Yubo Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Yubo Zhang has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Jason D. Nicholas
Michigan State University
5 shared publications - Kevin Huang
University of South Carolina
3 shared publications Yeting Wen
University of South Carolina
3 shared publications- Dalton Cox
Northwestern University
2 shared publications - Jakob Michael Reinke
Northwestern University
2 shared publications - Scott Alexander Barnett
Northwestern University
2 shared publications
Latest Publications
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (54) , 372
Zirconia Overcoats and Ceria Nanoparticles Do Not Improve the 650oC Stability of LSCF-Infiltrated Solid Oxide Cell Electrodes More When Used Together
Nano-composite electrodes fabricated by introducing nano-sized mixed ionic and electronic conducting (MIEC) catalysts into partially-sintered micro-sized ionic conducting backbones have been used by many researchers to improve the electrochemical performance, and/or reduce the operating temperature, of Solid Oxide Cells (SOCs).1 Unfortunately, these infiltrated electrodes have often possessed poor electrochemical performance stability.2 This presentation will review recent results showing how pre-infiltrated ceria nano-particles3 or atomic layer deposited zirconia overcoats4 can be used as on-board Sr getters to increase the long-term stability of La0.6Sr0.4Co0.8Fe0.2O3-x (LSCF)-infiltrated Ce0.9Gd0.1O1.95-x (GDC) SOC electrodes, without compromising initial performance. This talk will also present results showing that when combined, these surface modification techniques result in LSCF-GDC performance degradation rates that are no better than those obtained from each technique used separately. Lastly, this talk will present GDC pre-infiltration results supporting a newly-emerging consensus that Sr does not surface segregate in Sm0.5Sr0.5CoO3-x (SSC) like it does in LSCF. References D. Ding, X. X. Li, S. Y. Lai, K. Gerdes and M. L. Liu, Energy Environ. Sci., 7, 552 (2014). M. Shah, P. W. Voorhees and S. A. Barnett, Solid State Ionics, 187, 64 (2011). Y. Zhang and J. D. Nicholas, Journal of the Electrochemical Society, 168, 024522 (2021). Y. Zhang, Y. Wen, K. Huang and J. D. Nicholas, ACS Applied Energy Materials, 3, 4057 (2020).
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (54) , 372
Zirconia Overcoats and Ceria Nanoparticles Do Not Improve the 650oC Stability of LSCF-Infiltrated Solid Oxide Cell Electrodes More When Used Together
Nano-composite electrodes fabricated by introducing nano-sized mixed ionic and electronic conducting (MIEC) catalysts into partially-sintered micro-sized ionic conducting backbones have been used by many researchers to improve the electrochemical performance, and/or reduce the operating temperature, of Solid Oxide Cells (SOCs).1 Unfortunately, these infiltrated electrodes have often possessed poor electrochemical performance stability.2 This presentation will review recent results showing how pre-infiltrated ceria nano-particles3 or atomic layer deposited zirconia overcoats4 can be used as on-board Sr getters to increase the long-term stability of La0.6Sr0.4Co0.8Fe0.2O3-x (LSCF)-infiltrated Ce0.9Gd0.1O1.95-x (GDC) SOC electrodes, without compromising initial performance. This talk will also present results showing that when combined, these surface modification techniques result in LSCF-GDC performance degradation rates that are no better than those obtained from each technique used separately. Lastly, this talk will present GDC pre-infiltration results supporting a newly-emerging consensus that Sr does not surface segregate in Sm0.5Sr0.5CoO3-x (SSC) like it does in LSCF. References D. Ding, X. X. Li, S. Y. Lai, K. Gerdes and M. L. Liu, Energy Environ. Sci., 7, 552 (2014). M. Shah, P. W. Voorhees and S. A. Barnett, Solid State Ionics, 187, 64 (2011). Y. Zhang and J. D. Nicholas, Journal of the Electrochemical Society, 168, 024522 (2021). Y. Zhang, Y. Wen, K. Huang and J. D. Nicholas, ACS Applied Energy Materials, 3, 4057 (2020).
