Salmie Suhana Che Abdullah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Salmie Suhana Che Abdullah has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- Siti Hawa Salleh
Universiti Malaysia Perlis (UniMAP), Faculty of Chemical Engineering & Technology, Taman Muhibbah, 02600 Jejawi, Perlis, Malaysia; Center of Excellent Geopolymer and Green Technology, Taman Muhibbah, 02600 Jejawi, Perlis, Malaysia
5 shared publications Imaduddin Helmi Wan Nordin
University Malaysia Perlis (UniMAP)
3 shared publicationsRohaya Abdul Malek
Universiti Malaysia Perlis (UniMAP)
3 shared publicationsSiti Hawa Salleh
Universiti Malaysia Perlis (UniMAP)
3 shared publications- Akira Kishimoto
Okayama University
2 shared publications - Hidetaka Hayashi
Department of Diagnostic Radiology, Faculty of Life Sciences, Kumamoto University, 1-1-1 Honjo, Chuo-ku, Kumamoto, 860-8556, Japan
2 shared publications
Latest Publications
- Open Access
- 22 June 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 71 (2) , 473-480
Thermal Resilience of Eco-Binary Mortar: an Experimental Study of High-Temperature Exposure
Mortar exposed to high temperatures can experience significant degradation in strength and durability. One potential solution is replacing cement with alternative pozzolanic materials, such as Rice Husk Ash (RHA), which has a high silica content when processed under controlled burning conditions. This study investigates the use of RHA as a partial replacement in mortar, with additions ranging from 5 to 20 wt.%. As the amount of RHA increased, the mortar color darkened to a grayish shade. Surprisingly, the inclusion of 5 wt.% RHA resulted in almost double the compressive strength compared to conventional mortar, while 10 and 15 wt.% additions also showed improved performance. However, the addition of 20 wt.% RHA led to a decrease in compressive strength to 12.49 MPa, below that of standard mortar. High-temperature exposure (up to 1,093°C) affected the moisture content of the cement paste, changing its appearance to a whitish-gray color and impacting its mechanical properties. The relative strength values for all samples ranged between 0.35 and 0.16. Thermal analysis showed that free water evaporated between 82 to 140°C, followed by the decomposition of Ca(OH)2 at 445 to 454°C. The results suggest that 5 wt.% RHA provides optimal properties compared to other mixtures. This study highlights that RHA, as a low-cost agricultural waste, can be effectively utilized in the mortar industry, offering an environmentally friendly solution to both waste disposal and sustainability issues.
- 22 June 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 71 (2) , 473-480
Open AccessThermal Resilience of Eco-Binary Mortar: an Experimental Study of High-Temperature Exposure
Mortar exposed to high temperatures can experience significant degradation in strength and durability. One potential solution is replacing cement with alternative pozzolanic materials, such as Rice Husk Ash (RHA), which has a high silica content when processed under controlled burning conditions. This study investigates the use of RHA as a partial replacement in mortar, with additions ranging from 5 to 20 wt.%. As the amount of RHA increased, the mortar color darkened to a grayish shade. Surprisingly, the inclusion of 5 wt.% RHA resulted in almost double the compressive strength compared to conventional mortar, while 10 and 15 wt.% additions also showed improved performance. However, the addition of 20 wt.% RHA led to a decrease in compressive strength to 12.49 MPa, below that of standard mortar. High-temperature exposure (up to 1,093°C) affected the moisture content of the cement paste, changing its appearance to a whitish-gray color and impacting its mechanical properties. The relative strength values for all samples ranged between 0.35 and 0.16. Thermal analysis showed that free water evaporated between 82 to 140°C, followed by the decomposition of Ca(OH)2 at 445 to 454°C. The results suggest that 5 wt.% RHA provides optimal properties compared to other mixtures. This study highlights that RHA, as a low-cost agricultural waste, can be effectively utilized in the mortar industry, offering an environmentally friendly solution to both waste disposal and sustainability issues.
