Xiaopeng Jia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xiaopeng Jia has a total of 134 co-authors. Here are the top co-authors by number of shared publications:
- Hongan Ma
National Key Lab of Superhard Materials, Jilin University, Changchun 130012, China
24 shared publications - Liangchao Chen
School of Physics and Microelectronics, Zhengzhou University, Zhengzhou 450052, China
12 shared publications Shuai Fang
Jilin Univ, Coll Phys, State Key Lab Superhard Mat, Changchun 130012, Peoples R China
12 shared publications- Chao Fang
School of Physics and Laboratory of Zhongyuan Light, Zhengzhou University, Zhengzhou 450052, China
8 shared publications Zhiwen Wang
State Key Laboratory of High Pressure and Superhard Materials, College of Physics, Jilin University, Changchun 130012, Jilin, China
8 shared publicationsHongAn Ma
Jilin University
6 shared publications
Latest Publications
- 18 July 2025
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 27 (33) , 5644-5651
Synthesis and characterization of TiP-doped diamond in the FeNi–C system under HTHP conditions
Synthesis and properties of n-type semiconducting diamonds with TiP addition in the FeNi–C system under HTHP conditions.
- 18 July 2025
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 27 (33) , 5644-5651
Synthesis and characterization of TiP-doped diamond in the FeNi–C system under HTHP conditions
Synthesis and properties of n-type semiconducting diamonds with TiP addition in the FeNi–C system under HTHP conditions.
- Open Access
- 15 March 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (6) , 446
Theoretical Calculation and Experimental Studies of Boron Phosphide Polycrystalline Synthesized at High Pressure and High Temperature
In this study, a combination of theoretical calculations and experiments were carried out to analyze boron phosphide materials. Amorphous boron powder and amorphous red phosphorus were used as raw materials to directly synthesize the target samples in one step under high-pressure and high-temperature (HPHT) conditions. Theoretical calculations were then carried out based on the XRD spectra of boron phosphide at 4 GPa and 1200 °C. The experimental results show that the target samples can be successfully prepared at HPHT. The electrical properties of the samples were characterized, and it was found that their conductivity increased with the increase in temperature, and they have a semiconducting nature, which is consistent with the theoretical calculations. Its Seebeck coefficient is positive at different temperatures, indicating that the synthesized boron phosphide is a P-type semiconductor. The combination of theoretical calculations and experiments shows that high pressure can reduce the lattice constant of boron phosphide, thus reducing its forbidden bandwidth, which improves its electrical properties. EDS shows a homogeneous distribution of the elements in the samples. Successful synthesis of BP crystals will probably stimulate more research into its semiconductor properties. It may also provide some assistance in the application of BP in aero-engine high-temperature monitoring systems as well as thermally controlled coatings for deep-space probes.
- 15 March 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (6) , 446
Open AccessTheoretical Calculation and Experimental Studies of Boron Phosphide Polycrystalline Synthesized at High Pressure and High Temperature
In this study, a combination of theoretical calculations and experiments were carried out to analyze boron phosphide materials. Amorphous boron powder and amorphous red phosphorus were used as raw materials to directly synthesize the target samples in one step under high-pressure and high-temperature (HPHT) conditions. Theoretical calculations were then carried out based on the XRD spectra of boron phosphide at 4 GPa and 1200 °C. The experimental results show that the target samples can be successfully prepared at HPHT. The electrical properties of the samples were characterized, and it was found that their conductivity increased with the increase in temperature, and they have a semiconducting nature, which is consistent with the theoretical calculations. Its Seebeck coefficient is positive at different temperatures, indicating that the synthesized boron phosphide is a P-type semiconductor. The combination of theoretical calculations and experiments shows that high pressure can reduce the lattice constant of boron phosphide, thus reducing its forbidden bandwidth, which improves its electrical properties. EDS shows a homogeneous distribution of the elements in the samples. Successful synthesis of BP crystals will probably stimulate more research into its semiconductor properties. It may also provide some assistance in the application of BP in aero-engine high-temperature monitoring systems as well as thermally controlled coatings for deep-space probes.