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (54) , 79
Phase Stability of SrTi1-XFexO3- δ Under Solid Oxide Cell Fuel-Electrode Conditions: Implications for Related Exsolution Electrode Materials
Perovskite oxides with catalytically active metal nanoparticle exsolution are receiving considerable attention as alternative Solid Oxide Cell fuel-electrode materials. For exsolution, a small amount of a cation is substituted on the B-site of the base oxide and then is reduced out of the host lattice to form nanoparticles that promote electrochemical processes. During exsolution, the host lattice generally becomes more B-site deficient. In some cases, the oxide is made initially A-site deficient to compensate for the loss of B-site cations. Thus, the stability of these oxides under a range of stoichiometries and fuel electrode conditions is of interest. Here we focus on one perovskite host material of interest, SrTi1-xFexO3- δ (STF), which has shown good fuel electrode characteristics that can be enhanced by the substitution of Ru or Ni, resulting in exsolution to form Ru-Fe or Ni-Fe alloy nanoparticles, respectively. (1, 2) Although the amounts of Ru or Ni substituted are small, typically ~ 7% of the B-site cations, the co-exsolution of a comparable amount of Fe is usually observed, resulting in substantial B-site deficiency, potentially de-stabilizing the host perovskite phase. The stability of Fe in STF is also of interest because it helps to determine the Fe content of the alloy nanoparticles. (3) This study seeks to determine the stability of STF in various reducing fuel environments. While STF has been mostly studied as SrTi0.3Fe0.7O3-δ (STF-7), it is not known if this composition provides the best combination of stability and electrochemical performance. Thus, a few additional compositions, SrTi0.5Fe0.5O3- δ (STF-5), SrTi0.4Fe0.6O3- δ (STF-6), and SrTi0.2Fe0.8O3- δ (STF-8), have been studied. In general, the Fe-rich compositions are expected to possess higher electronic and ionic conductivity, leading to good electrochemical performance, whereas the more Ti-rich compositions are expected to provide better stability. Exposure to 97% H2 – 3% H2O at 850°C for 4 h resulted in STF decomposition into BCC α-Fe and a Ruddlesden-Popper (RP) phase, but the decomposition became more limited for the more Ti-rich compositions (Figure 1a). The main Fe peak overlaps with one of the RP peaks, but the presence of α-Fe particles is clearly visible in STEM energy dispersive x-ray spectroscopy chemical mapping, shown for STF-7 in Figure 1b. Figure 1c shows that there is a critical p(O2), 1.3 x 10-20 atm, below which decomposition of perovskite STF-7 occurs. In addition to ex situ XRD as shown in Figure 1, in situ XRD results will be presented and used to confirm and quantify phase changes in combination with thermogravimetric analysis (TGA). Additionally, the conductivity and electrochemical performance of the various STF compositions will be reported and discussed relative to the phase change from perovskite to Ruddlesden Popper and the Fe exsolution. The other main materials variable to be explored is the A-to-B site stoichiometry, which will be studied over the range expected during exsolution. The implications of these results for various exsolution electrode compositions will be discussed. Figure 1: a) Reductions of STF-5 through STF-8 all yield significant decomposition as the initially pristine perovskite acquires several additional peaks. b) Using energy dispersive x-ray spectroscopy, it can be shown that significant Fe deposits appear in STF-7 after reduction at 850°C (effective pO2 1.2e-21 atm for 4 hours). c By increasing pO2 by a factor of 10, XRD patterns for STF-7 show no clear Ruddlesden-Popper or α-Fe peaks, indicating that decomposition requires significantly reducing conditions and that STF may remain stable under more oxidizing conditions. References R. Glaser, T. Zhu, H. Troiani, A. Caneiro, L. Mogni and S. Barnett, Journal of Materials Chemistry A, 6, 5193 (2018). T. Zhu, H. Troiani, L. V. Mogni, M. Santaya, M. Han and S. A. Barnett, Journal of Power Sources, 439 (2019). T. Zhu, H. E. Troiani, L. V. Mogni, M. Han and S. A. Barnett, Joule, 2, 478 (2018). Figure 1
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (54) , 79
Phase Stability of SrTi1-XFexO3- δ Under Solid Oxide Cell Fuel-Electrode Conditions: Implications for Related Exsolution Electrode Materials
