Ralf Glienke
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ralf Glienke has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Maik Dörre
Mechanische Verbindungstechnik, Fraunhofer-Institut für Großstrukturen in der Produktionstechnik IGP, Rostock, Deutschland
7 shared publications - Mathias Schwarz
Fraunhofer‐Institut für Großstrukturen in der Produktionstechnik IGP Albert‐Einstein‐Str. 30 18059 Rostock
7 shared publications - Knuth‐Michael Henkel
Chair of Joining Technology, University of Rostock, 18059 Rostock, Germany
5 shared publications - Christoph Blunk
Fraunhofer Institute for Large Structures in Production Engineering IGP Albert‐Einstein‐Str. 30 18059 Rostock Germany
4 shared publications - Daniela Schwerdt
Hochschule Wismar University of Business, Technology and Design Fakultät für Ingenieurwissenschaften Bereich Maschinenbau/Verfahrens‐ und Umwelttechnik Philipp‐Müller‐Straße 14 23966 Wismar
3 shared publications - Florian Kalkowsky
Fraunhofer Institute for Large Structures in Production Engineering IGP
3 shared publications
Latest Publications
- Open Access
- 19 December 2025
- Published by MDPI AG in Engineering Proceedings
- Vol. 119 (1) , 31
Determination of Fatigue Crack Size in High-Strength Bolting Assemblies Using Hydrogen-Induced Cracking
For the validation of approaches like fracture mechanics used for the description of crack propagation in high-strength bolting assemblies, it is often necessary to determine the size of an existing crack in the tested assembly. However, since the fatigue crack typically initiates in the root of the first load bearing thread, it is not directly accessible during fatigue testing. The crack size determination method presented here achieves further propagation of the original fatigue crack after the fatigue test by hydrogen-induced cracking under constant load. The characteristic microstructure of the resulting fracture surface then allows for the determination of the original crack size. In the present study, the fatigue crack sizes in M12 bolting assemblies are determined and a corresponding linear elastic fracture mechanics model is validated. The presented method reliably leads to a failure in the plane of the original fatigue crack and allows for a precise measurement of the crack length. The validated fracture mechanics model describes the crack propagation reasonably well, taking into account the overall service life. Overall, the presented method is a valuable addition to existing crack size determination methods and a versatile tool in the further development of more advanced fracture mechanics models for high-strength bolting assemblies.
- 19 December 2025
- Published by MDPI AG in Engineering Proceedings
- Vol. 119 (1) , 31
Open AccessDetermination of Fatigue Crack Size in High-Strength Bolting Assemblies Using Hydrogen-Induced Cracking
For the validation of approaches like fracture mechanics used for the description of crack propagation in high-strength bolting assemblies, it is often necessary to determine the size of an existing crack in the tested assembly. However, since the fatigue crack typically initiates in the root of the first load bearing thread, it is not directly accessible during fatigue testing. The crack size determination method presented here achieves further propagation of the original fatigue crack after the fatigue test by hydrogen-induced cracking under constant load. The characteristic microstructure of the resulting fracture surface then allows for the determination of the original crack size. In the present study, the fatigue crack sizes in M12 bolting assemblies are determined and a corresponding linear elastic fracture mechanics model is validated. The presented method reliably leads to a failure in the plane of the original fatigue crack and allows for a precise measurement of the crack length. The validated fracture mechanics model describes the crack propagation reasonably well, taking into account the overall service life. Overall, the presented method is a valuable addition to existing crack size determination methods and a versatile tool in the further development of more advanced fracture mechanics models for high-strength bolting assemblies.
- 10 August 2025
- Published by Springer Nature
- p. 67-90
Extending the Service Life of Orthotropic Steel Decks in Existing Structures by Using Cold Joining Technique
- 10 August 2025
- Published by Springer Nature
- p. 67-90
Extending the Service Life of Orthotropic Steel Decks in Existing Structures by Using Cold Joining Technique
- Open Access
- 29 February 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (5) , 1143-1168
Evaluation of the fatigue resistance of butt-welded joints in towers of wind turbines — a comparison of experimental studies with small scale and component tests as well as numerical based approaches with local concepts
Wind turbines must endure a high number of load cycles during their service lifetime. Therefore, the fatigue strength verification plays an important role. Butt-welded joints are one of the most common structural details in the tower structure of wind turbines. In general, the nominal stress method is used for their fatigue verification. The Eurocode 3 part 1–9 is the current design standard for this field of application and defines the fatigue resistance by pre-defined FAT-classes. This paper presents recent results of fatigue tests on small-scaled specimens and large components with transverse butt welds to discuss the validity of the FAT-class. In addition, results from numerical simulations for the verification with the effective notch stress and the crack propagation approach are used for comparison. For this purpose, macroscopic measurements of the weld seam geometry and a 3D scan were used for a realistic consideration of the notch effect in the simulation. Based on the consistency between the numerical results and the fatigue tests, the influence of the seam geometry on the fatigue resistance was worked out. Furthermore, a prediction of the fatigue strength of butt-welded joints with plate thicknesses up to 80 mm was carried out.
