Emmanuel Pacheco Rocha Lima
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Emmanuel Pacheco Rocha Lima has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Pedro Cunha de Lima
Instituto Federal da Bahia – IFBA – Campus Barreiras, Av. das Várzeas s/n, Centro, Barreiras/BA/Brazil CEP: 47805-970
5 shared publications Marcelo Nava
3 shared publications- Igor Carvalho Da Silva
Universidade de Brasília - UnB, Faculdade do Gama – FGA – Gama, DF, Brasil
2 shared publications Abraão P. Dias
UnB-FGA-Universidade de Brasília-Faculdade do Gama, Área Especial, Projeção A, Setor Leste, Gama, DF, Brazil
1 shared publication- Abraão Pereira Dias
Universidade de Brasília, Brasil
1 shared publication - Abraão Pereira Dias
Universidade de Brasília - UnB, Faculdade do Gama – FGA – Gama, DF, Brasil
1 shared publication
Latest Publications
- 6 March 2025
- Published by Springer Nature in MRS Advances
- Vol. 10 (7) , 898-903
Study of slag different concentrations influence on the mechanical properties of particulates aluminum matrix composites produced by powder metallurgy
- 6 March 2025
- Published by Springer Nature in MRS Advances
- Vol. 10 (7) , 898-903
Study of slag different concentrations influence on the mechanical properties of particulates aluminum matrix composites produced by powder metallurgy
- Open Access
- 13 January 2024
- Published by Qeios Ltd
Review of: "The Influence of Hot Extrusion on The Mechanical and Wear Properties of an Al6063 Metal Matrix Composite Reinforced With Silicon Carbide Particulates"
Review: 1. HOW MANY SAMPLES WERE USED FOR EACH TEST CARRIED OUT? WERE THE AVERAGES AND DEVIATIONS OF THE VALUES OBTAINED? 2. THE VALUES FOR THE ELASTICITY MODULUS OBTAINED FOR THE 6063 ALUMINUM ALLOY WITHOUT REINFORCEMENT WERE VERY LOW, ABOUT ¼ (15...
- 13 January 2024
- Published by Qeios Ltd
Open AccessReview of: "The Influence of Hot Extrusion on The Mechanical and Wear Properties of an Al6063 Metal Matrix Composite Reinforced With Silicon Carbide Particulates"
Review: 1. HOW MANY SAMPLES WERE USED FOR EACH TEST CARRIED OUT? WERE THE AVERAGES AND DEVIATIONS OF THE VALUES OBTAINED? 2. THE VALUES FOR THE ELASTICITY MODULUS OBTAINED FOR THE 6063 ALUMINUM ALLOY WITHOUT REINFORCEMENT WERE VERY LOW, ABOUT ¼ (15...
- Open Access
- 1 January 2024
- Published by Even3
- Vol. 26, 1
EFEITO DA ADIÇÃO DE DIFERENTES CONCENTRAÇÕES DE REFORÇO PARTICULADO NA DENSIDADE, DUREZA E RESISTÊNCIA AO DESGASTE DE COMPÓSITOS DE ALUMÍNIO PRODUZIDOS VIA METALURGIA DO PÓ
O objetivo deste trabalho é avaliar a influência da adição de diferentes concentrações de reforço particulado na produção de compósitos de alumínio comercialmente puro reforçados com escória de alto forno via metalurgia do pó. O processamento desses materiais foi realizado através do peneiramento, mistura e compactação de pós de alumínio reforçado com 5, 10 e 15% de escória de alto-forno. A compactação uniaxial a frio foi realizada a uma pressão de 430 MPa. Os materiais obtidos foram sinterizados a 610°C por 2h sob atmosfera inerte. Amostras de alumínio não reforçadas também foram produzidas. A caracterização dos materiais foi realizada por meio de medições de densidade e microdureza e ensaios de desgaste. A análise morfológica foi realizada por microscopia eletrônica de varredura. Como resultados, os materiais apresentaram densidade relativa superior a 93,9%, chegando a 98,6% para o alumínio puro. Os compósitos apresentaram distribuição homogênea das partículas de reforço e melhoria progressiva da microdureza com o aumento da concentração de escória. Porém, em relação à resistência ao desgaste, o resultado foi o oposto. Este resultado sugere que as partículas de reforço, por serem de material cerâmico, podem ter funcionado como abrasivo quando desprendidas da matriz de alumínio, uma vez que o alumínio comercialmente puro é extremamente maleável e não consegue segurar as partículas de escória.