Perovskite oxides with catalytically active metal nanoparticle exsolution are receiving considerable attention as alternative Solid Oxide Cell fuel-electrode materials. For exsolution, a small amount of a cation is substituted on the B-site of the base oxide and then is reduced out of the host lattice to form nanoparticles that promote electrochemical processes. During exsolution, the host lattice generally becomes more B-site deficient. In some cases, the oxide is made initially A-site deficient to compensate for the loss of B-site cations. Thus, the stability of these oxides under a range of stoichiometries and fuel electrode conditions is of interest. Here we focus on one perovskite host material of interest, SrTi1-xFexO3- δ (STF), which has shown good fuel electrode characteristics that can be enhanced by the substitution of Ru or Ni, resulting in exsolution to form Ru-Fe or Ni-Fe alloy nanoparticles, respectively. (1, 2) Although the amounts of Ru or Ni substituted are small, typically ~ 7% of the B-site cations, the co-exsolution of a comparable amount of Fe is usually observed, resulting in substantial B-site deficiency, potentially de-stabilizing the host perovskite phase. The stability of Fe in STF is also of interest because it helps to determine the Fe content of the alloy nanoparticles. (3) This study seeks to determine the stability of STF in various reducing fuel environments. While STF has been mostly studied as SrTi0.3Fe0.7O3-δ (STF-7), it is not known if this composition provides the best combination of stability and electrochemical performance. Thus, a few additional compositions, SrTi0.5Fe0.5O3- δ (STF-5), SrTi0.4Fe0.6O3- δ (STF-6), and SrTi0.2Fe0.8O3- δ (STF-8), have been studied. In general, the Fe-rich compositions are expected to possess higher electronic and ionic conductivity, leading to good electrochemical performance, whereas the more Ti-rich compositions are expected to provide better stability. Exposure to 97% H2 – 3% H2O at 850°C for 4 h resulted in STF decomposition into BCC α-Fe and a Ruddlesden-Popper (RP) phase, but the decomposition became more limited for the more Ti-rich compositions (Figure 1a). The main Fe peak overlaps with one of the RP peaks, but the presence of α-Fe particles is clearly visible in STEM energy dispersive x-ray spectroscopy chemical mapping, shown for STF-7 in Figure 1b. Figure 1c shows that there is a critical p(O2), 1.3 x 10-20 atm, below which decomposition of perovskite STF-7 occurs. In addition to ex situ XRD as shown in Figure 1, in situ XRD results will be presented and used to confirm and quantify phase changes in combination with thermogravimetric analysis (TGA). Additionally, the conductivity and electrochemical performance of the various STF compositions will be reported and discussed relative to the phase change from perovskite to Ruddlesden Popper and the Fe exsolution. The other main materials variable to be explored is the A-to-B site stoichiometry, which will be studied over the range expected during exsolution. The implications of these results for various exsolution electrode compositions will be discussed. Figure 1: a) Reductions of STF-5 through STF-8 all yield significant decomposition as the initially pristine perovskite acquires several additional peaks. b) Using energy dispersive x-ray spectroscopy, it can be shown that significant Fe deposits appear in STF-7 after reduction at 850°C (effective pO2 1.2e-21 atm for 4 hours). c By increasing pO2 by a factor of 10, XRD patterns for STF-7 show no clear Ruddlesden-Popper or α-Fe peaks, indicating that decomposition requires significantly reducing conditions and that STF may remain stable under more oxidizing conditions. References R. Glaser, T. Zhu, H. Troiani, A. Caneiro, L. Mogni and S. Barnett, Journal of Materials Chemistry A, 6, 5193 (2018). T. Zhu, H. Troiani, L. V. Mogni, M. Santaya, M. Han and S. A. Barnett, Journal of Power Sources, 439 (2019). T. Zhu, H. E. Troiani, L. V. Mogni, M. Han and S. A. Barnett, Joule, 2, 478 (2018). Figure 1
- 19 May 2023
- Published by The Electrochemical Society in ECS Transactions
- Vol. 111 (6) , 2413-2424
Zirconia Overcoats and Ceria Nanoparticles Do Not Improve the 650oC Stability of LSCF-Infiltrated Solid Oxide Cell Electrodes More When Used Together
Previously, porous 1-5 nm thick atomic layer deposited (ALD) zirconia overcoats or pre-infiltrated gadolinium doped ceria (GDC) nanoparticles were shown to independently improve La0.6Sr0.4Co0.8Fe0.2O3-x (LSCF)-infiltrated Solid Oxide Cell (SOC) oxygen electrode stability (without deteriorating initial performance) by chemically gettering interfacial Sr from the LSCF interfaces. Unfortunately, the experiments here showed that the deposition of porous 1-5 nm thick ALD zirconia overcoats on GDC-pre-infiltrated LSCF-GDC electrodes did not lead to larger-than-previously-achieved improvements in the initial 650oC polarization resistance (RP ) or open-circuit 1000-hour 650oC RP degradation rate. Electrochemical Impedance Spectroscopy (EIS) modeling indicated that in all cases the observed degradation was consistent with increased oxygen exchange resistance at the LSFC-GDC and LSCF-air interfaces caused by enhanced Sr segregation, while Scanning Electron Microscopy (SEM) results showed that the observed degradation was not the result of infiltrate particle coarsening. X-ray Photoelectron Spectroscopy also suggested that in zirconia overcoated GDC pre-infiltrated cells, Sr was mainly gettered by zirconia overcoats that may have been compromised by the pre-infiltrated GDC.
