Abhijit Kar
Research Interests
Abhijit Kar has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
Ajoy Kumar Ray
Material Science & Technology Division, National Metallurgical Laboratory (CSIR), Jamshedpur-831007, India
5 shared publicationsMonalisa Char
Department of Materials Science and Technology Maulana Abul Kalam Azad University of Technology‐WB Haringhata 741249 India
4 shared publicationsAmit K. Chakraborty
Department of Physics National Institute of Technology Durgapur 713209 India
3 shared publicationsMainak Ghosh
3 shared publications- Nguyen Dang Nam
Future Materials & Devices Lab., Institute of Fundamental and Applied Sciences, Duy Tan University, Ho Chi Minh City 70000, Vietnam
3 shared publications A. K. Ray
Materials Science and Technology DivisionNational Metallurgical Laboratory (CSIR), Jamshedpur 831007, India
2 shared publications
Latest Publications
- 23 January 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (5)
Influence of Sn Multilayers on the Scale‐Invariant and Nonlinear Behavior of Cu–SAC–Cu Solder Joint Microstructures
An attempt has been made to improve the quality of the solder joint prepared using Sn multilayer along with SAC305 solder paste with respect to the joints prepared using only the SAC305 solder paste. Comparative results of solder joint properties have been reported. Joint interfaces have been characterized using scanning electron microscopy, X‐ray diffraction, nanoindentation, and cyclic voltammetry (CV). Correlations between different nonlinear behaviors reflected in the microstructural, electrical, and mechanical properties of the solder joints have been established through nonlinear ultrasonic testing and fractal dimensional analysis. Experimentalresults are further modeled to establish a power‐law relationship to detect the scale‐invariant behavior of the solder joints. This power‐law scaling provides an indicator of the underlying microstructural organization and the mode of energy dissipation under mechanical loading within solder joints. Finite element analysis reveals a 46% reduction in peak von Mises stress for Sn multilayer‐induced solder joints compared to their nonlayered counterparts, suggesting their ability to withstand higher forces. CV analysis further indicates superior electrochemical stability on using Sn multilayers for making the solder joints. Sn multilayers not only refine intermetallic compound morphology at the joint interface but also contribute to better distribution of induced stress.
- 23 January 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (5)
Influence of Sn Multilayers on the Scale‐Invariant and Nonlinear Behavior of Cu–SAC–Cu Solder Joint Microstructures
An attempt has been made to improve the quality of the solder joint prepared using Sn multilayer along with SAC305 solder paste with respect to the joints prepared using only the SAC305 solder paste. Comparative results of solder joint properties have been reported. Joint interfaces have been characterized using scanning electron microscopy, X‐ray diffraction, nanoindentation, and cyclic voltammetry (CV). Correlations between different nonlinear behaviors reflected in the microstructural, electrical, and mechanical properties of the solder joints have been established through nonlinear ultrasonic testing and fractal dimensional analysis. Experimentalresults are further modeled to establish a power‐law relationship to detect the scale‐invariant behavior of the solder joints. This power‐law scaling provides an indicator of the underlying microstructural organization and the mode of energy dissipation under mechanical loading within solder joints. Finite element analysis reveals a 46% reduction in peak von Mises stress for Sn multilayer‐induced solder joints compared to their nonlayered counterparts, suggesting their ability to withstand higher forces. CV analysis further indicates superior electrochemical stability on using Sn multilayers for making the solder joints. Sn multilayers not only refine intermetallic compound morphology at the joint interface but also contribute to better distribution of induced stress.
- 8 September 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (22)
Tin Multilayer‐Aided SAC305‐Based Lead‐Free Solder Joint Interface with Cu: An Investigation of the Stress Distribution by Finite Element Analysis and Nanoindentation Studies
Two different types of lead‐free solder joints Cu/(Sn3.0Ag0.5Cu)/Cu and Cu/Sn/(Sn3.0Ag0.5Cu)/Sn/Cu have been investigated. Joints are produced following the transient liquid phase like soldering process. The microstructure of different intermetallic compounds (IMCs) present at the joint interfaces, as well as their indentation hardness and elastic modulus, have been investigated and analyzed using scanning electron microscopy (SEM), X‐ray diffraction (XRD) spectroscopy, and nanoindentation. The exact position of different microcracks inside the interfaces has been identified by analyzing the elastic–plastic properties and interfacial toughness of these solder joints. The modulus and hardness of the Sn multilayer‐assisted solder joint interface are found to be 60.08%, and 90.18% higher than those of its non‐layered counterpart, respectively. The finite element analysis (FEA) has been done to estimate and compute stress distributions over the interfacial region. The dislocation mechanics involved in strengthening the joint strength are related to the nature of stress flow; as observed in FEA. It is reconfirmed that the high susceptibility to brittle failure of the non‐layered Cu‐SAC305 solder joints could be avoided by using a Sn interlayer in between the Cu substrates and the SAC305 solder paste.
