Mirko Kariž
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mirko Kariž has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
- Manja Kitek Kuzman
University of Ljubljana
11 shared publications - Daša Krapež Tomec
Biotechnical Faculty, University of Ljubljana, Jamnikarjeva 101, 1000 Ljubljana, Slovenia
9 shared publications Manja Kitek Kuzman
Department of Wood Science and Technology, Biotechnical Faculty, University of Ljubljana, Ljubljana, Slovenia
7 shared publications- Jure Žigon
University of Ljubljana
5 shared publications Milan Sernek
5 shared publications- Milan Šernek
Department of Wood Science and Technology, Biotechnical Faculty, University of Ljubljana, Ljubljana, Slovenia
5 shared publications
Latest Publications
- Open Access
- 21 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (8) , 4016
The Durability of 3D-Printed Furniture Connectors Made from Different Materials
The use of 3D-printed parts is becoming increasingly widespread, including in the furniture industry. Furniture products are subjected to various loads during use. Therefore, it is important to know their maximum allowable static loads and their maximum allowable cyclic loads, which are lower and depend on design and material properties. In this study, simple 3D FFF printed connectors intended as shelf connectors and made of three different materials (ABS, PLA, Wood–PLA) were subjected to different forces under static and cyclic loading until failure. Connectors made of ABS withstand the highest static load (346 N), followed by connectors made of PLA (195 N) and Wood–PLA (136 N). The fatigue behaviour of the tested connectors also depended on the material used. Connectors made of ABS exhibit the highest static load, but the stresses must be significantly lower under cyclic loading. For example, connectors made of ABS can withstand 50,000 cycles with a load of less than 25% of their maximum static load, while connectors made of PLA can withstand the same number of cycles with a load of 44% of their maximum static load. Connectors made of Wood–PLA achieved 50,000 cycles at a load of 63% of their maximum load. PLA and Wood–PLA were more durable relative to their maximum strength, even though ABS could carry heavier absolute loads. These findings could support the design of material-efficient furniture connectors with respect to their expected maximum loads and required durability; however, the results should be interpreted as preliminary and indicative of comparative trends rather than statistically validated fatigue data.
- 21 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (8) , 4016
Open AccessThe Durability of 3D-Printed Furniture Connectors Made from Different Materials
The use of 3D-printed parts is becoming increasingly widespread, including in the furniture industry. Furniture products are subjected to various loads during use. Therefore, it is important to know their maximum allowable static loads and their maximum allowable cyclic loads, which are lower and depend on design and material properties. In this study, simple 3D FFF printed connectors intended as shelf connectors and made of three different materials (ABS, PLA, Wood–PLA) were subjected to different forces under static and cyclic loading until failure. Connectors made of ABS withstand the highest static load (346 N), followed by connectors made of PLA (195 N) and Wood–PLA (136 N). The fatigue behaviour of the tested connectors also depended on the material used. Connectors made of ABS exhibit the highest static load, but the stresses must be significantly lower under cyclic loading. For example, connectors made of ABS can withstand 50,000 cycles with a load of less than 25% of their maximum static load, while connectors made of PLA can withstand the same number of cycles with a load of 44% of their maximum static load. Connectors made of Wood–PLA achieved 50,000 cycles at a load of 63% of their maximum load. PLA and Wood–PLA were more durable relative to their maximum strength, even though ABS could carry heavier absolute loads. These findings could support the design of material-efficient furniture connectors with respect to their expected maximum loads and required durability; however, the results should be interpreted as preliminary and indicative of comparative trends rather than statistically validated fatigue data.