- 19 May 2023
- Published by The Electrochemical Society in ECS Transactions
- Vol. 111 (6) , 2413-2424
Zirconia Overcoats and Ceria Nanoparticles Do Not Improve the 650oC Stability of LSCF-Infiltrated Solid Oxide Cell Electrodes More When Used Together
Previously, porous 1-5 nm thick atomic layer deposited (ALD) zirconia overcoats or pre-infiltrated gadolinium doped ceria (GDC) nanoparticles were shown to independently improve La0.6Sr0.4Co0.8Fe0.2O3-x (LSCF)-infiltrated Solid Oxide Cell (SOC) oxygen electrode stability (without deteriorating initial performance) by chemically gettering interfacial Sr from the LSCF interfaces. Unfortunately, the experiments here showed that the deposition of porous 1-5 nm thick ALD zirconia overcoats on GDC-pre-infiltrated LSCF-GDC electrodes did not lead to larger-than-previously-achieved improvements in the initial 650oC polarization resistance (RP ) or open-circuit 1000-hour 650oC RP degradation rate. Electrochemical Impedance Spectroscopy (EIS) modeling indicated that in all cases the observed degradation was consistent with increased oxygen exchange resistance at the LSFC-GDC and LSCF-air interfaces caused by enhanced Sr segregation, while Scanning Electron Microscopy (SEM) results showed that the observed degradation was not the result of infiltrate particle coarsening. X-ray Photoelectron Spectroscopy also suggested that in zirconia overcoated GDC pre-infiltrated cells, Sr was mainly gettered by zirconia overcoats that may have been compromised by the pre-infiltrated GDC.
- 19 May 2023
- Published by The Electrochemical Society in ECS Transactions
- Vol. 111 (6) , 475-483
Phase Stability of SrTi1-XFexO3- δ Under Solid Oxide Cell Fuel-Electrode Conditions: Implications for Related Exsolution Electrode Materials
SrTi1-xFexO3-δ (STF) has shown promise as a fuel electrode, and as a basis for fuel electrodes with catalytically active nanoparticle exsolution. This study aims to determine trends in performance and stability of STF in highly reducing environments as Fe-content is varied from x = 0.5 to 0.8. Here we report that, while polarization resistance of STF fuel electrodes decreases with higher Fe-content, this is accompanied with lower stability in highly reducing conditions. For too-reducing conditions and too-high x, partial decomposition of the original perovskite phase is observed with the formation of metallic Fe and a Ruddlesden-Popper STF phase.
- 19 May 2023
- Published by The Electrochemical Society in ECS Transactions
- Vol. 111 (6) , 475-483
Phase Stability of SrTi1-XFexO3- δ Under Solid Oxide Cell Fuel-Electrode Conditions: Implications for Related Exsolution Electrode Materials
SrTi1-xFexO3-δ (STF) has shown promise as a fuel electrode, and as a basis for fuel electrodes with catalytically active nanoparticle exsolution. This study aims to determine trends in performance and stability of STF in highly reducing environments as Fe-content is varied from x = 0.5 to 0.8. Here we report that, while polarization resistance of STF fuel electrodes decreases with higher Fe-content, this is accompanied with lower stability in highly reducing conditions. For too-reducing conditions and too-high x, partial decomposition of the original perovskite phase is observed with the formation of metallic Fe and a Ruddlesden-Popper STF phase.
- 9 October 2022
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2022-02 (47) , 1777
On-Board Strontium Getters for Improved Solid Oxide Cell Durability
Nano-composite electrodes fabricated by introducing nano-sized mixed ionic and electronic conducting (MIEC) catalysts into partially-sintered micro-sized ionic conducting backbones have been used by many researchers to improve the electrochemical performance, and/or reduce the operating temperature, of Solid Oxide Cells (SOCs).1 Unfortunately, these infiltrated electrodes have often possessed poor electrochemical performance stability.2 This presentation will review recent results showing how pre-infiltrated ceria nano-particles3 or atomic layer deposited zirconia overcoats4 can be used as on-board Sr getters to increase the long-term stability of La0.6Sr0.4Co0.8Fe0.2O3-x (LSCF)-infiltrated Ce0.9Gd0.1O1.95-x (GDC) SOC electrodes, without compromising initial performance. This talk will also present results showing that when combined, these surface modification techniques result in LSCF-GDC performance degradation rates that are no better than those obtained from each technique used separately. Lastly, this talk will present GDC pre-infiltration results supporting a newly-emerging consensus that Sr does not surface segregate in Sm0.5Sr0.5CoO3-x (SSC) like it does in LSCF. References D. Ding, X. X. Li, S. Y. Lai, K. Gerdes and M. L. Liu, Energy Environ. Sci., 7, 552 (2014). M. Shah, P. W. Voorhees and S. A. Barnett, Solid State Ionics, 187, 64 (2011). Y. Zhang and J. D. Nicholas, Journal of the Electrochemical Society, 168, 024522 (2021). Y. Zhang, Y. Wen, K. Huang and J. D. Nicholas, ACS Applied Energy Materials, 3, 4057 (2020).
