Yana Alekseevna Gorbyleva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yana Alekseevna Gorbyleva has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Alexander Nikolaevich Drozdov
Natl Univ Oil & Gas Gubkin Univ, Moscow, Russia
5 shared publications - Anatoliy Andreevich Isaev
Sheshmaoil Management Company LLC, 423458 Almetyevsk, Russia
2 shared publications - Karina Shamilyevna Nurgalieva
Department of Development and Operation of Oil and Gas Fields, Saint-Petersburg Mining University, 199106 St. Petersburg, Russia
2 shared publications A. A. Markelova
Peoples Friendship Univ Russia RUDN, Moscow, Russia
1 shared publicationAlexander Drozdov
Peoples' Friendship University of Russia, 117198 Moscow, Russia
1 shared publicationAlexander N. Drozdov
Peoples’ Friendship University of Russia (RUDN University)
1 shared publication
Latest Publications
- 30 September 2023
- Published by Oil Gas Scientific Research Project Institute in SOCAR Proceedings
- No. 3,p. 144-155
Experimental studies on the effect of mixing chamber length on the characteristics of a liquid-gas ejector during the injection of exhaust gases to achieve a water-gas impact on formation
- 30 September 2023
- Published by Oil Gas Scientific Research Project Institute in SOCAR Proceedings
- No. 3,p. 144-155
Experimental studies on the effect of mixing chamber length on the characteristics of a liquid-gas ejector during the injection of exhaust gases to achieve a water-gas impact on formation
- 30 December 2022
- Published by Oil Gas Scientific Research Project Institute in SOCAR Proceedings
- No. SI2,p. 28-36
Application of simultaneous water and gas injection technology for exhaust gas utilization and reduction of CO2 emissions
In today's world, the energy sector has a major impact on the climate. In this process, the share attributable to oil and gas producers is large. The paper shows the prospects of reducing flaring of associated petroleum gas and carbon dioxide emissions by utilization of exhaust (flue) gases for injection into the reservoir to enhance oil recovery. The main industrial sources of exhaust (flue) gases are given. The scope of research on the use of exhaust gases in the development of oil fields with different properties is analyzed. The technology of simultaneous water and gas injection, aimed at the utilization of exhaust gases and increase oil recovery fields, is proposed. The technology of simultaneous water and gas injection is implemented with the use of pump-ejector systems and allows for the simultaneous injection of water and gas into productive formations. The main parameters of pumpejector system are determined for the conditions of a particular field. Keywords: exhaust (fuel) gases utilization; enhanced oil recovery (EOR); SWAG injection; pump-ejector system.
- 30 December 2022
- Published by Oil Gas Scientific Research Project Institute in SOCAR Proceedings
- No. SI2,p. 28-36
Application of simultaneous water and gas injection technology for exhaust gas utilization and reduction of CO2 emissions
In today's world, the energy sector has a major impact on the climate. In this process, the share attributable to oil and gas producers is large. The paper shows the prospects of reducing flaring of associated petroleum gas and carbon dioxide emissions by utilization of exhaust (flue) gases for injection into the reservoir to enhance oil recovery. The main industrial sources of exhaust (flue) gases are given. The scope of research on the use of exhaust gases in the development of oil fields with different properties is analyzed. The technology of simultaneous water and gas injection, aimed at the utilization of exhaust gases and increase oil recovery fields, is proposed. The technology of simultaneous water and gas injection is implemented with the use of pump-ejector systems and allows for the simultaneous injection of water and gas into productive formations. The main parameters of pumpejector system are determined for the conditions of a particular field. Keywords: exhaust (fuel) gases utilization; enhanced oil recovery (EOR); SWAG injection; pump-ejector system.