- 22 December 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- p. 1653
Enhancing Samarium-Doped Ceria Electrolytes with Manganese for Solid Oxide Fuel Cell
This study focuses on synthesizing new electrolyte materials for solid oxide fuel cell (SOFC) with the composition of Ce0.8-x MnxSm0.2O1.9-δ (x = 0, 0.025, 0.05, 0.1). The main aim is to investigate the effect of varying molar concentrations of manganese (Mn) as a secondary dopant on density, phase composition, and ionic conductivity of samarium-doped ceria (SDC). Accordingly, X-ray diffraction (XRD) and impedance spectroscopy (IS) were employed to characterize the samples. Mn-doped samples sintered at 1400°C for 5 hours exhibited a single-phase cubic fluorite structure with larger lattice parameters and volumes compared to the undoped sample. All samples achieved a high relative density exceeding 94%. Notably, the sample with 10 mol% Mn reached a relative density of 99.6%. Impedance data revealed that the ionic conductivity of the Mn-doped samples was enhanced by an order of magnitude compared to the undoped samples. This indicates that Mn is a promising dopant for SDC in electrolyte applications for SOFCs.
- 22 December 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- p. 1653
Enhancing Samarium-Doped Ceria Electrolytes with Manganese for Solid Oxide Fuel Cell
This study focuses on synthesizing new electrolyte materials for solid oxide fuel cell (SOFC) with the composition of Ce0.8-x MnxSm0.2O1.9-δ (x = 0, 0.025, 0.05, 0.1). The main aim is to investigate the effect of varying molar concentrations of manganese (Mn) as a secondary dopant on density, phase composition, and ionic conductivity of samarium-doped ceria (SDC). Accordingly, X-ray diffraction (XRD) and impedance spectroscopy (IS) were employed to characterize the samples. Mn-doped samples sintered at 1400°C for 5 hours exhibited a single-phase cubic fluorite structure with larger lattice parameters and volumes compared to the undoped sample. All samples achieved a high relative density exceeding 94%. Notably, the sample with 10 mol% Mn reached a relative density of 99.6%. Impedance data revealed that the ionic conductivity of the Mn-doped samples was enhanced by an order of magnitude compared to the undoped samples. This indicates that Mn is a promising dopant for SDC in electrolyte applications for SOFCs.
- 8 December 2022
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1076, 73-81
Electrochemical Study of Al2O3/ Industrial Waste Coating on Mg Substrate via Sol-Gel Method
Industrial waste is primarily handled using landfills in both developed and developing countries. While there has been a significant rise in solid waste reduction, reuse, and recycling, landfill disposal will inevitably remain the most commonly used form of waste management. Although landfilling provides an economic means of waste disposal, it can lead to environmental degradation by releasing various contaminants if not managed properly. In this work, industrial waste from electrostatic precipitators (ESP) will be beneficial for the production of coatings on metal substrates. The sol-gel coating method have been attempted for deposition on pure Mg samples. Using the potentiodynamic polarization (PDP) method and hydrogen evolution analysis, the effectiveness of the coating, which is the corrosion resistance was analyzed. A minimal application of Tetraethyl orthosilicate (TEOS) in the ESP dust solution has been shown to substantially reduce the corrosion rate of Mg. This is likely due to the impact of its concentrations through the sol-gel process that could increase the size of the particle shape or growth.
