Dalton Cox
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dalton Cox has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Scott Alexander Barnett
Northwestern University
7 shared publications - Beom-Kyeong Park
School of Materials Science and Engineering, Pusan National University, Busan 46241, Republic of Korea
3 shared publications - Jakob Michael Reinke
Northwestern University
2 shared publications - Roberto Scipioni
Department of Thermal Energy, SINTEF Energy Research, Trondheim, Norway
2 shared publications - Travis Anthony Schmauss
Northwestern University
2 shared publications - Yubo Zhang
Northwestern University
2 shared publications
Latest Publications
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (41) , 2066
(Invited) Ni Migration in Ni-YSZ Electrodes during Solid Oxide Electrolysis Cell Operation
Nickel-yttria stabilized zirconia (Ni-YSZ) is the state-of-the-art fuel electrode in solid oxide cells, but microstructural changes often occur during operation that can cause performance degradation. This talk will focus on the Ni migration near the electrode/electrolyte interface of solid oxide electrolysis cells (SOECs). The factors believed to cause Ni migration are discussed. The effect is often attributed to a spatial gradient in Ni wetting angle in the electrode active region. One possible mechanism, electrowetting at Ni/YSZ interfaces, is explored as a possible cause of the wettability gradient. Surface diffusion and vapor transport are possible transport mechanisms, but the latter is found to be slow at normal operating temperatures < 850 oC.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (41) , 2066
(Invited) Ni Migration in Ni-YSZ Electrodes during Solid Oxide Electrolysis Cell Operation
Nickel-yttria stabilized zirconia (Ni-YSZ) is the state-of-the-art fuel electrode in solid oxide cells, but microstructural changes often occur during operation that can cause performance degradation. This talk will focus on the Ni migration near the electrode/electrolyte interface of solid oxide electrolysis cells (SOECs). The factors believed to cause Ni migration are discussed. The effect is often attributed to a spatial gradient in Ni wetting angle in the electrode active region. One possible mechanism, electrowetting at Ni/YSZ interfaces, is explored as a possible cause of the wettability gradient. Surface diffusion and vapor transport are possible transport mechanisms, but the latter is found to be slow at normal operating temperatures < 850 oC.
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (54) , 79
Phase Stability of SrTi1-XFexO3- δ Under Solid Oxide Cell Fuel-Electrode Conditions: Implications for Related Exsolution Electrode Materials
Perovskite oxides with catalytically active metal nanoparticle exsolution are receiving considerable attention as alternative Solid Oxide Cell fuel-electrode materials. For exsolution, a small amount of a cation is substituted on the B-site of the base oxide and then is reduced out of the host lattice to form nanoparticles that promote electrochemical processes. During exsolution, the host lattice generally becomes more B-site deficient. In some cases, the oxide is made initially A-site deficient to compensate for the loss of B-site cations. Thus, the stability of these oxides under a range of stoichiometries and fuel electrode conditions is of interest. Here we focus on one perovskite host material of interest, SrTi1-xFexO3- δ (STF), which has shown good fuel electrode characteristics that can be enhanced by the substitution of Ru or Ni, resulting in exsolution to form Ru-Fe or Ni-Fe alloy nanoparticles, respectively. (1, 2) Although the amounts of Ru or Ni substituted are small, typically ~ 7% of the B-site cations, the co-exsolution of a comparable amount of Fe is usually observed, resulting in substantial B-site deficiency, potentially de-stabilizing the host perovskite phase. The stability of Fe in STF is also of interest because it helps to determine the Fe content of the alloy nanoparticles. (3) This study seeks to determine the stability of STF in various reducing fuel environments. While STF has been mostly studied as SrTi0.3Fe0.7O3-δ (STF-7), it is not known if this composition provides the best combination of stability