- 8 September 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (22)
Tin Multilayer‐Aided SAC305‐Based Lead‐Free Solder Joint Interface with Cu: An Investigation of the Stress Distribution by Finite Element Analysis and Nanoindentation Studies
Two different types of lead‐free solder joints Cu/(Sn3.0Ag0.5Cu)/Cu and Cu/Sn/(Sn3.0Ag0.5Cu)/Sn/Cu have been investigated. Joints are produced following the transient liquid phase like soldering process. The microstructure of different intermetallic compounds (IMCs) present at the joint interfaces, as well as their indentation hardness and elastic modulus, have been investigated and analyzed using scanning electron microscopy (SEM), X‐ray diffraction (XRD) spectroscopy, and nanoindentation. The exact position of different microcracks inside the interfaces has been identified by analyzing the elastic–plastic properties and interfacial toughness of these solder joints. The modulus and hardness of the Sn multilayer‐assisted solder joint interface are found to be 60.08%, and 90.18% higher than those of its non‐layered counterpart, respectively. The finite element analysis (FEA) has been done to estimate and compute stress distributions over the interfacial region. The dislocation mechanics involved in strengthening the joint strength are related to the nature of stress flow; as observed in FEA. It is reconfirmed that the high susceptibility to brittle failure of the non‐layered Cu‐SAC305 solder joints could be avoided by using a Sn interlayer in between the Cu substrates and the SAC305 solder paste.
- 18 August 2021
- Published by Wiley in Advanced Engineering Materials
- Vol. 24 (1) , 2100679
A Comparative Study on the Influence of SAC305 Lead‐Free Solder Sandwiched by Sn on the Micromechanical and Electrical Properties of the Joints
Herein, the favorable influence of sandwich‐stacked Sn/SAC305/Sn multilayers on the micromechanical and electrical properties of the Cu‐Sn/SAC305/Sn‐Cu solder joints over Cu‐SAC305‐Cu joints is reported. Solder joint interface is characterized through X‐ray diffraction spectroscopy, scanning electron microscopy, transmission electron microscopy, scanning tunneling microscopy (STM), and nanoindentation studies. The use of Sn multilayers facilitates the formation of more homogeneously distributed intermetallic compounds (IMCs) with smaller crystallite sizes and higher dislocation densities at the joint interface. Nanoindentation test results manifest that the hardness, modulus, and resistance to plastic deformation of the joint interface for the samples prepared with Sn multilayer are 3.26 GPa, 123.3 GPa, and 1.5 × 109, respectively, much higher and improved than 0.32 GPa, 41.82 GPa, and 5.28 × 105 in turn, found for samples prepared without using Sn multilayers. STM results confirm a much better electron transfer capacity of the solder joint interface that consists of Sn multilayers compared with solder joints produced without incorporation of Sn multilayer. Wherein, Sn multilayer containing solder joint found less prone to be affected by the humid atmosphere compared with nonlayered solder joint, in which, the former is found to be 48% less sensitive toward humidity (85% Rh) than later.
- 18 August 2021
- Published by Wiley in Advanced Engineering Materials
- Vol. 24 (1) , 2100679
A Comparative Study on the Influence of SAC305 Lead‐Free Solder Sandwiched by Sn on the Micromechanical and Electrical Properties of the Joints
Herein, the favorable influence of sandwich‐stacked Sn/SAC305/Sn multilayers on the micromechanical and electrical properties of the Cu‐Sn/SAC305/Sn‐Cu solder joints over Cu‐SAC305‐Cu joints is reported. Solder joint interface is characterized through X‐ray diffraction spectroscopy, scanning electron microscopy, transmission electron microscopy, scanning tunneling microscopy (STM), and nanoindentation studies. The use of Sn multilayers facilitates the formation of more homogeneously distributed intermetallic compounds (IMCs) with smaller crystallite sizes and higher dislocation densities at the joint interface. Nanoindentation test results manifest that the hardness, modulus, and resistance to plastic deformation of the joint interface for the samples prepared with Sn multilayer are 3.26 GPa, 123.3 GPa, and 1.5 × 109, respectively, much higher and improved than 0.32 GPa, 41.82 GPa, and 5.28 × 105 in turn, found for samples prepared without using Sn multilayers. STM results confirm a much better electron transfer capacity of the solder joint interface that consists of Sn multilayers compared with solder joints produced without incorporation of Sn multilayer. Wherein, Sn multilayer containing solder joint found less prone to be affected by the humid atmosphere compared with nonlayered solder joint, in which, the former is found to be 48% less sensitive toward humidity (85% Rh) than later.