- 1 January 2024
- Published by Even3
- Vol. 26, 1
Open AccessEFEITO DA ADIÇÃO DE DIFERENTES CONCENTRAÇÕES DE REFORÇO PARTICULADO NA DENSIDADE, DUREZA E RESISTÊNCIA AO DESGASTE DE COMPÓSITOS DE ALUMÍNIO PRODUZIDOS VIA METALURGIA DO PÓ
O objetivo deste trabalho é avaliar a influência da adição de diferentes concentrações de reforço particulado na produção de compósitos de alumínio comercialmente puro reforçados com escória de alto forno via metalurgia do pó. O processamento desses materiais foi realizado através do peneiramento, mistura e compactação de pós de alumínio reforçado com 5, 10 e 15% de escória de alto-forno. A compactação uniaxial a frio foi realizada a uma pressão de 430 MPa. Os materiais obtidos foram sinterizados a 610°C por 2h sob atmosfera inerte. Amostras de alumínio não reforçadas também foram produzidas. A caracterização dos materiais foi realizada por meio de medições de densidade e microdureza e ensaios de desgaste. A análise morfológica foi realizada por microscopia eletrônica de varredura. Como resultados, os materiais apresentaram densidade relativa superior a 93,9%, chegando a 98,6% para o alumínio puro. Os compósitos apresentaram distribuição homogênea das partículas de reforço e melhoria progressiva da microdureza com o aumento da concentração de escória. Porém, em relação à resistência ao desgaste, o resultado foi o oposto. Este resultado sugere que as partículas de reforço, por serem de material cerâmico, podem ter funcionado como abrasivo quando desprendidas da matriz de alumínio, uma vez que o alumínio comercialmente puro é extremamente maleável e não consegue segurar as partículas de escória.
- Open Access
- 8 December 2023
- Published by Universidade Federal de Vicosa in The Journal of Engineering and Exact Sciences
- Vol. 9 (12) , 17468
Effect of the addition of different concentrations of particulate reinforcement on the density, hardness and wear resistance of aluminum composites produced by powder metallurgy
The objective of this work is to evaluate the influence of the addition of different concentrations of particulate reinforcement in the production of commercially pure aluminum composites reinforced with blast-furnace slag via powder metallurgy. The processing of these materials was done by sieving, mixing and compacting powders of reinforced aluminum with 5, 10 and 15% of blast-furnace slag. The cold uniaxial compaction was realized at a pressure of 430 MPa. The obtained materials were sintered at 610°C for 2h under inert atmosphere. Unreinforced aluminum samples were also produced. The characterization of the materials was realized by density and microhardness measurements and wear tests. The morphological analysis was realized by scanning electron microscopy. As results, the materials had a relative density greater than 93,8%, reaching 98,6% for pure aluminum. The composites showed a homogeneous distribution of reinforcement particles and progressive improvement in microhardness with increasing slag concentration. However, regarding wear resistance, the result was the opposite. This result suggests that the reinforcing particles, being made of ceramic material, may have worked as an abrasive when released from the aluminum matrix, since commercially pure aluminum is extremely malleable and cannot hold the slag particles.
- 8 December 2023
- Published by Universidade Federal de Vicosa in The Journal of Engineering and Exact Sciences
- Vol. 9 (12) , 17468
Open AccessEffect of the addition of different concentrations of particulate reinforcement on the density, hardness and wear resistance of aluminum composites produced by powder metallurgy
The objective of this work is to evaluate the influence of the addition of different concentrations of particulate reinforcement in the production of commercially pure aluminum composites reinforced with blast-furnace slag via powder metallurgy. The processing of these materials was done by sieving, mixing and compacting powders of reinforced aluminum with 5, 10 and 15% of blast-furnace slag. The cold uniaxial compaction was realized at a pressure of 430 MPa. The obtained materials were sintered at 610°C for 2h under inert atmosphere. Unreinforced aluminum samples were also produced. The characterization of the materials was realized by density and microhardness measurements and wear tests. The morphological analysis was realized by scanning electron microscopy. As results, the materials had a relative density greater than 93,8%, reaching 98,6% for pure aluminum. The composites showed a homogeneous distribution of reinforcement particles and progressive improvement in microhardness with increasing slag concentration. However, regarding wear resistance, the result was the opposite. This result suggests that the reinforcing particles, being made of ceramic material, may have worked as an abrasive when released from the aluminum matrix, since commercially pure aluminum is extremely malleable and cannot hold the slag particles.