and electrochemical performance. Thus, a few additional compositions, SrTi0.5Fe0.5O3- δ (STF-5), SrTi0.4Fe0.6O3- δ (STF-6), and SrTi0.2Fe0.8O3- δ (STF-8), have been studied. In general, the Fe-rich compositions are expected to possess higher electronic and ionic conductivity, leading to good electrochemical performance, whereas the more Ti-rich compositions are expected to provide better stability. Exposure to 97% H2 – 3% H2O at 850°C for 4 h resulted in STF decomposition into BCC α-Fe and a Ruddlesden-Popper (RP) phase, but the decomposition became more limited for the more Ti-rich compositions (Figure 1a). The main Fe peak overlaps with one of the RP peaks, but the presence of α-Fe particles is clearly visible in STEM energy dispersive x-ray spectroscopy chemical mapping, shown for STF-7 in Figure 1b. Figure 1c shows that there is a critical p(O2), 1.3 x 10-20 atm, below which decomposition of perovskite STF-7 occurs. In addition to ex situ XRD as shown in Figure 1, in situ XRD results will be presented and used to confirm and quantify phase changes in combination with thermogravimetric analysis (TGA). Additionally, the conductivity and electrochemical performance of the various STF compositions will be reported and discussed relative to the phase change from perovskite to Ruddlesden Popper and the Fe exsolution. The other main materials variable to be explored is the A-to-B site stoichiometry, which will be studied over the range expected during exsolution. The implications of these results for various exsolution electrode compositions will be discussed. Figure 1: a) Reductions of STF-5 through STF-8 all yield significant decomposition as the initially pristine perovskite acquires several additional peaks. b) Using energy dispersive x-ray spectroscopy, it can be shown that significant Fe deposits appear in STF-7 after reduction at 850°C (effective pO2 1.2e-21 atm for 4 hours). c By increasing pO2 by a factor of 10, XRD patterns for STF-7 show no clear Ruddlesden-Popper or α-Fe peaks, indicating that decomposition requires significantly reducing conditions and that STF may remain stable under more oxidizing conditions. References R. Glaser, T. Zhu, H. Troiani, A. Caneiro, L. Mogni and S. Barnett, Journal of Materials Chemistry A, 6, 5193 (2018). T. Zhu, H. Troiani, L. V. Mogni, M. Santaya, M. Han and S. A. Barnett, Journal of Power Sources, 439 (2019). T. Zhu, H. E. Troiani, L. V. Mogni, M. Han and S. A. Barnett, Joule, 2, 478 (2018). Figure 1
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (54) , 79
Phase Stability of SrTi1-XFexO3- δ Under Solid Oxide Cell Fuel-Electrode Conditions: Implications for Related Exsolution Electrode Materials
Perovskite oxides with catalytically active metal nanoparticle exsolution are receiving considerable attention as alternative Solid Oxide Cell fuel-electrode materials. For exsolution, a small amount of a cation is substituted on the B-site of the base oxide and then is reduced out of the host lattice to form nanoparticles that promote electrochemical processes. During exsolution, the host lattice generally becomes more B-site deficient. In some cases, the oxide is made initially A-site deficient to compensate for the loss of B-site cations. Thus, the stability of these oxides under a range of stoichiometries and fuel electrode conditions is of interest. Here we focus on one perovskite host material of interest, SrTi1-xFexO3- δ (STF), which has shown good fuel electrode characteristics that can be enhanced by the substitution of Ru or Ni, resulting in exsolution to form Ru-Fe or Ni-Fe alloy nanoparticles, respectively. (1, 2) Although the amounts of Ru or Ni substituted are small, typically ~ 7% of the B-site cations, the co-exsolution of a comparable amount of Fe is usually observed, resulting in substantial B-site deficiency, potentially de-stabilizing the host perovskite phase. The stability of Fe in STF is also of interest because it helps to determine the Fe content of the alloy nanoparticles. (3) This study seeks to determine the stability of STF in various reducing fuel environments. While STF has been mostly studied as SrTi0.3Fe0.7O3-δ (STF-7), it is not known if this composition provides the best combination of stability and electrochemical