blades production of a gas turbine engine for aviation purposes, has been studied. Practical value. The obtained results expand the possibilities of using heat-resistant ЖС3ДК-ВІ alloy for responsible castings production.
- 29 January 2025
- Published by National University "Zaporizhzhia Polytechnic" in New Materials and Technologies in Metallurgy and Mechanical Engineering
- No. 4,p. 6-14
Open AccessCOMPLEX MODIFICATION OF NICKEL-BASED SUPERALLOY WITH ULTRA-FINE REFRACTORY COMPOUNDS PARTICLE
Purpose. Due to the complex modification of nickel-based superalloy with modifiers of different mechanisms of action, it is possible to increase the characteristics of plasticity and impact strength to a level that will allow to localize the possible destruction of large-sized blades of a low-pressure turbine of an aircraft engine during operation cycle. Research methods. Microstructure analysis and phase content investigation was carried out with optical and scanning electronic metallography on optical and electronic microscope respectively. Results. A study was conducted on the complex modification of the ЖС3ДК-ВІ alloy with yttrium and particles of ultradispersed titanium carbonitrides Ti(C,N) with variable content (from 0.025 % to 0.075 %), when pouring the melt into a ceramic mould, the first working layer of which was made with cobalt aluminate CoAl2O4 addition. In the structure of samples of experimental variants, along with carbides of spherical morphology, globular carbides were found, in the locations of which, zones enriched in yttrium, molybdenum, and titanium, and depleted in chromium, were observed. The results allow to make an assumption that, probably, high-temperature primary carbides of the YC-type serve as substrates for the formation of low-temperature modifications of MC carbides. In the material, after addition 0.050% ultrafine particles of titanium carbonitrides Ti(C,N) into the yttrium-modified melt, high levels of impact toughness (~70 J/cm2) and rupture life (> 500 h) are provided. Scientific novelty. New data were obtained regarding the phase state of the ЖС3ДК-ВІ alloy after complex modification according to the scheme (Ti(C,N)+Y+CoAl2O4). The fine structure of a nickel-based superalloy, which is traditionally used for large-sized turbine blades production of a gas turbine engine for aviation purposes, has been studied. Practical value. The obtained results expand the possibilities of using heat-resistant ЖС3ДК-ВІ alloy for responsible castings production.
- 1 November 2024
- Published by Springer Nature in Materials Science
- Vol. 60 (3) , 389-396
Complex modification of heat-resistant ZhS3DK-VI alloy with yttrium and titanium carbonitride
- 1 November 2024
- Published by Springer Nature in Materials Science
- Vol. 60 (3) , 389-396
Complex modification of heat-resistant ZhS3DK-VI alloy with yttrium and titanium carbonitride
- 24 June 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 60 (3) , 137-143
Complex modification of heat-resistant ZhS3DK-VІ alloy with yttrium and titanium carbonitride
Samples cast from heat-resistant nickel ZhS3DK-VІ alloy, complex modified with yttrium and titanium carbonitride in various combinations, after hot isostatic pressing (HIP) and subsequent heat treatment, were investigated. For comparison, complex modification was performed with the simultaneous use of yttrium and cerium. It was established that the chemical composition (taking into account the presence of yttrium in the alloys), as well as the mechanical and heat-resistant properties of the cast samples meet the requirements of OST 1.90.126-85, with the exception of the impact ductility of the samples without titanium carbonitride, which is almost twice lower than the additional requirements put forward by the developer for responsible aircraft castings, and also for the samples with titanium carbonitride. The best modifying effect was obtained with the complex modified alloy with 0.075% titanium carbonitride. In other options, there is a coarsening of the structure, and for the samples without titanium carbonitride, melting of the eutectic (γ-γ)′-phase is also observed, which probably contributs to the reduction of impact toughness. As a result of HIP, micropores and loosening which do not reach the surface of the parts (located in the internal volumes of the metal) are healed, which contributes to the stabilization of the material structure and properties.
- 24 June 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 60 (3) , 137-143
Complex modification of heat-resistant ZhS3DK-VІ alloy with yttrium and titanium carbonitride
Samples cast from heat-resistant nickel ZhS3DK-VІ alloy, complex modified with yttrium and titanium carbonitride in various combinations, after hot isostatic pressing (HIP) and subsequent heat treatment, were investigated. For comparison, complex modification was performed with the simultaneous use of yttrium and cerium. It was established that the chemical composition (taking into account the presence of yttrium in the alloys), as well as the mechanical and heat-resistant properties of the cast samples meet the requirements of OST 1.90.126-85, with the exception of the impact ductility of the samples without titanium carbonitride, which is almost twice lower than the additional requirements put forward by the developer for responsible aircraft castings, and also for the samples with titanium carbonitride. The best modifying effect was obtained with the complex modified alloy with 0.075% titanium carbonitride. In other options, there is a coarsening of the structure, and for the samples without titanium carbonitride, melting of the eutectic (γ-γ)′-phase is also observed, which probably contributs to the reduction of impact toughness. As a result of HIP, micropores and loosening which do not reach the surface of the parts (located in the internal volumes of the metal) are healed, which contributes to the stabilization of the material structure and properties.