- 29 February 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (5) , 1143-1168
Open AccessEvaluation of the fatigue resistance of butt-welded joints in towers of wind turbines — a comparison of experimental studies with small scale and component tests as well as numerical based approaches with local concepts
Wind turbines must endure a high number of load cycles during their service lifetime. Therefore, the fatigue strength verification plays an important role. Butt-welded joints are one of the most common structural details in the tower structure of wind turbines. In general, the nominal stress method is used for their fatigue verification. The Eurocode 3 part 1–9 is the current design standard for this field of application and defines the fatigue resistance by pre-defined FAT-classes. This paper presents recent results of fatigue tests on small-scaled specimens and large components with transverse butt welds to discuss the validity of the FAT-class. In addition, results from numerical simulations for the verification with the effective notch stress and the crack propagation approach are used for comparison. For this purpose, macroscopic measurements of the weld seam geometry and a 3D scan were used for a realistic consideration of the notch effect in the simulation. Based on the consistency between the numerical results and the fatigue tests, the influence of the seam geometry on the fatigue resistance was worked out. Furthermore, a prediction of the fatigue strength of butt-welded joints with plate thicknesses up to 80 mm was carried out.
Aktuelle Erkenntnisse zum Einsatz von Klebstoff in vorgespannten Schraubenverbindungen unter Berücksichtigung von Fertigungseinflüssen
Nicht vorwiegend ruhend beanspruchte Konstruktionen werden im Stahlbau i. Allg. mit gleitfest vorgespannten Verbindungen ausgeführt, da diese aufgrund ihrer reibschlüssigen Kraftübertragung einen hohen Ermüdungswiderstand aufweisen. Die übertragbaren Kräfte in Schraubenverbindungen unter Scherbeanspruchung sind jedoch begrenzt. Wird zusätzlich Klebstoff auf die Reibflächen appliziert, entsteht die sog. vorgespannte Hybridverbindung. Die damit verbundene Traglaststeigerung unter Berücksichtigung verschiedener Fertigungseinflüsse und das Tragverhalten unter Dauerstandslast sowie unter Temperatureinfluss werden im folgenden Beitrag thematisiert.
Aktuelle Erkenntnisse zum Einsatz von Klebstoff in vorgespannten Schraubenverbindungen unter Berücksichtigung von Fertigungseinflüssen
Nicht vorwiegend ruhend beanspruchte Konstruktionen werden im Stahlbau i. Allg. mit gleitfest vorgespannten Verbindungen ausgeführt, da diese aufgrund ihrer reibschlüssigen Kraftübertragung einen hohen Ermüdungswiderstand aufweisen. Die übertragbaren Kräfte in Schraubenverbindungen unter Scherbeanspruchung sind jedoch begrenzt. Wird zusätzlich Klebstoff auf die Reibflächen appliziert, entsteht die sog. vorgespannte Hybridverbindung. Die damit verbundene Traglaststeigerung unter Berücksichtigung verschiedener Fertigungseinflüsse und das Tragverhalten unter Dauerstandslast sowie unter Temperatureinfluss werden im folgenden Beitrag thematisiert.
Numerische Simulation von Vorspannkraftverlusten in Ringflanschverbindungen
Die Betriebsbeanspruchung von Schrauben in Ringflanschverbindungen zur Verbindung von Tragstruktursektionen von Windenergieanlagen wird maßgeblich durch die vorhandene Pressung in der Flanschkontaktfuge beeinflusst, welche durch die eingebrachte Schraubenvorspannkraft erzielt wird. Unter den vorliegenden Belastungen im laufenden Betrieb der Anlage besteht die Möglichkeit, dass durch Plastifizierung im Flansch oder in der Schraube Vorspannkraft verloren geht. In diesem Beitrag wird anhand eines praxisnahen Beispiels gezeigt, ob und – wenn ja – in welcher Größenordnung Vorspannkraftverluste zu erwarten sind und durch welche Einflussfaktoren diese maßgeblich bestimmt werden. Hierzu werden verschiedene Last‐ und Vorspannkraftniveaus sowie unterschiedliche Imperfektionen in Form von Parallelklaffungen untersucht. Auf Basis der durchgeführten numerischen Untersuchungen kann festgehalten werden, dass Vorspannkraftverluste nur in geringer Höhe auftreten und eine hohe Vorspannkraft sich stets positiv auswirkt, auch wenn sich dadurch erste Plastifizierungseffekte schon auf einem niedrigeren Lastniveau einstellen.