- Open Access
- 26 June 2023
- Published by Universidade Federal de Vicosa in The Journal of Engineering and Exact Sciences
- Vol. 9 (9) , 17474-01e
Caracterização das propriedades de sinterização de termoplásticos: um estudo exploratório para avaliar sua viabilidade como um método eficaz de fabricação
- 26 June 2023
- Published by Universidade Federal de Vicosa in The Journal of Engineering and Exact Sciences
- Vol. 9 (9) , 17474-01e
Open AccessCaracterização das propriedades de sinterização de termoplásticos: um estudo exploratório para avaliar sua viabilidade como um método eficaz de fabricação
- 28 April 2020
- Published by David Publishing Company in Journal of Materials Science and Engineering A
- Vol. 10 (2)
Comparisson of Recrystallization Kinetics and Grain Growth in Polycrystalline Shape Memory Alloys
- 28 April 2020
- Published by David Publishing Company in Journal of Materials Science and Engineering A
- Vol. 10 (2)
Comparisson of Recrystallization Kinetics and Grain Growth in Polycrystalline Shape Memory Alloys
- Open Access
- 28 April 2020
- Published by David Publishing Company in Journal of Materials Science and Engineering A
- Vol. 10 (2)
Influence of the Deep Cryogenic Treatment at the Stabilization of Martensitic Transformation Temperatures at the Smart Material Alloy Cu-14Al-4Ni
- 28 April 2020
- Published by David Publishing Company in Journal of Materials Science and Engineering A
- Vol. 10 (2)
Open AccessInfluence of the Deep Cryogenic Treatment at the Stabilization of Martensitic Transformation Temperatures at the Smart Material Alloy Cu-14Al-4Ni
- Open Access
- 16 December 2019
- Published by Universidad Santo Tomas in ITECKNE
- Vol. 16 (2) , 32-39
Thermomechanical response of a viscoelastic Ni-Ti – Shape Memory Alloy composite beam
This investigation is concerned with the mechanical behavior of Shape Memory Alloy Hybrid Composite Beams (SMAHC), that consist of a circular bar of NiTi alloy incorporated in a 500 mm long cylindrical pipe of polypropylene (PP), with external diameter 50 mm and nominal wall thickness 7 mm, wound with a nylon/epoxy layer. The Ni-Ti alloy was characterized using: scanning electron microscopy (SEM); X-ray diffraction (XRD) and Differential thermal analysis (DSC). The nominal chemical composition of the alloy is 50.05 %Ni / 49.95%Ti, and the softer martensite is the predominant phase at room temperature. The approximate martensite (M) to Austenitic (A) phase transformation temperatures were Mstart = 32°C, Mfinal = 46°C, Astart = 38 °C and Afinal = 60°C. For temperature TAfinal it is fully converted in the Austenitic phase; and its elasticity modulus increases by a factor up to three times. This significant change in stiffness of Ni-Ti, without changing its mass, has motivated the application of such alloy in machine vibration control. The SMAHC beams were subjected to static three-point bending tests, in the elastic regime. Experimental results showed that, in average, at 21°C, the PP pipes effective flexural elastic modulus increased 112%, from 757 MPa to 1609 MPa, when the Ni-Ti bar and the external layer of nylon/epoxy were incorporated to the PP pipe, creating a smart beam. These last results indicate that the SMAHC beam can work as an adaptative structure.
- 16 December 2019
- Published by Universidad Santo Tomas in ITECKNE
- Vol. 16 (2) , 32-39
Open AccessThermomechanical response of a viscoelastic Ni-Ti – Shape Memory Alloy composite beam
This investigation is concerned with the mechanical behavior of Shape Memory Alloy Hybrid Composite Beams (SMAHC), that consist of a circular bar of NiTi alloy incorporated in a 500 mm long cylindrical pipe of polypropylene (PP), with external diameter 50 mm and nominal wall thickness 7 mm, wound with a nylon/epoxy layer. The Ni-Ti alloy was characterized using: scanning electron microscopy (SEM); X-ray diffraction (XRD) and Differential thermal analysis (DSC). The nominal chemical composition of the alloy is 50.05 %Ni / 49.95%Ti, and the softer martensite is the predominant phase at room temperature. The approximate martensite (M) to Austenitic (A) phase transformation temperatures were Mstart = 32°C, Mfinal = 46°C, Astart = 38 °C and Afinal = 60°C. For temperature TAfinal it is fully converted in the Austenitic phase; and its elasticity modulus increases by a factor up to three times. This significant change in stiffness of Ni-Ti, without changing its mass, has motivated the application of such alloy in machine vibration control. The SMAHC beams were subjected to static three-point bending tests, in the elastic regime. Experimental results showed that, in average, at 21°C, the PP pipes effective flexural elastic modulus increased 112%, from 757 MPa to 1609 MPa, when the Ni-Ti bar and the external layer of nylon/epoxy were incorporated to the PP pipe, creating a smart beam. These last results indicate that the SMAHC beam can work as an adaptative structure.
- 9 September 2019
- Published by Springer Nature in MRS Advances
- Vol. 4 (54) , 2969-2976
Preparation and Characterization of AA6061 Aluminum Alloy Composite Reinforced With Different Contents of Blast-Furnace Slag by Powder Metalurgy
- 9 September 2019
- Published by Springer Nature in MRS Advances
- Vol. 4 (54) , 2969-2976
Preparation and Characterization of AA6061 Aluminum Alloy Composite Reinforced With Different Contents of Blast-Furnace Slag by Powder Metalurgy
- 1 October 2015
- Published by Springer Nature in MRS Proceedings
- Vol. 1765, 127-132
Determination of Recrystallization Kinetics and Activation Energy of Grain Growth Process of Cu-14Al-4Ni Shape Memory Alloy
- 1 October 2015
- Published by Springer Nature in MRS Proceedings
- Vol. 1765, 127-132
Determination of Recrystallization Kinetics and Activation Energy of Grain Growth Process of Cu-14Al-4Ni Shape Memory Alloy