- 5 September 2024
- Published by Springer Nature in Acta Mechanica Sinica
- Vol. 41 (3) , 1-8
Scheme to increase the ultimate pressure of the China-type cubic press
- 5 September 2024
- Published by Springer Nature in Acta Mechanica Sinica
- Vol. 41 (3) , 1-8
Scheme to increase the ultimate pressure of the China-type cubic press
- 1 July 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (7)
A reasonable method to reduce the volume of the WC anvil
With the continuous development of the diamond industry, the China-type cubic press (CCP) has gradually become larger. As a result, the volume of the tungsten carbide (WC) anvil has been increased. Considering that the WC anvil is sintered, a larger volume will deteriorate sintering quality, which could facilitate the formation of cracks during its operation. One feasible way to reduce the volume of the WC anvil is to decrease its diameter and height. Along these lines, in this work, by performing finite element simulations, it was found that a reduction in the diameter of the WC anvil would increase the von Mises stress (VMS) during the synthesis process, as well as reduce the service life of the WC anvil and the ultimate pressure of the CCP. At the same time, a smaller diameter of the WC anvil would cause a significant increase in the VMS of the base steel block, exceeding its yield limit. In addition, a reduction in the height of the WC anvil would lessen the VMS during the synthesis process, and the VMS of the base steel block will also decrease. A reduction in the height of the WC anvil will decrease the pretightening force on the WC anvil, thereby reducing its lateral support effect. When the interference fit was increased from 0.6 to 0.8 mm and the steel ring angle was changed from 1.5° to 1.1°, the pretightening force on the low WC anvil was similar to the pretightening force on the original WC anvil. Our work provides valuable insights for effectively reducing the volume of the WC anvil.
- 1 July 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (7)
A reasonable method to reduce the volume of the WC anvil
With the continuous development of the diamond industry, the China-type cubic press (CCP) has gradually become larger. As a result, the volume of the tungsten carbide (WC) anvil has been increased. Considering that the WC anvil is sintered, a larger volume will deteriorate sintering quality, which could facilitate the formation of cracks during its operation. One feasible way to reduce the volume of the WC anvil is to decrease its diameter and height. Along these lines, in this work, by performing finite element simulations, it was found that a reduction in the diameter of the WC anvil would increase the von Mises stress (VMS) during the synthesis process, as well as reduce the service life of the WC anvil and the ultimate pressure of the CCP. At the same time, a smaller diameter of the WC anvil would cause a significant increase in the VMS of the base steel block, exceeding its yield limit. In addition, a reduction in the height of the WC anvil would lessen the VMS during the synthesis process, and the VMS of the base steel block will also decrease. A reduction in the height of the WC anvil will decrease the pretightening force on the WC anvil, thereby reducing its lateral support effect. When the interference fit was increased from 0.6 to 0.8 mm and the steel ring angle was changed from 1.5° to 1.1°, the pretightening force on the low WC anvil was similar to the pretightening force on the original WC anvil. Our work provides valuable insights for effectively reducing the volume of the WC anvil.
- 1 September 2022
- Published by IOP Publishing in Chinese Physics B
- Vol. 31 (10) , 108104
Effect of the codoping of N–H–O on the growth characteristics and defects of diamonds under high temperature and high pressure
Diamond crystals were synthesized with different doping proportions of N–H–O at 5.5 GPa–7.1 GPa and 1370 °C–1450 °C. With the increase in the N–H–O doping ratio, the crystal growth rate decreased, the temperature and pressure conditions required for diamond nucleation became increasingly stringent, and the diamond crystallization process was affected. [111] became the dominant plane of diamonds; surface morphology became block-like; and growth texture, stacking faults, and etch pits increased. The diamond crystals had a two-dimensional growth habit. Increasing the doping concentration also increased the amount of N that entered the diamond crystals as confirmed via Fourier transform infrared spectroscopy. However, crystal quality gradually deteriorated as verified by the red-shifting of Raman peak positions and the widening of the Raman full width at half maximum. With the increase in the doping ratio, the photoluminescence property of the diamond crystals also drastically changed. The intensity of the N vacancy center of the diamond crystals changed, and several Ni-related defect centers, such as the NE1 and NE3 centers, appeared. Diamond synthesis in N–H–O-bearing fluid provides important information for deepening our understanding of the growth characteristics of diamonds in complex systems and the formation mechanism of natural diamonds, which are almost always N-rich and full of various defect centers. Meanwhile, this study proved that the type of defect centers in diamond crystals could be regulated by controlling the N–H–O impurity contents of the synthesis system.