Numerische Simulation von Vorspannkraftverlusten in Ringflanschverbindungen
Die Betriebsbeanspruchung von Schrauben in Ringflanschverbindungen zur Verbindung von Tragstruktursektionen von Windenergieanlagen wird maßgeblich durch die vorhandene Pressung in der Flanschkontaktfuge beeinflusst, welche durch die eingebrachte Schraubenvorspannkraft erzielt wird. Unter den vorliegenden Belastungen im laufenden Betrieb der Anlage besteht die Möglichkeit, dass durch Plastifizierung im Flansch oder in der Schraube Vorspannkraft verloren geht. In diesem Beitrag wird anhand eines praxisnahen Beispiels gezeigt, ob und – wenn ja – in welcher Größenordnung Vorspannkraftverluste zu erwarten sind und durch welche Einflussfaktoren diese maßgeblich bestimmt werden. Hierzu werden verschiedene Last‐ und Vorspannkraftniveaus sowie unterschiedliche Imperfektionen in Form von Parallelklaffungen untersucht. Auf Basis der durchgeführten numerischen Untersuchungen kann festgehalten werden, dass Vorspannkraftverluste nur in geringer Höhe auftreten und eine hohe Vorspannkraft sich stets positiv auswirkt, auch wenn sich dadurch erste Plastifizierungseffekte schon auf einem niedrigeren Lastniveau einstellen.
- 23 July 2020
- Published by Wiley in Steel Construction
- Vol. 13 (3) , 223-237
Joints with lockbolts in steel structures – Part 2: Design and execution
Many mechanical joints in steel structures use conventional bolts. Nevertheless, this proven joining technology has some significant disadvantages. These basically include the high levels of scatter during application of the assembly preload using the torque‐controlled tightening process, the risk of loosening during cyclic loads due to transverse displacement of the components and the low fatigue resistance under axial loading. Lockbolt technology was invented as long ago as the 1930s and mainly used for the aviation and space industry because of its evident advantages. This joining technology has been constantly further developed in response to the most diverse demands from sectors such as aviation, commercial vehicles, rail vehicles, agricultural machinery, defence technology and steel structures. The application of lockbolt technology, which is primarily used in mechanical engineering, was in most cases based on individual studies, since no consistent rules and guidelines were available for the design and execution of lockbolt connections in steel structures. Within the scope of several public research projects funded by the AiF (German Federation of Industrial Research Associations) and conducted by the iGF (Industrial Collective Research) organization as well as through approval investigations, the Fraunhofer Institute for Large Structures in Production Engineering (IGP) has successively developed the necessary design rules according to the EN 1993 standard (Eurocode 3) for use in structural connections. These design rules will be presented within the context of this article in order to make the benefits of this joining technology available to other users. In addition, insights into the use of technical approvals will be presented together with some current applications.
- 23 July 2020
- Published by Wiley in Steel Construction
- Vol. 13 (3) , 223-237
Joints with lockbolts in steel structures – Part 2: Design and execution
Many mechanical joints in steel structures use conventional bolts. Nevertheless, this proven joining technology has some significant disadvantages. These basically include the high levels of scatter during application of the assembly preload using the torque‐controlled tightening process, the risk of loosening during cyclic loads due to transverse displacement of the components and the low fatigue resistance under axial loading. Lockbolt technology was invented as long ago as the 1930s and mainly used for the aviation and space industry because of its evident advantages. This joining technology has been constantly further developed in response to the most diverse demands from sectors such as aviation, commercial vehicles, rail vehicles, agricultural machinery, defence technology and steel structures. The application of lockbolt technology, which is primarily used in mechanical engineering, was in most cases based on individual studies, since no consistent rules and guidelines were available for the design and execution of lockbolt connections in steel structures. Within the scope of several public research projects funded by the AiF (German Federation of Industrial Research Associations) and conducted by the iGF (Industrial Collective Research) organization as well as through approval investigations, the Fraunhofer Institute for Large Structures in Production Engineering (IGP) has successively developed the necessary design rules according to the EN 1993 standard (Eurocode 3) for use in structural connections. These design rules will be presented within the context of this article in order to make the benefits of this joining technology available to other users. In addition, insights into the use of technical approvals will be presented together with some current applications.