- 17 March 2020
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 29 (4) , 2305-2315
Retardation Effect of Tin Multilayer on Sn-3.0Ag-0.5Cu (SAC305)-Based Solder Joint Interface
- 17 March 2020
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 29 (4) , 2305-2315
Retardation Effect of Tin Multilayer on Sn-3.0Ag-0.5Cu (SAC305)-Based Solder Joint Interface
- Open Access
- 2 October 2019
- Published by IntechOpen
Introductory Chapter: Overview of Pb-Free Solders and Effect of Multilayered Thin Film of Sn on the Lead-Free Solder Joint Interface
Open access peer-reviewed chapter
- 2 October 2019
- Published by IntechOpen
Open AccessIntroductory Chapter: Overview of Pb-Free Solders and Effect of Multilayered Thin Film of Sn on the Lead-Free Solder Joint Interface
Open access peer-reviewed chapter
- 1 June 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 243-244
Characterization and modeling of metal-insulator transition (MIT) based tunnel junctions
Continued physical scaling will reduce power dissipation primarily through the reduction in device capacitance; however, a far greater benefit would result if the CMOS FET could be replaced by a fundamentally new device scheme that operates under very low supply voltages. Recently, semiconductor based inter-band tunnel field effect transistors (TFET) have been explored due to their potential to achieve sub kBT/q steep switching swings, enabling low voltage operation. In this work, we explore the abrupt metal to insulator transition (MIT) of vanadium dioxide (VO2) based tunnel junction - a first step towards a correlated electron based steep switching TFET. As illustrated, the metal insulator transition MIT in materials with strong electron correlation can be utilized to modulate the tunnelling current by opening an energy gap around the Fermi level in the OFF-state, and a metal-insulator-metal tunnelling current by collapsing the gap in the ON-state.
- 1 June 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 243-244
Characterization and modeling of metal-insulator transition (MIT) based tunnel junctions
Continued physical scaling will reduce power dissipation primarily through the reduction in device capacitance; however, a far greater benefit would result if the CMOS FET could be replaced by a fundamentally new device scheme that operates under very low supply voltages. Recently, semiconductor based inter-band tunnel field effect transistors (TFET) have been explored due to their potential to achieve sub kBT/q steep switching swings, enabling low voltage operation. In this work, we explore the abrupt metal to insulator transition (MIT) of vanadium dioxide (VO2) based tunnel junction - a first step towards a correlated electron based steep switching TFET. As illustrated, the metal insulator transition MIT in materials with strong electron correlation can be utilized to modulate the tunnelling current by opening an energy gap around the Fermi level in the OFF-state, and a metal-insulator-metal tunnelling current by collapsing the gap in the ON-state.
- 25 April 2012
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 22 (1) , 258-266
Graphite-to-304SS Braze Joining by Active Metal-Brazing Technique: Improvement of Mechanical Properties
- 25 April 2012
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 22 (1) , 258-266
Graphite-to-304SS Braze Joining by Active Metal-Brazing Technique: Improvement of Mechanical Properties
- 1 April 2012
- Published by Taylor & Francis in Materials Technology
- Vol. 27 (2) , 169-172
Structural characterisation of reaction zone for friction stir welded aluminium–stainless steel joint
In the present investigation, commercially pure Al has been joined with 304 stainless steel (SS) by friction stir welding. The assembly finds widespread application in the field of cryogenics, nuclear, structural industries and domestic appliances. Microstructural characterisation was carried out using scanning and transmission electron microscopes. It has been found that diffusion of Fe, Cr and Ni is substantial within Al; however, diffusion of Al within 304SS is limited. Owing to interdiffusion of chemical species across the bondline, discrete islands of Fe3Al intermetallic form within the reaction zone. The rubbing action of tool over the butting edge of 304SS removed fine particles from 304SS, which were embedded in the stirring zone of Al matrix. Subsequently, austenite underwent phase transformation to ferrite due to large strain within this grain. Fracture path mainly moves through stirring zone of Al alloy under tensile loading; however, in some places, presence of Fe3Al compound has been also found.