- 8 December 2022
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1076, 73-81
Electrochemical Study of Al2O3/ Industrial Waste Coating on Mg Substrate via Sol-Gel Method
Industrial waste is primarily handled using landfills in both developed and developing countries. While there has been a significant rise in solid waste reduction, reuse, and recycling, landfill disposal will inevitably remain the most commonly used form of waste management. Although landfilling provides an economic means of waste disposal, it can lead to environmental degradation by releasing various contaminants if not managed properly. In this work, industrial waste from electrostatic precipitators (ESP) will be beneficial for the production of coatings on metal substrates. The sol-gel coating method have been attempted for deposition on pure Mg samples. Using the potentiodynamic polarization (PDP) method and hydrogen evolution analysis, the effectiveness of the coating, which is the corrosion resistance was analyzed. A minimal application of Tetraethyl orthosilicate (TEOS) in the ESP dust solution has been shown to substantially reduce the corrosion rate of Mg. This is likely due to the impact of its concentrations through the sol-gel process that could increase the size of the particle shape or growth.
- 31 August 2022
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 930, 179-186
Assessment on Optimal Level of Reactive Biosilica Affected by Incineration Conditions in Perlis Rice Husk Ash as Supplementary Cementitious Materials in Concrete
Rice husk (RH) is an agricultural waste transformed to produce secondary by-products and is widely accepted as a substitution of cement or concrete mixtures. This paper deals with the optimal level of SiO2 content due to various incineration conditions of rice husk grown in Perlis, Malaysia. RH was burnt in a controlled environment with a targeted temperature of 650, 750 and 850 °C at various incineration period between 1 and 6 h. All the ashes were assessed for visual inspection and physiochemical and mineralogical properties using X-ray fluorescence (XRF) and X-ray diffraction (XRD). From the analysis, a significant amount of SiO2 in the range of 89–93 wt % was successfully obtained with the preferable properties of supplementary cementitious materials: amorphous silica with high reactivity, ultrafine size, and large surface area. Contrary, the burning temperature of 850 °C greater than 4 h incineration period is not advisable to be used as it transformed into a crystalline phase. No obvious color changes were observed for the ashes as the amount oxide compound of K2O causes carbon entrapped in surface melting. To sum up, 650 °C incineration for 1 h shows an optimum result, and the RH is bearable to reduce the negative impact on the environment.
- 31 August 2022
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 930, 179-186
Assessment on Optimal Level of Reactive Biosilica Affected by Incineration Conditions in Perlis Rice Husk Ash as Supplementary Cementitious Materials in Concrete
Rice husk (RH) is an agricultural waste transformed to produce secondary by-products and is widely accepted as a substitution of cement or concrete mixtures. This paper deals with the optimal level of SiO2 content due to various incineration conditions of rice husk grown in Perlis, Malaysia. RH was burnt in a controlled environment with a targeted temperature of 650, 750 and 850 °C at various incineration period between 1 and 6 h. All the ashes were assessed for visual inspection and physiochemical and mineralogical properties using X-ray fluorescence (XRF) and X-ray diffraction (XRD). From the analysis, a significant amount of SiO2 in the range of 89–93 wt % was successfully obtained with the preferable properties of supplementary cementitious materials: amorphous silica with high reactivity, ultrafine size, and large surface area. Contrary, the burning temperature of 850 °C greater than 4 h incineration period is not advisable to be used as it transformed into a crystalline phase. No obvious color changes were observed for the ashes as the amount oxide compound of K2O causes carbon entrapped in surface melting. To sum up, 650 °C incineration for 1 h shows an optimum result, and the RH is bearable to reduce the negative impact on the environment.
- 31 August 2022
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 930, 9-14
Synthesis and Characterization of Sm/Zr Co-Doped CeO2 Ceramic for Solid Electrolyte Application
In this paper, we report the properties of Sm and Zr co-doped CeO2 ceramic, which synthesized by conventional solid state reaction. Sm content in Ce site was fixed at 20 mol%, meanwhile Zr was varied in the range of 5 to 15 mol%. All samples was pressed under 26 MPa before sintered at 1400 °C for 5 hours. The X-ray diffraction patterns of samples confirm all the samples are in single-phase with cubic fluorite structure. The lattice parameter decreases with increase in Zr concentration. The relative density of all samples was more that 95%. The microhardness achieved highest value for sample with 0.05 mol% of Zr. The shrinkage and the change of bulk density shows direct correlation.