- 22 December 2022
- Published by Ore and Metals Publishing House in Eurasian Mining
- No. 2,p. 3-6
Importance of accounting macro heterogeneity of productive strata to improve efficiency of water alternating gas injection process
The paper focuses on improvement of reliability of geological information used in the water alternating gas injection projects for productive strata in the course of scavenger oilfield development. Spotlight is on the study of macro heterogeneities revealed by interpretation of drilling and seismic survey data. One of the critical objectives of this research is updating of interwell correlation according to the analysis of seismic wavefield recorded in the interval of productive strata occurrence. The paper describes a casestudy of the revised concept on the structure of BV10 stratum in the Nizhnevartovsk oil and gas area of the West Siberian oil and gas province. As a result, instead of the current concept on the parallel bedding of the test sedimentation, the progradation structure of the latter is assumed, which eliminates the use of wouldbe lithological screens in delineation of oil reservoirs. The disregard of the progradation structure in oilfield development would have an adverse influence on the oil recovery efficiency. The integrated interpretation of drilling and seismic survey data reveals screening fractures which make an impact on oil displacement efficiency. It is necessary to take such fractures into account in water alternating gas injection. Inclusion of sufficient vertical discriminability of well information and lateral discriminability of seismic survey data in the analysis allows predicting the change in petrophysical parameters in interwell space. The authors exemplify interpolation of well data with regard to wavefield properties. The information on macro heterogeneities of reservoir properties helps improve the water alternating gas injection performance and, accordingly, enhance the sweep efficiency. The paper presents also the physical framework for the adjustment of fluid flow in reservoirs using the seismic survey data. This paper has been supported by the RUDN University’s Strategic Academic Leadership Program.
- 22 December 2022
- Published by Ore and Metals Publishing House in Eurasian Mining
- No. 2,p. 3-6
Importance of accounting macro heterogeneity of productive strata to improve efficiency of water alternating gas injection process
The paper focuses on improvement of reliability of geological information used in the water alternating gas injection projects for productive strata in the course of scavenger oilfield development. Spotlight is on the study of macro heterogeneities revealed by interpretation of drilling and seismic survey data. One of the critical objectives of this research is updating of interwell correlation according to the analysis of seismic wavefield recorded in the interval of productive strata occurrence. The paper describes a casestudy of the revised concept on the structure of BV10 stratum in the Nizhnevartovsk oil and gas area of the West Siberian oil and gas province. As a result, instead of the current concept on the parallel bedding of the test sedimentation, the progradation structure of the latter is assumed, which eliminates the use of wouldbe lithological screens in delineation of oil reservoirs. The disregard of the progradation structure in oilfield development would have an adverse influence on the oil recovery efficiency. The integrated interpretation of drilling and seismic survey data reveals screening fractures which make an impact on oil displacement efficiency. It is necessary to take such fractures into account in water alternating gas injection. Inclusion of sufficient vertical discriminability of well information and lateral discriminability of seismic survey data in the analysis allows predicting the change in petrophysical parameters in interwell space. The authors exemplify interpolation of well data with regard to wavefield properties. The information on macro heterogeneities of reservoir properties helps improve the water alternating gas injection performance and, accordingly, enhance the sweep efficiency. The paper presents also the physical framework for the adjustment of fluid flow in reservoirs using the seismic survey data. This paper has been supported by the RUDN University’s Strategic Academic Leadership Program.
- Open Access
The Rod String Loads Variation during Short-Term Annular Gas Extraction
This paper highlights field studies to determine the nature of variations in the load on the sucker-rod string during short-term gas extraction from the wellbore annulus. The results of step-by-step gas extraction from the annular spaces of the wells of fields developed by PJSC TATNEFT are provided. In the course of investigations, we have obtained both the trends of maximum and minimum loads on the polished rod during annular gas extraction, and the dependence of maximum load increment on the rod string with respect to pump size and pressure variation in the annular space. The analysis of the research data resulted in the elaboration of guidelines for short-term extraction of annular gas from wells operated by the PCP units.
Open AccessThe Rod String Loads Variation during Short-Term Annular Gas Extraction
This paper highlights field studies to determine the nature of variations in the load on the sucker-rod string during short-term gas extraction from the wellbore annulus. The results of step-by-step gas extraction from the annular spaces of the wells of fields developed by PJSC TATNEFT are provided. In the course of investigations, we have obtained both the trends of maximum and minimum loads on the polished rod during annular gas extraction, and the dependence of maximum load increment on the rod string with respect to pump size and pressure variation in the annular space. The analysis of the research data resulted in the elaboration of guidelines for short-term extraction of annular gas from wells operated by the PCP units.