- Open Access
- 25 February 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 155 (1) , 39-47
INFLUENCE OF CONDITIONAL RETURN CHEMICAL COMPOSITION AND MODIFICATION BALANCE ON THE PROPERTIES OF ZHS6U-VI ALLOY
The influence of the Сr+W+Mo, Ti+Al values and yttrium modification of the condition return on the mechanical properties and long-term strength of the ЖС6У-ВІ alloy was studied. It was established that the method of ЖС6У-ВІ alloy melt refining affects the separation of phases along the grain boundaries and allows an increase in the content of the γ’-phase, as a result of which it is possible to consider the admissibility of increasing the value of the Ti + Al sum, probably up to 8.3%. Refreshing the condition return during remelting allows you to control the chemical composition of the metal. To optimize the refreshing of the alloy, remelting must be carried out in an installation equipped with a sampling module to determine the chemical composition of the alloy during melting. Modification of the nickel-yttrium alloy with estimated 0.01% yttrium content in the metal makes it possible to ensure the absence of phase separation along the grain boundaries, reduces the grain size of the macrostructure. The modification increases the mechanical properties at room temperature, but reduces the long-term strength of the ЖС6У-ВІ alloy at high temperatures, which is a consequence of the reduction of the macrograin size. Досліджено вплив значення сум Сr+W+Mo, Ti+Al та модифікування ітрієм кондиційного во- роття на механічні властивості й тривалу міцність сплаву ЖС6У-ВІ. Встановлено, що спосіб рафінування розплаву сплаву ЖС6У-ВІ впливає на виділення фаз по межах зерен і допускає підвищення вмісту γ’-фази, внаслідок чого можна розглядати припустимість збільшення значення суми Ti+Al, ймовірно до 8,3 %. Освіження кондиційного вороття металу під час про- ведення переплаву дозволяє керувати хімічним складом металу. Для оптимізації освіження вороття сплаву, переплав необхідно проводити в установці, що обладнана модулем відбору проб для визначення хімічного складу сплаву під час ведення плавки. Модифікування сплаву нікель-ітрієвою лігатурою на розрахунковий вміст 0,01 % ітрію в металі дозволяє забез- печити відсутність виділень фаз по межах зерен, зменшує розмір зерен макроструктури. Модифікування підвищує механічні властивості при кімнатній температурі, але знижує тривалу міцність сплаву ЖС6У-ВІ при підвищених температурах, що є наслідком зменшення розміру макрозерна.
- 25 February 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 155 (1) , 39-47
Open AccessINFLUENCE OF CONDITIONAL RETURN CHEMICAL COMPOSITION AND MODIFICATION BALANCE ON THE PROPERTIES OF ZHS6U-VI ALLOY
The influence of the Сr+W+Mo, Ti+Al values and yttrium modification of the condition return on the mechanical properties and long-term strength of the ЖС6У-ВІ alloy was studied. It was established that the method of ЖС6У-ВІ alloy melt refining affects the separation of phases along the grain boundaries and allows an increase in the content of the γ’-phase, as a result of which it is possible to consider the admissibility of increasing the value of the Ti + Al sum, probably up to 8.3%. Refreshing the condition return during remelting allows you to control the chemical composition of the metal. To optimize the refreshing of the alloy, remelting must be carried out in an installation equipped with a sampling module to determine the chemical composition of the alloy during melting. Modification of the nickel-yttrium alloy with estimated 0.01% yttrium content in the metal makes it possible to ensure the absence of phase separation along the grain boundaries, reduces the grain size of the macrostructure. The modification increases the mechanical properties at room temperature, but reduces the long-term strength of the ЖС6У-ВІ alloy at high temperatures, which is a consequence of the reduction of the macrograin size. Досліджено вплив значення сум Сr+W+Mo, Ti+Al та модифікування ітрієм кондиційного во- роття на механічні властивості й тривалу міцність сплаву ЖС6У-ВІ. Встановлено, що спосіб рафінування розплаву сплаву ЖС6У-ВІ впливає на виділення фаз по межах зерен і допускає підвищення вмісту γ’-фази, внаслідок чого можна розглядати припустимість збільшення значення суми Ti+Al, ймовірно до 8,3 %. Освіження кондиційного вороття металу під час про- ведення переплаву дозволяє керувати хімічним складом металу. Для оптимізації освіження вороття сплаву, переплав необхідно проводити в установці, що обладнана модулем відбору проб для визначення хімічного складу сплаву під час ведення плавки. Модифікування сплаву нікель-ітрієвою лігатурою на розрахунковий вміст 0,01 % ітрію в металі дозволяє забез- печити відсутність виділень фаз по межах зерен, зменшує розмір зерен макроструктури. Модифікування підвищує механічні властивості при кімнатній температурі, але знижує тривалу міцність сплаву ЖС6У-ВІ при підвищених температурах, що є наслідком зменшення розміру макрозерна.