- 31 August 2022
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 930, 9-14
Synthesis and Characterization of Sm/Zr Co-Doped CeO2 Ceramic for Solid Electrolyte Application
In this paper, we report the properties of Sm and Zr co-doped CeO2 ceramic, which synthesized by conventional solid state reaction. Sm content in Ce site was fixed at 20 mol%, meanwhile Zr was varied in the range of 5 to 15 mol%. All samples was pressed under 26 MPa before sintered at 1400 °C for 5 hours. The X-ray diffraction patterns of samples confirm all the samples are in single-phase with cubic fluorite structure. The lattice parameter decreases with increase in Zr concentration. The relative density of all samples was more that 95%. The microhardness achieved highest value for sample with 0.05 mol% of Zr. The shrinkage and the change of bulk density shows direct correlation.
- 3 May 2021
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2339 (1) , 020238
The hydrogen evolution of pure magnesium in different electrolytes
The hydrogen gas evolution from the corroding magnesium (Mg) arises not only from the bare Mg surface but also from the Mg(OH)2 oxide layer as well. In fact, the presence of Mg(OH)2 oxide layer also doubled the rate of hydrogen gas evolution. In this work, a conventional hydrogen gas collection using volumetric method has been applied to observe the effect of sodium chloride (NaCl) on hydrogen evolution of Mg. Cathodic polarization and scanning electron microscopic (SEM) tests had been done in the same solution to confirm the observations. These observations demonstrate that, even though the initial surface of Mg had been fully covered by Mg(OH)2 oxide layer, the abundant hydrogen gas still can be released from the corroded surface. In addition, the double increases of hydrogen evolution rate (HER) during free corrosion in 7.0% NaCl can be seen as compared to distilled water.
- 3 May 2021
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2339 (1) , 020238
The hydrogen evolution of pure magnesium in different electrolytes
The hydrogen gas evolution from the corroding magnesium (Mg) arises not only from the bare Mg surface but also from the Mg(OH)2 oxide layer as well. In fact, the presence of Mg(OH)2 oxide layer also doubled the rate of hydrogen gas evolution. In this work, a conventional hydrogen gas collection using volumetric method has been applied to observe the effect of sodium chloride (NaCl) on hydrogen evolution of Mg. Cathodic polarization and scanning electron microscopic (SEM) tests had been done in the same solution to confirm the observations. These observations demonstrate that, even though the initial surface of Mg had been fully covered by Mg(OH)2 oxide layer, the abundant hydrogen gas still can be released from the corroded surface. In addition, the double increases of hydrogen evolution rate (HER) during free corrosion in 7.0% NaCl can be seen as compared to distilled water.
- 17 September 2020
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1010, 280-285
Effect of H2/N2 Mixtures on Reduction of Nickel Oxide
This paper describes the reduction of nickel oxide under different gas mixture. The influence of gas mixture on phase, density, morphology and pore size of reduced nickel oxide were studied. Nickel oxide pellets sintered at 1400 °C were reduced under various hydrogen-nitrogen gas mixtures, namely 40% H2-60% N2, 60% H2-40% N2, 80% H2-20% N2. Phase identification, density measurement and observation of morphology were conducted on samples before and after reduction process. Under all gas mixtures, nickel oxide was completely reduced to nickel. Density of the samples decreased in the range of 21% to 32% depends on H2 percentage used. Results from the density shows that the higher the H2 gas concentration, the smaller the density changes. Significant change in porosity of the sample before and after reduction was observed. Size of pore after reduction determined by H2 concentration used during reduction where the higher the H2 concentration resulted in large pore size.
