QYQi Yang

Qi Yang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Qi Yang has a total of 9 co-authors. Here are the top co-authors by number of shared publications:

  • Decai Feng

    College of Polymer Science and Engineering, The State Key Laboratory for Polymer Materials Engineering, Sichuan University , Chengdu, PR, China

    2 shared publications
  • Guangxian Li

    College of Polymer Science and Engineering, The State Key Laboratory for Polymer Materials Engineering, Sichuan University, Chengdu 610065, People's Republic of China

    2 shared publications
  • Kun Yang

    College of Polymer Science and Engineering, The State Key Laboratory for Polymer Materials Engineering, Sichuan University, Chengdu 610065, People's Republic of China

    2 shared publications
  • Guangxian Li

    Sichuan Univ, Coll Polymer Sci & Engn, State Key Lab Polymer Mat Engn China, Chengdu 610065, Peoples R China

    1 shared publication
  • Junjie Kuang

    College of Polymer Science and Engineering, The State Key Laboratory for Polymer Materials Engineering, Sichuan University, Chengdu 610065, People's Republic of China

    1 shared publication
  • Xiaolin Liu

    College of Polymer Science and Engineering, The State Key Laboratory for Polymer Materials Engineering, Sichuan University , Chengdu, PR, China

    1 shared publication

Latest Publications

  • Preparation and Properties of Fragrant Acrylonitrile-Butadiene-Styrene Composites

    by Xiaolin Liu, Qi Yang, Zhiqiang Jiang, Decai Feng, Guangxian Li

    The aim of the present work is to upgrade the functionality and applicability of acrylonitrile-butadiene-styrene (ABS) composites by means of a blending technique. Fragrant ABS composites were prepared by adding a fragrance into the ABS matrix. It was found that the volatility of the essence was greatly affected by the nature of the essence, the environmental temperature and the polymer matrix. In addition, the impact strength and yield strength decreased gradually with increasing fragrance content, but the processing properties were improved rapidly and rate of elongation at the break increased rapidly. The fragrance of the fragrant ABS composites could be maintained for a long time at room temperature.


  • Mechanical properties and morphologies of polypropylene with different sizes of glass bead particles

    by Kun Yang, Qi Yang, Guangxian Li, Junjie Kuang, Ziqiang Jiang

    A commercial grade of isotactic polypropylene (PP) was used to study the mechanical properties and morphologies of the PP composites filled with four sizes of glass bead particles. The glass bead particles used were with average particle sizes of 15 μm (GB15), 10 μm (GB10), 5 μm (GB5), and 2.5 μm (GB2.5), respectively. It was clear that the glass bead size was an important factor on the determination of mechanical properties of the composites. As a whole, in view of the scatter in the data, under the condition of same filler content, the yield strength and impact strength of the composites filled with smaller glass bead particles was higher than those of the composites filled with bigger ones. And the flexural strength and modulus of the composites filled with GB10, GB5, or GB2.5 particles could be regarded as the same. The flexural strength and modulus of the composites filled with GB15 particles were higher than those of the composites filled with other three sizes of particles. Among four sizes of glass bead particles, GB2.5 had the best toughening effect to improve the impact strength of PP matrix. And the major toughening mechanism of the PP/GB2.5 composites was the pinning effect introduced by GB2.5. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers


  • Mechanical properties and morphologies of polypropylene with different sizes of calcium carbonate particles

    by Kun Yang, Qi Yang, Guangxian Li, Yajie Sun, Decai Feng

    Three polypropylene (PP) matrixes with different intrinsic toughness were used to study the morphologies and mechanical properties of PP filled with four sizes of calcium carbonate particles. PP1 was a homopolymer, PP2 was a propylene‐ethylene copolymer, and PP3 was a mixture of PP1 and PP2 (PP1:PP2 = 1:1, weight ratio). Calcium carbonate (CC25, CC4, CC1.8, and CC0.07) with an average particle size of 25, 4, 1.8, and 0.07 μm, respectively, was used. It was clear that the PP matrix and filler size had key effects on improvement of mechanical properties of PP matrix. For all three PP matrixes, the yield strength, the flexural strength and modulus of the composites filled with CC25, CC4, and CC1.8 could be regarded as the same. But the yield strength, the flexural strength and modulus of composites filled with CC0.07 were obviously lower than those of composites filled with other sizes of particles. Among four sizes of calcium carbonate particles, CC0.07 had the best toughening effect to improve the impact strength of PP matrix, and the toughening effect of CC0.07 was influenced by PP matrix. For all PP matrixes, only in the case of moderate matrix toughness (PP3 matrix), the composite could receive the highest extent of toughness increase (4.3 times that of matrix). With regard to all PP composites, the best combination of properties was PP2 nanocomposite filled with 20 wt% CC0.07. POLYM. COMPOS., 27:443–450, 2006. © 2006 Society of Plastics Engineers