performance. Thus, a few additional compositions, SrTi0.5Fe0.5O3- δ (STF-5), SrTi0.4Fe0.6O3- δ (STF-6), and SrTi0.2Fe0.8O3- δ (STF-8), have been studied. In general, the Fe-rich compositions are expected to possess higher electronic and ionic conductivity, leading to good electrochemical performance, whereas the more Ti-rich compositions are expected to provide better stability. Exposure to 97% H2 – 3% H2O at 850°C for 4 h resulted in STF decomposition into BCC α-Fe and a Ruddlesden-Popper (RP) phase, but the decomposition became more limited for the more Ti-rich compositions (Figure 1a). The main Fe peak overlaps with one of the RP peaks, but the presence of α-Fe particles is clearly visible in STEM energy dispersive x-ray spectroscopy chemical mapping, shown for STF-7 in Figure 1b. Figure 1c shows that there is a critical p(O2), 1.3 x 10-20 atm, below which decomposition of perovskite STF-7 occurs. In addition to ex situ XRD as shown in Figure 1, in situ XRD results will be presented and used to confirm and quantify phase changes in combination with thermogravimetric analysis (TGA). Additionally, the conductivity and electrochemical performance of the various STF compositions will be reported and discussed relative to the phase change from perovskite to Ruddlesden Popper and the Fe exsolution. The other main materials variable to be explored is the A-to-B site stoichiometry, which will be studied over the range expected during exsolution. The implications of these results for various exsolution electrode compositions will be discussed. Figure 1: a) Reductions of STF-5 through STF-8 all yield significant decomposition as the initially pristine perovskite acquires several additional peaks. b) Using energy dispersive x-ray spectroscopy, it can be shown that significant Fe deposits appear in STF-7 after reduction at 850°C (effective pO2 1.2e-21 atm for 4 hours). c By increasing pO2 by a factor of 10, XRD patterns for STF-7 show no clear Ruddlesden-Popper or α-Fe peaks, indicating that decomposition requires significantly reducing conditions and that STF may remain stable under more oxidizing conditions. References R. Glaser, T. Zhu, H. Troiani, A. Caneiro, L. Mogni and S. Barnett, Journal of Materials Chemistry A, 6, 5193 (2018). T. Zhu, H. Troiani, L. V. Mogni, M. Santaya, M. Han and S. A. Barnett, Journal of Power Sources, 439 (2019). T. Zhu, H. E. Troiani, L. V. Mogni, M. Han and S. A. Barnett, Joule, 2, 478 (2018). Figure 1
- 19 May 2023
- Published by The Electrochemical Society in ECS Transactions
- Vol. 111 (6) , 475-483
Phase Stability of SrTi1-XFexO3- δ Under Solid Oxide Cell Fuel-Electrode Conditions: Implications for Related Exsolution Electrode Materials
SrTi1-xFexO3-δ (STF) has shown promise as a fuel electrode, and as a basis for fuel electrodes with catalytically active nanoparticle exsolution. This study aims to determine trends in performance and stability of STF in highly reducing environments as Fe-content is varied from x = 0.5 to 0.8. Here we report that, while polarization resistance of STF fuel electrodes decreases with higher Fe-content, this is accompanied with lower stability in highly reducing conditions. For too-reducing conditions and too-high x, partial decomposition of the original perovskite phase is observed with the formation of metallic Fe and a Ruddlesden-Popper STF phase.
- 19 May 2023
- Published by The Electrochemical Society in ECS Transactions
- Vol. 111 (6) , 475-483
Phase Stability of SrTi1-XFexO3- δ Under Solid Oxide Cell Fuel-Electrode Conditions: Implications for Related Exsolution Electrode Materials
SrTi1-xFexO3-δ (STF) has shown promise as a fuel electrode, and as a basis for fuel electrodes with catalytically active nanoparticle exsolution. This study aims to determine trends in performance and stability of STF in highly reducing environments as Fe-content is varied from x = 0.5 to 0.8. Here we report that, while polarization resistance of STF fuel electrodes decreases with higher Fe-content, this is accompanied with lower stability in highly reducing conditions. For too-reducing conditions and too-high x, partial decomposition of the original perovskite phase is observed with the formation of metallic Fe and a Ruddlesden-Popper STF phase.