- 17 September 2020
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1010, 280-285
Effect of H2/N2 Mixtures on Reduction of Nickel Oxide
This paper describes the reduction of nickel oxide under different gas mixture. The influence of gas mixture on phase, density, morphology and pore size of reduced nickel oxide were studied. Nickel oxide pellets sintered at 1400 °C were reduced under various hydrogen-nitrogen gas mixtures, namely 40% H2-60% N2, 60% H2-40% N2, 80% H2-20% N2. Phase identification, density measurement and observation of morphology were conducted on samples before and after reduction process. Under all gas mixtures, nickel oxide was completely reduced to nickel. Density of the samples decreased in the range of 21% to 32% depends on H2 percentage used. Results from the density shows that the higher the H2 gas concentration, the smaller the density changes. Significant change in porosity of the sample before and after reduction was observed. Size of pore after reduction determined by H2 concentration used during reduction where the higher the H2 concentration resulted in large pore size.
- Open Access
- 1 December 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 701 (1) , 012028
Influence of NiO to SDC ratio on the properties of Ni-SDC cermet prepared via reduction process
This works presents the preparation of Ni-Ce0.8Sm0.2O1.9 (Ni-SDC) ceramic-metal from reduction of NiO-Ce0.8Sm0.2O1.9 (NiO-SDC) ceramics for application of solid oxide fuel cell. NiO-SDC powder with different weight percentage of NiO and SDC (100% NiO + 0% SDC), (80% NiO + 20% SDC), (70% NiO + 30% SDC) and (60% NiO + 40% SDC) was pelletized and sintered at 1400 °C for 4 hours. Then, pellet samples were undergone reduction process using mixed gas of hydrogen and nitrogen gas with concentration of 40% H2 and 60% N2 at 800 °C for 2 h. Phase analysis was done using X-ray Diffraction and it was found that for all samples, NiO was completely reduced to Ni, meanwhile SDC was remained in its phase. The density of the samples decreased after reduction, results in more porous samples were obtained. It was found that increasing NiO content lead to sample with higher porosity. The surface morphology of the samples was observed by using the Scanning Electron Microscopy.
- 1 December 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 701 (1) , 012028
Open AccessInfluence of NiO to SDC ratio on the properties of Ni-SDC cermet prepared via reduction process
This works presents the preparation of Ni-Ce0.8Sm0.2O1.9 (Ni-SDC) ceramic-metal from reduction of NiO-Ce0.8Sm0.2O1.9 (NiO-SDC) ceramics for application of solid oxide fuel cell. NiO-SDC powder with different weight percentage of NiO and SDC (100% NiO + 0% SDC), (80% NiO + 20% SDC), (70% NiO + 30% SDC) and (60% NiO + 40% SDC) was pelletized and sintered at 1400 °C for 4 hours. Then, pellet samples were undergone reduction process using mixed gas of hydrogen and nitrogen gas with concentration of 40% H2 and 60% N2 at 800 °C for 2 h. Phase analysis was done using X-ray Diffraction and it was found that for all samples, NiO was completely reduced to Ni, meanwhile SDC was remained in its phase. The density of the samples decreased after reduction, results in more porous samples were obtained. It was found that increasing NiO content lead to sample with higher porosity. The surface morphology of the samples was observed by using the Scanning Electron Microscopy.
- 1 January 2018
- Published by Elsevier in Journal of Power Sources
- Vol. 374, 92-96
Millimeter-wave irradiation heating for operation of doped CeO2 electrolyte-supported single solid oxide fuel cell
- 1 January 2018
- Published by Elsevier in Journal of Power Sources
- Vol. 374, 92-96
Millimeter-wave irradiation heating for operation of doped CeO2 electrolyte-supported single solid oxide fuel cell
- 1 February 2017
- Published by Elsevier in Materials & Design
- Vol. 115, 231-237
Enhanced electrical conductivity of doped CeO2 under millimeter-wave irradiation heating
- 1 February 2017
- Published by Elsevier in Materials & Design
- Vol. 115, 231-237
Enhanced electrical conductivity of doped CeO2 under millimeter-wave irradiation heating