- 1 April 2012
- Published by Taylor & Francis in Materials Technology
- Vol. 27 (2) , 169-172
Structural characterisation of reaction zone for friction stir welded aluminium–stainless steel joint
In the present investigation, commercially pure Al has been joined with 304 stainless steel (SS) by friction stir welding. The assembly finds widespread application in the field of cryogenics, nuclear, structural industries and domestic appliances. Microstructural characterisation was carried out using scanning and transmission electron microscopes. It has been found that diffusion of Fe, Cr and Ni is substantial within Al; however, diffusion of Al within 304SS is limited. Owing to interdiffusion of chemical species across the bondline, discrete islands of Fe3Al intermetallic form within the reaction zone. The rubbing action of tool over the butting edge of 304SS removed fine particles from 304SS, which were embedded in the stirring zone of Al matrix. Subsequently, austenite underwent phase transformation to ferrite due to large strain within this grain. Fracture path mainly moves through stirring zone of Al alloy under tensile loading; however, in some places, presence of Fe3Al compound has been also found.
- 21 June 2011
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 40 (9) , 1937-1942
Effect of Gold on the Corrosion Behavior of an Electroless Nickel/Immersion Gold Surface Finish
- 21 June 2011
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 40 (9) , 1937-1942
Effect of Gold on the Corrosion Behavior of an Electroless Nickel/Immersion Gold Surface Finish
- 1 May 2010
- Published by SAGE Publications in Materials Science and Technology
- Vol. 26 (5) , 610-614
Effect of Mn on Sn–Ag–Cu ternary lead free solder alloy–Cu assembly: A comparative study
In the present investigation, transition joints were produced by soldering Sn–Ag–Cu and Sn–Ag–Cu–Mn alloys to Cu substrate. Microstructure and mechanical properties of the assemblies were determined in reflowed condition and after aging at 100°C for variable time. The shear strength as well as the reaction layer thickness of Sn–Ag–Cu versus Cu is lower in comparison to Sn–Ag–Cu– Mn versus Cu solder assembly in reflowed condition. The reaction zone for Sn–Ag–Cu versus Cu is decorated with Cu3Sn and Cu6Sn5; however, in the case of Sn–Ag–Cu–Mn versus Cu assembly only Cu6Sn5 was observed. Mn is responsible for enhanced width of Cu6Sn5, which act as a barrier layer restricting the diffusion of Sn across the interface and Cu3Sn formation has not been found even after aging of 200 h. Aging treatment leads to growth of intermetallic layer for both the joints and decrement in shear strength of the assemblies. Still Sn–Ag–Cu–Mn versus Cu solder assembly exhibits superior mechanical strength than Sn–Ag–Cu versus Cu transition joint.
- 1 May 2010
- Published by SAGE Publications in Materials Science and Technology
- Vol. 26 (5) , 610-614
Effect of Mn on Sn–Ag–Cu ternary lead free solder alloy–Cu assembly: A comparative study
In the present investigation, transition joints were produced by soldering Sn–Ag–Cu and Sn–Ag–Cu–Mn alloys to Cu substrate. Microstructure and mechanical properties of the assemblies were determined in reflowed condition and after aging at 100°C for variable time. The shear strength as well as the reaction layer thickness of Sn–Ag–Cu versus Cu is lower in comparison to Sn–Ag–Cu– Mn versus Cu solder assembly in reflowed condition. The reaction zone for Sn–Ag–Cu versus Cu is decorated with Cu3Sn and Cu6Sn5; however, in the case of Sn–Ag–Cu–Mn versus Cu assembly only Cu6Sn5 was observed. Mn is responsible for enhanced width of Cu6Sn5, which act as a barrier layer restricting the diffusion of Sn across the interface and Cu3Sn formation has not been found even after aging of 200 h. Aging treatment leads to growth of intermetallic layer for both the joints and decrement in shear strength of the assemblies. Still Sn–Ag–Cu–Mn versus Cu solder assembly exhibits superior mechanical strength than Sn–Ag–Cu versus Cu transition joint.