- Open Access
- 1 February 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (2) , 024514
A Method for Time-Resolved Characterization of Polarization-Induced Solid Oxide Cell Microstructure Evolution
Solid oxide cell long-term durability experiments are resource-intensive and have limited ability to capture the interdependence of microstructural evolution and electrochemical performance. Studies of microstructural degradation mechanisms are usually limited to before and after life-test images. Here we describe a life testing method that simultaneously operates multiple symmetric cells under different conditions, simultaneously providing information on electrolysis and fuel cell operation, while sampling the microstructure during operation. The method utilizes laser-cutting to exactly define different cell areas, allowing testing under different current densities with a single current source, and facilitating removal of segments of the cells during life tests, allowing for microstructural evaluation at intermediate times. The method is demonstrated in Ni-YSZ / YSZ / Ni-YSZ fuel-electrode-supported cells at low H2O/H2 ratios. Characterization using SEM-based imaging techniques shows pronounced microstructural damage that increases rapidly with increasing current density and time, mirroring observed electrochemical degradation. The present results agree with prior reports for SOC operation under such conditions but reveal new features of the degradation process via the unique capability of time-resolved imaging.
- 1 February 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (2) , 024514
Open AccessA Method for Time-Resolved Characterization of Polarization-Induced Solid Oxide Cell Microstructure Evolution
Solid oxide cell long-term durability experiments are resource-intensive and have limited ability to capture the interdependence of microstructural evolution and electrochemical performance. Studies of microstructural degradation mechanisms are usually limited to before and after life-test images. Here we describe a life testing method that simultaneously operates multiple symmetric cells under different conditions, simultaneously providing information on electrolysis and fuel cell operation, while sampling the microstructure during operation. The method utilizes laser-cutting to exactly define different cell areas, allowing testing under different current densities with a single current source, and facilitating removal of segments of the cells during life tests, allowing for microstructural evaluation at intermediate times. The method is demonstrated in Ni-YSZ / YSZ / Ni-YSZ fuel-electrode-supported cells at low H2O/H2 ratios. Characterization using SEM-based imaging techniques shows pronounced microstructural damage that increases rapidly with increasing current density and time, mirroring observed electrochemical degradation. The present results agree with prior reports for SOC operation under such conditions but reveal new features of the degradation process via the unique capability of time-resolved imaging.
- 1 June 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 8 (23) , 11687-11694
Tuning electrochemical and transport processes to achieve extreme performance and efficiency in solid oxide cells
A new SOC that utilizes a very thin GDC/YSZ bi-layer electrolyte, support with enhanced porosity, and electrode surface modification via PrOx and GDC nanocatalysts pushes the limits of cell polarizations, exceeding fuel cell power density ∼3 W cm−2 and electrolysis current density ∼4 A cm−2.
- 1 June 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 8 (23) , 11687-11694
Tuning electrochemical and transport processes to achieve extreme performance and efficiency in solid oxide cells
A new SOC that utilizes a very thin GDC/YSZ bi-layer electrolyte, support with enhanced porosity, and electrode surface modification via PrOx and GDC nanocatalysts pushes the limits of cell polarizations, exceeding fuel cell power density ∼3 W cm−2 and electrolysis current density ∼4 A cm−2.