- Open Access
- 11 July 2025
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 21 (5) , 1-9
Thermally modified beech wood in polylactic acid filaments for 3D printing: morphology of printed parts and dynamic mechanical analysis of injection-moulded specimens
- 11 July 2025
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 21 (5) , 1-9
Open AccessThermally modified beech wood in polylactic acid filaments for 3D printing: morphology of printed parts and dynamic mechanical analysis of injection-moulded specimens
- Open Access
- 15 February 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (4) , 2046
Effect of Filament Material and Printing Temperature on 3D Printing Extrusion Force
In this study, a modified 3D printer hotend equipped with a load cell, attached to the feeding system, was used to evaluate the effects of filament material composition and printing parameters on the extrusion force required. Four different materials (commercial PLA, pure PLA, wood-PLA with different ratios of wood particles, and wood-PLA with different ratios of thermally modified wood particles) were used for 3D printing, and the feeding resistance was measured. The filament feeder was connected to the extruder hotend via a load cell, which measured the forces required to push the filament through the extruder and the nozzle. Three printing nozzle temperatures of 200, 210, and 220 °C were used. The results show that the printing temperature and the material influence the required extrusion forces, which varied between 1 and 8 N, but the variation was high. With proper optimization and integration into the printer firmware, this setup could also be used to detect nozzle clogging during printing, modify printing parameters during the process, and prevent the uneven extrusion of composite filaments.
- 15 February 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (4) , 2046
Open AccessEffect of Filament Material and Printing Temperature on 3D Printing Extrusion Force
In this study, a modified 3D printer hotend equipped with a load cell, attached to the feeding system, was used to evaluate the effects of filament material composition and printing parameters on the extrusion force required. Four different materials (commercial PLA, pure PLA, wood-PLA with different ratios of wood particles, and wood-PLA with different ratios of thermally modified wood particles) were used for 3D printing, and the feeding resistance was measured. The filament feeder was connected to the extruder hotend via a load cell, which measured the forces required to push the filament through the extruder and the nozzle. Three printing nozzle temperatures of 200, 210, and 220 °C were used. The results show that the printing temperature and the material influence the required extrusion forces, which varied between 1 and 8 N, but the variation was high. With proper optimization and integration into the printer firmware, this setup could also be used to detect nozzle clogging during printing, modify printing parameters during the process, and prevent the uneven extrusion of composite filaments.
- Open Access
The Effects of Microcrystalline Cellulose Addition on the Properties of Wood–PLA Filaments for 3D Printing
This paper describes the use of microcrystalline cellulose (MCC) as an additive in wood-polylactic acid (PLA) filaments suitable for 3D printing. Filaments prepared with PLA, thermally modified (TM) wood, and three different MCC loadings (1, 3, and 5 wt%) by two-step melt blending in the extruder were characterized with respect to their rheological, thermal, and mechanical response. The analyses demonstrate that a low MCC content (1%) improves the mobility of the polymer chains and contributes to a higher elasticity of the matrix chain, a higher crystallinity, a lower glass transition temperature (by 1.66 °C), and a lower melting temperature (by 1.31 °C) and leads to a higher tensile strength (1.2%) and a higher modulus of elasticity (12.1%). Higher MCC loading hinders the mobility of the polymer matrix and leads to a rearrangement of the crystal lattice structure, resulting in a decrease in crystallinity. Scanning electron micrographs show that the cellulose is well distributed and dispersed in the PLA matrix, with some agglomeration occurring at higher MCC levels. The main objective of this study was to develop and evaluate a filament containing an optimal amount of MCC to improve compatibility between wood and PLA, optimize melt processability, and improve mechanical properties. It can be concluded that a 1% addition of MCC favorably changes the properties of the wood–PLA filaments, while a higher MCC content does not have this effect.