- 1 September 2022
- Published by IOP Publishing in Chinese Physics B
- Vol. 31 (10) , 108104
Effect of the codoping of N–H–O on the growth characteristics and defects of diamonds under high temperature and high pressure
Diamond crystals were synthesized with different doping proportions of N–H–O at 5.5 GPa–7.1 GPa and 1370 °C–1450 °C. With the increase in the N–H–O doping ratio, the crystal growth rate decreased, the temperature and pressure conditions required for diamond nucleation became increasingly stringent, and the diamond crystallization process was affected. [111] became the dominant plane of diamonds; surface morphology became block-like; and growth texture, stacking faults, and etch pits increased. The diamond crystals had a two-dimensional growth habit. Increasing the doping concentration also increased the amount of N that entered the diamond crystals as confirmed via Fourier transform infrared spectroscopy. However, crystal quality gradually deteriorated as verified by the red-shifting of Raman peak positions and the widening of the Raman full width at half maximum. With the increase in the doping ratio, the photoluminescence property of the diamond crystals also drastically changed. The intensity of the N vacancy center of the diamond crystals changed, and several Ni-related defect centers, such as the NE1 and NE3 centers, appeared. Diamond synthesis in N–H–O-bearing fluid provides important information for deepening our understanding of the growth characteristics of diamonds in complex systems and the formation mechanism of natural diamonds, which are almost always N-rich and full of various defect centers. Meanwhile, this study proved that the type of defect centers in diamond crystals could be regulated by controlling the N–H–O impurity contents of the synthesis system.
- 4 February 2022
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 24 (9) , 1773-1781
Study on the effect of N–H–O co-doping on diamond growth and its mechanism under HPHT by FeNi solvent
The synthesis of diamonds with rich nitrogen (N), hydrogen (H) and oxygen (O) elements is a hot topic that needs to be solved in current research. In this work, diamonds were synthesized with C6H5NO2 dopants using iron and nickel (FeNi) catalysts under conditions of 5.8 GPa and 1370 °C. We characterized N, H, O co-doped diamonds in detail and profoundly researched the effect of N, H, O on FeNi catalysts. The results indicate that with the increase in the content of C6H5NO2, the crystal growth texture is increasingly obvious, and the surface morphology is increasingly uneven and is eventually cracked. Besides, we noticed that the growth rate of the crystal slowed from 2.07 mg h−1 to 0.15 mg h−1. Using Fourier transform infrared (FTIR) spectroscopy, we calculated the N concentration inside the crystal; it increased from 154 ppm to 1218 ppm. The Raman spectra indicate that all the synthesized crystals had a high-quality sp3 structure. X-ray photoelectron spectroscopy (XPS) proved that a small amount of H, O, N entered the lattice of the diamonds. XPS measurement of the metal solvent illustrated that in the doped carbon sources, more oxygen and nitrogen-related components were formed and the proportion of diamond was decreased. SEM-EDS mapping confirms that when the carbon sources are doped with C6H5NO2, the mutual diffusion between carbon sources and the metal solvent is inhibited. XRD results confirmed that when doped, FeN, FeO and FeC8 emerge, while indispensable intermediates for diamond growth vanish. These results ascertain that with the induction of C6H5NO2 in the synthesis cavity, the metal solvent tends to react with the decomposition products of C6H5NO2, thus affecting the graphite conversion to diamond from the carbon source as well as the mutual diffusion between carbon sources and the metal solvent, which eventually leads to the reduction of crystal growth rate. This work further explains the mechanism of decreasing the growth rate and improving the growth conditions of diamonds synthesized using the FeNi catalyst under the condition of N–H–O doping, which provides valuable data for synthesizing diamonds with rich N, H and O content.