- 1 February 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 8 (7) , 4099-4106
Enhancement of Ni–(Y2O3)0.08(ZrO2)0.92 fuel electrode performance by infiltration of Ce0.8Gd0.2O2−δ nanoparticles
This paper addresses the use of Ce0.8Gd0.2O2−δ (GDC) infiltration into the Ni–(Y2O3)0.08(ZrO2)0.92 (YSZ) fuel electrode of solid oxide cells (SOCs) for improving their electrochemical performance in fuel cell and electrolysis operation. Although doped ceria infiltration into Ni–YSZ has recently been shown to improve the electrode performance and stability, the mechanisms defining how GDC impacts electrochemical characteristics are not fully delineated. Furthermore, the electrochemical characteristics have not yet been determined over the full range of conditions normally encountered in fuel cell and electrolysis operation. Here we present a study of both symmetric and full cells aimed at understanding the electrochemical mechanisms of GDC-modified Ni–YSZ over a wide range of fuel compositions and temperatures. Single-step GDC infiltration at an appropriate loading substantially reduced the polarization resistance of Ni–YSZ electrodes in electrolyte-supported cells, as measured using electrochemical impedance spectroscopy (EIS) at various temperatures (600–800 °C) in a range of H2O–H2 mixtures (3–90 vol% H2O). Fuel-electrode-supported cells had significant concentration polarization due to the thick Ni–YSZ supports. A distribution of relaxation times approach is used to develop a physically-based electrochemical model; the results show that GDC reduces the reaction resistance associated with three-phase boundaries, but also appears to improve oxygen transport in the electrode. Increasing the H2O fraction in the H2–H2O fuel mixture reduced both the three-phase boundary resistance and the gas diffusion resistance for Ni–YSZ; with GDC infiltration, the electrode resistance showed less variation with fuel composition. GDC infiltration improved the performance of fuel-electrode-supported full cells, which yielded a maximum power density of 2.28 W cm−2 in fuel cell mode and an electrolysis current density at 1.3 V of 2.22 A cm−2, both at 800 °C.
- 1 February 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 8 (7) , 4099-4106
Enhancement of Ni–(Y2O3)0.08(ZrO2)0.92 fuel electrode performance by infiltration of Ce0.8Gd0.2O2−δ nanoparticles
This paper addresses the use of Ce0.8Gd0.2O2−δ (GDC) infiltration into the Ni–(Y2O3)0.08(ZrO2)0.92 (YSZ) fuel electrode of solid oxide cells (SOCs) for improving their electrochemical performance in fuel cell and electrolysis operation. Although doped ceria infiltration into Ni–YSZ has recently been shown to improve the electrode performance and stability, the mechanisms defining how GDC impacts electrochemical characteristics are not fully delineated. Furthermore, the electrochemical characteristics have not yet been determined over the full range of conditions normally encountered in fuel cell and electrolysis operation. Here we present a study of both symmetric and full cells aimed at understanding the electrochemical mechanisms of GDC-modified Ni–YSZ over a wide range of fuel compositions and temperatures. Single-step GDC infiltration at an appropriate loading substantially reduced the polarization resistance of Ni–YSZ electrodes in electrolyte-supported cells, as measured using electrochemical impedance spectroscopy (EIS) at various temperatures (600–800 °C) in a range of H2O–H2 mixtures (3–90 vol% H2O). Fuel-electrode-supported cells had significant concentration polarization due to the thick Ni–YSZ supports. A distribution of relaxation times approach is used to develop a physically-based electrochemical model; the results show that GDC reduces the reaction resistance associated with three-phase boundaries, but also appears to improve oxygen transport in the electrode. Increasing the H2O fraction in the H2–H2O fuel mixture reduced both the three-phase boundary resistance and the gas diffusion resistance for Ni–YSZ; with GDC infiltration, the electrode resistance showed less variation with fuel composition. GDC infiltration improved the performance of fuel-electrode-supported full cells, which yielded a maximum power density of 2.28 W cm−2 in fuel cell mode and an electrolysis current density at 1.3 V of 2.22 A cm−2, both at 800 °C.
- 3 September 2019
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 7 (37) , 21447-21458
High stability SrTi1−xFexO3−δ electrodes for oxygen reduction and oxygen evolution reactions
Sr(Ti1−xFex)O3−δ (STF) has been explored as a high stable oxygen electrode for oxygen reduction and oxygen evolution reactions.
- 3 September 2019
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 7 (37) , 21447-21458
High stability SrTi1−xFexO3−δ electrodes for oxygen reduction and oxygen evolution reactions
Sr(Ti1−xFex)O3−δ (STF) has been explored as a high stable oxygen electrode for oxygen reduction and oxygen evolution reactions.