Open AccessThe Effects of Microcrystalline Cellulose Addition on the Properties of Wood–PLA Filaments for 3D Printing
This paper describes the use of microcrystalline cellulose (MCC) as an additive in wood-polylactic acid (PLA) filaments suitable for 3D printing. Filaments prepared with PLA, thermally modified (TM) wood, and three different MCC loadings (1, 3, and 5 wt%) by two-step melt blending in the extruder were characterized with respect to their rheological, thermal, and mechanical response. The analyses demonstrate that a low MCC content (1%) improves the mobility of the polymer chains and contributes to a higher elasticity of the matrix chain, a higher crystallinity, a lower glass transition temperature (by 1.66 °C), and a lower melting temperature (by 1.31 °C) and leads to a higher tensile strength (1.2%) and a higher modulus of elasticity (12.1%). Higher MCC loading hinders the mobility of the polymer matrix and leads to a rearrangement of the crystal lattice structure, resulting in a decrease in crystallinity. Scanning electron micrographs show that the cellulose is well distributed and dispersed in the PLA matrix, with some agglomeration occurring at higher MCC levels. The main objective of this study was to develop and evaluate a filament containing an optimal amount of MCC to improve compatibility between wood and PLA, optimize melt processability, and improve mechanical properties. It can be concluded that a 1% addition of MCC favorably changes the properties of the wood–PLA filaments, while a higher MCC content does not have this effect.
- Open Access
- 15 February 2024
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 19 (6) , 1251-1265
Effect of thermal modification of wood on the rheology, mechanical properties and dimensional stability of wood composite filaments and 3D-printed parts
- 15 February 2024
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 19 (6) , 1251-1265
Open AccessEffect of thermal modification of wood on the rheology, mechanical properties and dimensional stability of wood composite filaments and 3D-printed parts
- Open Access
- 9 December 2023
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 82 (2) , 403-416
Effect of thermal modification of wood particles for wood-PLA composites on properties of filaments, 3D-printed parts and injection moulded parts
This paper describes the development and characterisation of wood-filled polylactic acid (PLA) composite filaments for application in fused filament fabrication three-dimensional (3D) printing. Four different wood-polymer composite filaments for 3D printing were prepared, and specimens were 3D-printed with the obtained materials. The composite filaments consisted of wood particles (10% or 20% mass ratio) and a PLA polymer matrix. Wood particles were prepared by grinding and sieving non-modified beech wood and thermally modified (TM) (at 200 °C) beech wood. Thermal modification of wood affected particle preparation and smaller particles with lower aspect ratios were obtained. Filaments with TM wood particles were extruded better than with non-modified wood particles, with lower surface roughness and lower porosity. With a higher wood ratio, the surface roughness and porosity of the filament increased. Non-homogenous filaments also affected extrusion in 3D printing and reduced the properties of 3D-printed parts. Parts 3D-printed from filaments with TM particles had better tensile strength than from filaments with non-modified particles, but were lower than from pure PLA filaments. The tensile strength of the injection-moulded specimens was 18–69% higher than that of the 3D-printed specimens, depending on the filament composition. The results indicate some positive effects of thermal modification of wood particles on the properties of filaments and 3D-printed parts. Nevertheless, further optimisation of particle preparation and extrusion parameters is needed to obtain quality filaments with this size of wood particles.
- 9 December 2023
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 82 (2) , 403-416
Open AccessEffect of thermal modification of wood particles for wood-PLA composites on properties of filaments, 3D-printed parts and injection moulded parts
This paper describes the development and characterisation of wood-filled polylactic acid (PLA) composite filaments for application in fused filament fabrication three-dimensional (3D) printing. Four different wood-polymer composite filaments for 3D printing were prepared, and specimens were 3D-printed with the obtained materials. The composite filaments consisted of wood particles (10% or 20% mass ratio) and a PLA polymer matrix. Wood particles were prepared by grinding and sieving non-modified beech wood and thermally modified (TM) (at 200 °C) beech wood. Thermal modification of wood affected particle preparation and smaller particles with lower aspect ratios were obtained. Filaments with TM wood particles were extruded better than with non-modified wood particles, with lower surface roughness and lower porosity. With a higher wood ratio, the surface roughness and porosity of the filament increased. Non-homogenous filaments also affected extrusion in 3D printing and reduced the properties of 3D-printed parts. Parts 3D-printed from filaments with TM particles had better tensile strength than from filaments with non-modified particles, but were lower than from pure PLA filaments. The tensile strength of the injection-moulded specimens was 18–69% higher than that of the 3D-printed specimens, depending on the filament composition. The results indicate some positive effects of thermal modification of wood particles on the properties of filaments and 3D-printed parts. Nevertheless, further optimisation of particle preparation and extrusion parameters is needed to obtain quality filaments with this size of wood particles.