- Open Access
Improving the Efficiency of Curved Wells’ Operation by Means of Progressive Cavity Pumps
This paper proposes a solution to the problem of improving the reliability of the operation of progressive cavity pump units in deviated and directional wells. High dogleg severity significantly contributes to rod breakage; rods often break close to the “elbows” with a dogleg severity of 2 deg/10 m or higher. Statistical analyses were used to identify the frequency of failures and their impact on the reliability of a PCP unit. The design layout and mathematical model for pump rods’ torsional vibrations in the curved section of a wellbore were developed. A simulation of the curved section was performed. This article provides the basic formulas needed to design a rotating rod string using two reduced discs. The creation of an additional crooked section resulted in multiple reductions in the “resonant” rotational speed and rigidity in the mathematical model. Determining the moment of inertia of the reduced discs’ mass made it possible to determine the sucker-rod string’s stiffness, the circular rotation frequency, and the number of sucker-rod revolutions under resonance. The number of reduced discs on the sucker-rod string depends on the curvature pattern. In summary, a centralizer for a rotating string was designed to reduce the vibration and shock effects of rods on the tubing.
Open AccessImproving the Efficiency of Curved Wells’ Operation by Means of Progressive Cavity Pumps
This paper proposes a solution to the problem of improving the reliability of the operation of progressive cavity pump units in deviated and directional wells. High dogleg severity significantly contributes to rod breakage; rods often break close to the “elbows” with a dogleg severity of 2 deg/10 m or higher. Statistical analyses were used to identify the frequency of failures and their impact on the reliability of a PCP unit. The design layout and mathematical model for pump rods’ torsional vibrations in the curved section of a wellbore were developed. A simulation of the curved section was performed. This article provides the basic formulas needed to design a rotating rod string using two reduced discs. The creation of an additional crooked section resulted in multiple reductions in the “resonant” rotational speed and rigidity in the mathematical model. Determining the moment of inertia of the reduced discs’ mass made it possible to determine the sucker-rod string’s stiffness, the circular rotation frequency, and the number of sucker-rod revolutions under resonance. The number of reduced discs on the sucker-rod string depends on the curvature pattern. In summary, a centralizer for a rotating string was designed to reduce the vibration and shock effects of rods on the tubing.
- Open Access
- 1 March 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 666 (6) , 062014
Influence of Produced Fluid Parameters on the Use of Separator as a Component of an Electric Plunger Pump Unit
The article discusses the use of separators of mechanical impurities in linear electric plunger submersible pumps units in oil wells. The advantages of these units and their area of application are highlighted. The diagram and description of the bench for conducting researches on the study of submersible unit assembly of the electric plunger pump together with a separator of gas and mechanical impurities are shown. Formulas and results of calculating the settling rate of particles of different diameters are presented. The main dependences of the change in the settling rate of particles depending on the viscosity of the liquid have been determined.
- 1 March 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 666 (6) , 062014
Open AccessInfluence of Produced Fluid Parameters on the Use of Separator as a Component of an Electric Plunger Pump Unit
The article discusses the use of separators of mechanical impurities in linear electric plunger submersible pumps units in oil wells. The advantages of these units and their area of application are highlighted. The diagram and description of the bench for conducting researches on the study of submersible unit assembly of the electric plunger pump together with a separator of gas and mechanical impurities are shown. Formulas and results of calculating the settling rate of particles of different diameters are presented. The main dependences of the change in the settling rate of particles depending on the viscosity of the liquid have been determined.
- Open Access
- 1 February 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 678 (1) , 012039
Perspectives of application of simultaneous water and gas injection for utilizing associated petroleum gas and enhancing oil recovery in the Arctic fields
At present, it is becoming more relevant to use other displacing agents, which are more effective in comparison with waterflooding, for increasing oil and gas condensate deposits component recovery. One of such promising methods is simultaneous water and gas injection. In this article, we present the principal options for using simultaneous water and gas injection in Arctic fields, case study of the Urengoyskoye and Prirazlomnoye fields. Technological schemes for its implementation in the Urengoyskoye field at low reservoir pressures are considered. Filtration studies of oil from reservoir models with water-gas mixtures at various gas contents allow increasing hydrocarbon recovery efficiency by determining the area of rational gas contents. For the conditions of the Prirazlomnoye field, the possibility of using pump-ejector system for the utilization of associated petroleum gas has been established.