- 9 October 2022
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2022-02 (47) , 1777
On-Board Strontium Getters for Improved Solid Oxide Cell Durability
Nano-composite electrodes fabricated by introducing nano-sized mixed ionic and electronic conducting (MIEC) catalysts into partially-sintered micro-sized ionic conducting backbones have been used by many researchers to improve the electrochemical performance, and/or reduce the operating temperature, of Solid Oxide Cells (SOCs).1 Unfortunately, these infiltrated electrodes have often possessed poor electrochemical performance stability.2 This presentation will review recent results showing how pre-infiltrated ceria nano-particles3 or atomic layer deposited zirconia overcoats4 can be used as on-board Sr getters to increase the long-term stability of La0.6Sr0.4Co0.8Fe0.2O3-x (LSCF)-infiltrated Ce0.9Gd0.1O1.95-x (GDC) SOC electrodes, without compromising initial performance. This talk will also present results showing that when combined, these surface modification techniques result in LSCF-GDC performance degradation rates that are no better than those obtained from each technique used separately. Lastly, this talk will present GDC pre-infiltration results supporting a newly-emerging consensus that Sr does not surface segregate in Sm0.5Sr0.5CoO3-x (SSC) like it does in LSCF. References D. Ding, X. X. Li, S. Y. Lai, K. Gerdes and M. L. Liu, Energy Environ. Sci., 7, 552 (2014). M. Shah, P. W. Voorhees and S. A. Barnett, Solid State Ionics, 187, 64 (2011). Y. Zhang and J. D. Nicholas, Journal of the Electrochemical Society, 168, 024522 (2021). Y. Zhang, Y. Wen, K. Huang and J. D. Nicholas, ACS Applied Energy Materials, 3, 4057 (2020).
- Open Access
- 1 March 2021
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 168 (3) , 034513
Updating the Notion that Poor Cathode Performance Typically Dominates Overall Solid Oxide Fuel Cell Response
Here, Solid Oxide Fuel Cells (SOFCs) utilizing high performance La0.6Sr0.4Co0.8Fe0.2O3−x (LSCF)—Gd0.1Ce0.9O1.95−x (GDC) nano-composite cathodes (NCCs) on commercially-available [GDC diffusion barrier ∣ (Y2O3)0.08(ZrO2)0.92 (YSZ) electrolyte ∣ Ni-YSZ anode functional layer ∣ Ni-YSZ gas transport layer] supports had the same 550 °C–650 °C current-voltage behavior as identical SOFCs utilizing commercial La0.6Sr0.4CoO3 (LSC) cathodes, despite differences in open-circuit cathode polarization resistance (R P ). Nickel anode infiltration also produced a ∼25% SOFC peak power density improvement in these cells. These results, combined with literature data showing that either the cathode R P , anode R P , or ohmic losses within the cell can limit state-of-the-art SOFC performance (depending on the exact compositions, microstructures, testing conditions etc.), suggest that it is time to retire the old adage that poor cathode performance typically limits overall SOFC performance.
- 1 March 2021
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 168 (3) , 034513
Open AccessUpdating the Notion that Poor Cathode Performance Typically Dominates Overall Solid Oxide Fuel Cell Response
Here, Solid Oxide Fuel Cells (SOFCs) utilizing high performance La0.6Sr0.4Co0.8Fe0.2O3−x (LSCF)—Gd0.1Ce0.9O1.95−x (GDC) nano-composite cathodes (NCCs) on commercially-available [GDC diffusion barrier ∣ (Y2O3)0.08(ZrO2)0.92 (YSZ) electrolyte ∣ Ni-YSZ anode functional layer ∣ Ni-YSZ gas transport layer] supports had the same 550 °C–650 °C current-voltage behavior as identical SOFCs utilizing commercial La0.6Sr0.4CoO3 (LSC) cathodes, despite differences in open-circuit cathode polarization resistance (R P ). Nickel anode infiltration also produced a ∼25% SOFC peak power density improvement in these cells. These results, combined with literature data showing that either the cathode R P , anode R P , or ohmic losses within the cell can limit state-of-the-art SOFC performance (depending on the exact compositions, microstructures, testing conditions etc.), suggest that it is time to retire the old adage that poor cathode performance typically limits overall SOFC performance.