- Open Access
- 17 June 2022
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 18 (3) , 870-883
Strength and stiffness of 3D-printed connectors compared with the wooden mortise and tenon joints for chairs
In this study, 3D-printed connectors to replace the typical L-shaped joints in the construction of a chair were developed, tested and numerically analysed. Different connectors were designed and manufactured with a fused deposition modelling (FDM) 3D printer using acrylonitrile butadiene styrene (ABS) with the aim to find a simple shaped connector which could be used to build chairs and withstand standard chair loading requirements. The strength and stiffness of the joints were tested and compared with traditional beech mortise-and-tenon joints. Numerical stress and strain analyses were performed with the finite element method for an orthotropic linear-elastic model. The experimental results showed that joints with 3D-printed connectors achieved lower strength than the traditional wooden mortise-and-tenon joints with similar dimensions. The results indicate that the effect of reinforcement of the connector were not recognised due to the small thickness and inadequate geometric position and arrangement of the reinforcement ABS material. The chair assembled with 3D-printed connectors could withstand the loads for seating, but failed the backrest test according to standard EN 1728:2002. The connectors need to be optimised and reinforced to withstand standard loads.
- 17 June 2022
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 18 (3) , 870-883
Open AccessStrength and stiffness of 3D-printed connectors compared with the wooden mortise and tenon joints for chairs
In this study, 3D-printed connectors to replace the typical L-shaped joints in the construction of a chair were developed, tested and numerically analysed. Different connectors were designed and manufactured with a fused deposition modelling (FDM) 3D printer using acrylonitrile butadiene styrene (ABS) with the aim to find a simple shaped connector which could be used to build chairs and withstand standard chair loading requirements. The strength and stiffness of the joints were tested and compared with traditional beech mortise-and-tenon joints. Numerical stress and strain analyses were performed with the finite element method for an orthotropic linear-elastic model. The experimental results showed that joints with 3D-printed connectors achieved lower strength than the traditional wooden mortise-and-tenon joints with similar dimensions. The results indicate that the effect of reinforcement of the connector were not recognised due to the small thickness and inadequate geometric position and arrangement of the reinforcement ABS material. The chair assembled with 3D-printed connectors could withstand the loads for seating, but failed the backrest test according to standard EN 1728:2002. The connectors need to be optimised and reinforced to withstand standard loads.
- Open Access
Use of Wood in Additive Manufacturing: Review and Future Prospects
Polymers filled with natural-based fillers have shown growing demand/interest in recent years, including in additive manufacturing. Like most natural fillers in 3D printing, wood particles serve mainly as a filler that lowers the cost of the printing material due to their low price. However, could wood be used as a main ingredient to affect/improve the properties of 3D-printed parts? Several advantages, such as its reinforcing ability, biodegradability, availability as waste material from other industries, ability to be used in different forms or only in partial components, recycling options or even the use of its undesirable hydromorph-induced dimensional instability for 4D printing, indicate the importance of exploring its use in 3D printing. A review of publications on 3D printing with wood biomass and technologies involving the use of wood particles and components was conducted to identify the possibilities of using wood in additive technologies and their potential.
Open AccessUse of Wood in Additive Manufacturing: Review and Future Prospects
Polymers filled with natural-based fillers have shown growing demand/interest in recent years, including in additive manufacturing. Like most natural fillers in 3D printing, wood particles serve mainly as a filler that lowers the cost of the printing material due to their low price. However, could wood be used as a main ingredient to affect/improve the properties of 3D-printed parts? Several advantages, such as its reinforcing ability, biodegradability, availability as waste material from other industries, ability to be used in different forms or only in partial components, recycling options or even the use of its undesirable hydromorph-induced dimensional instability for 4D printing, indicate the importance of exploring its use in 3D printing. A review of publications on 3D printing with wood biomass and technologies involving the use of wood particles and components was conducted to identify the possibilities of using wood in additive technologies and their potential.