- 1 February 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 678 (1) , 012039
Open AccessPerspectives of application of simultaneous water and gas injection for utilizing associated petroleum gas and enhancing oil recovery in the Arctic fields
At present, it is becoming more relevant to use other displacing agents, which are more effective in comparison with waterflooding, for increasing oil and gas condensate deposits component recovery. One of such promising methods is simultaneous water and gas injection. In this article, we present the principal options for using simultaneous water and gas injection in Arctic fields, case study of the Urengoyskoye and Prirazlomnoye fields. Technological schemes for its implementation in the Urengoyskoye field at low reservoir pressures are considered. Filtration studies of oil from reservoir models with water-gas mixtures at various gas contents allow increasing hydrocarbon recovery efficiency by determining the area of rational gas contents. For the conditions of the Prirazlomnoye field, the possibility of using pump-ejector system for the utilization of associated petroleum gas has been established.
- Open Access
- 15 December 2019
- Published by Peoples' Friendship University of Russia in RUDN Journal of Engineering Researches
- Vol. 20 (3) , 254-260
Increasing efficiency of work of a liquid-gas ejector
The proposed solution relates to fluidics and can be used, for example, in the extraction of oil and gas, the collection and preparation of oil, gas and water, the extraction of methane from methane beds, oil refining. The technical result is to increase the efficiency of a liquid-gas ejector by ensuring its work in the field of rational concentrations and salt composition, in which the intensification of energy exchange between the working fluid and the ejected gas is achieved. The essence of the proposed solution: the method of operation of a liquid-gas ejector involves injecting a working fluid with a power pump into the ejector nozzle, pumping gas with an ejector, creating, dispersing and increasing the pressure of a gas-liquid mixture with an ejector using aqueous solutions of salts as a working fluid. The values of the concentration and composition of salts in the working fluid are maintained within the range of rational concentrations and composition of salts, in which increased values of the efficiency of the ejector are achieved. Salts are added to the weakly mineralized aqueous solutions, and the highly mineralized aqueous solutions are diluted with fresh water. As the working fluid, the formation and/or incidentally produced waters of oil, gas, gas condensate and methane-coal deposits, which are aqueous solutions of salts, are used if the composition and concentration of salts in the produced and/or incidentally produced waters are within the range of rational concentrations and composition of salts in which provides an increase in the efficiency of the ejector. The boundaries of the field of rational concentrations and salt composition are preliminarily determined by laboratory bench studies.
- 15 December 2019
- Published by Peoples' Friendship University of Russia in RUDN Journal of Engineering Researches
- Vol. 20 (3) , 254-260
Open AccessIncreasing efficiency of work of a liquid-gas ejector
The proposed solution relates to fluidics and can be used, for example, in the extraction of oil and gas, the collection and preparation of oil, gas and water, the extraction of methane from methane beds, oil refining. The technical result is to increase the efficiency of a liquid-gas ejector by ensuring its work in the field of rational concentrations and salt composition, in which the intensification of energy exchange between the working fluid and the ejected gas is achieved. The essence of the proposed solution: the method of operation of a liquid-gas ejector involves injecting a working fluid with a power pump into the ejector nozzle, pumping gas with an ejector, creating, dispersing and increasing the pressure of a gas-liquid mixture with an ejector using aqueous solutions of salts as a working fluid. The values of the concentration and composition of salts in the working fluid are maintained within the range of rational concentrations and composition of salts, in which increased values of the efficiency of the ejector are achieved. Salts are added to the weakly mineralized aqueous solutions, and the highly mineralized aqueous solutions are diluted with fresh water. As the working fluid, the formation and/or incidentally produced waters of oil, gas, gas condensate and methane-coal deposits, which are aqueous solutions of salts, are used if the composition and concentration of salts in the produced and/or incidentally produced waters are within the range of rational concentrations and composition of salts in which provides an increase in the efficiency of the ejector. The boundaries of the field of rational concentrations and salt composition are preliminarily determined by laboratory bench studies.
- Open Access
- 26 August 2019
- Published by Saint-Petersburg Mining University in Journal of Mining Institute
- Vol. 238 (4) , 415-422
Improving the Operation of Pump-ejector Systems at Varying Flow Rates of Associated Petroleum Gas
Совершенствование эксплуатации насосно-эжекторных систем при изменяющихся расходах попутного нефтяного газа
- 26 August 2019
- Published by Saint-Petersburg Mining University in Journal of Mining Institute
- Vol. 238 (4) , 415-422
Open AccessImproving the Operation of Pump-ejector Systems at Varying Flow Rates of Associated Petroleum Gas
Совершенствование эксплуатации насосно-эжекторных систем при изменяющихся расходах попутного нефтяного газа