- Open Access
- 1 January 2022
- Published by Tech Science Press in Journal of Renewable Materials
- Vol. 10 (7) , 1787-1796
The Effect of Printing Parameters and Wood Surface Preparation on the Adhesion of Directly 3D-Printed PLA on Wood
As additive manufacturing technologies advance, new opportunities are opening up for their application in the furniture industry. Wood remains one of the leading raw materials in the furniture industry; therefore, possible options for combining it with 3D printing have been researched. The bonding of 3D-printed polymer parts with wood or 3D printing with wood-plastic composites is already known, but in our research we attempted to directly 3D print polylactic acid (PLA) on wood surfaces. The effect of printing parameters, as well as the surface preparation of wood on the shear strength of the bond between wood and on-printed material was tested. Microscopic images of cross-sections of samples were analyzed. The results show that with a lower initial layer thickness (0.1 mm), a higher printing temperature (220°C), and with the use of polyvinyl acetate (PVAc) primer on the wood surface before 3D printing, a higher bond strength (5.4 MPa) was achieved, but the values for the bond strength remain low compared to the conventional bonding of wood to wood with PVAc adhesive (around 10 MPa). Microscopy studies revealed barely visible penetration of PLA into the lumens of the wood cells. However, the PVAc adhesive used as primer penetrated more into the cell lumens and served as interface layer between deposited melted PLA and the wood, thus creating stronger joints.
- 1 January 2022
- Published by Tech Science Press in Journal of Renewable Materials
- Vol. 10 (7) , 1787-1796
Open AccessThe Effect of Printing Parameters and Wood Surface Preparation on the Adhesion of Directly 3D-Printed PLA on Wood
As additive manufacturing technologies advance, new opportunities are opening up for their application in the furniture industry. Wood remains one of the leading raw materials in the furniture industry; therefore, possible options for combining it with 3D printing have been researched. The bonding of 3D-printed polymer parts with wood or 3D printing with wood-plastic composites is already known, but in our research we attempted to directly 3D print polylactic acid (PLA) on wood surfaces. The effect of printing parameters, as well as the surface preparation of wood on the shear strength of the bond between wood and on-printed material was tested. Microscopic images of cross-sections of samples were analyzed. The results show that with a lower initial layer thickness (0.1 mm), a higher printing temperature (220°C), and with the use of polyvinyl acetate (PVAc) primer on the wood surface before 3D printing, a higher bond strength (5.4 MPa) was achieved, but the values for the bond strength remain low compared to the conventional bonding of wood to wood with PVAc adhesive (around 10 MPa). Microscopy studies revealed barely visible penetration of PLA into the lumens of the wood cells. However, the PVAc adhesive used as primer penetrated more into the cell lumens and served as interface layer between deposited melted PLA and the wood, thus creating stronger joints.
- 24 November 2021
- Published by University of Zagreb, Faculty of Forestry and Wood Technology in Drvna industrija
- Vol. 72 (4) , 381-388
Effect of Artificial Ageing on Adhesive Bonds from Heat Treated Spruce
The influence of artificial ageing on bonded heat-treated spruce lamellas was investigated. Heat-treated spruce lamellas with different degrees of thermal modification were bonded with PVAc and MUF and then exposed to 500 artificial...
- 24 November 2021
- Published by University of Zagreb, Faculty of Forestry and Wood Technology in Drvna industrija
- Vol. 72 (4) , 381-388
Effect of Artificial Ageing on Adhesive Bonds from Heat Treated Spruce
The influence of artificial ageing on bonded heat-treated spruce lamellas was investigated. Heat-treated spruce lamellas with different degrees of thermal modification were bonded with PVAc and MUF and then exposed to 500 artificial...