- 4 February 2022
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 24 (9) , 1773-1781
Study on the effect of N–H–O co-doping on diamond growth and its mechanism under HPHT by FeNi solvent
The synthesis of diamonds with rich nitrogen (N), hydrogen (H) and oxygen (O) elements is a hot topic that needs to be solved in current research. In this work, diamonds were synthesized with C6H5NO2 dopants using iron and nickel (FeNi) catalysts under conditions of 5.8 GPa and 1370 °C. We characterized N, H, O co-doped diamonds in detail and profoundly researched the effect of N, H, O on FeNi catalysts. The results indicate that with the increase in the content of C6H5NO2, the crystal growth texture is increasingly obvious, and the surface morphology is increasingly uneven and is eventually cracked. Besides, we noticed that the growth rate of the crystal slowed from 2.07 mg h−1 to 0.15 mg h−1. Using Fourier transform infrared (FTIR) spectroscopy, we calculated the N concentration inside the crystal; it increased from 154 ppm to 1218 ppm. The Raman spectra indicate that all the synthesized crystals had a high-quality sp3 structure. X-ray photoelectron spectroscopy (XPS) proved that a small amount of H, O, N entered the lattice of the diamonds. XPS measurement of the metal solvent illustrated that in the doped carbon sources, more oxygen and nitrogen-related components were formed and the proportion of diamond was decreased. SEM-EDS mapping confirms that when the carbon sources are doped with C6H5NO2, the mutual diffusion between carbon sources and the metal solvent is inhibited. XRD results confirmed that when doped, FeN, FeO and FeC8 emerge, while indispensable intermediates for diamond growth vanish. These results ascertain that with the induction of C6H5NO2 in the synthesis cavity, the metal solvent tends to react with the decomposition products of C6H5NO2, thus affecting the graphite conversion to diamond from the carbon source as well as the mutual diffusion between carbon sources and the metal solvent, which eventually leads to the reduction of crystal growth rate. This work further explains the mechanism of decreasing the growth rate and improving the growth conditions of diamonds synthesized using the FeNi catalyst under the condition of N–H–O doping, which provides valuable data for synthesizing diamonds with rich N, H and O content.
- 15 December 2021
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 24 (4) , 886-892
Effects of pressure on the phase transformations and mechanical properties of 10 mol% Mg-PSZ sintered by HPHT
MgO (10 mol%)-stabilized zirconia ceramics were obtained using high-pressure high-temperature (HPHT) sintering.
- 15 December 2021
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 24 (4) , 886-892
Effects of pressure on the phase transformations and mechanical properties of 10 mol% Mg-PSZ sintered by HPHT
MgO (10 mol%)-stabilized zirconia ceramics were obtained using high-pressure high-temperature (HPHT) sintering.
- 14 July 2021
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 23 (35) , 6070-6078
The characteristics of Ib diamond crystals synthesized in a Fe–Ni–C system with different SiC contents
Silicon carbide (SiC) is a substance found in natural diamond inclusions. Analyzing the influence of SiC doping on the properties of synthetic diamonds is vital to understanding the growth mechanism of natural diamonds and the material composition of the mantle. In this work, China-type large volume cubic high-pressure apparatus (CHPA) (SPD-6 × 1200) was used to simulate the high-temperature and high-pressure environment of diamond growth. The influence of different SiC doping contents on the crystal characteristics of a Ib-type diamond synthesized in a Fe–Ni–C system was investigated at a pressure of 5.8 GPa and a temperature range of 1650–1670 K. Optical microscopy (OM), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy (Raman), X-ray photoelectron spectroscopy (XPS), and photoluminescence spectroscopy (PL) were used to characterize the synthesized crystals. The OM results show that the growth rate of the diamond decreases gradually, and the color changes from yellow to light yellow with an increase in the doping concentration. The FTIR results indicate that the nitrogen element in the crystal mainly appears in the diamond crystal in monatomic form (C center). The nitrogen content in the diamond gradually decreases from 275 ppm to 115 ppm with an increase in the SiC dopant ratio. The Raman data show that the FWHM (full width at half maximum) of the diamond crystal increases with an increase in the doping ratio. The XPS results demonstrate that silicon has successfully entered the diamond lattice with a Si–C bond in the crystal. The PL results indicate that the peak intensity of the nitrogen-vacancy (NV−) color center (638 nm) in the synthesized diamond crystal increases as the doping ratio increases. As the SiC doping content increases, the peak of the NV0 color center (575 nm) appears, and the peak intensity increases.
- 14 July 2021
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 23 (35) , 6070-6078
The characteristics of Ib diamond crystals synthesized in a Fe–Ni–C system with different SiC contents
Silicon carbide (SiC) is a substance found in natural diamond inclusions. Analyzing the influence of SiC doping on the properties of synthetic diamonds is vital to understanding the growth mechanism of natural diamonds and the material composition of the mantle. In this work, China-type large volume cubic high-pressure apparatus (CHPA) (SPD-6 × 1200) was used to simulate the high-temperature and high-pressure environment of diamond growth. The influence of different SiC doping contents on the crystal characteristics of a Ib-type diamond synthesized in a Fe–Ni–C system was investigated at a pressure of 5.8 GPa and a temperature range of 1650–1670 K. Optical microscopy (OM), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy (Raman), X-ray photoelectron spectroscopy (XPS), and photoluminescence spectroscopy (PL) were used to characterize the synthesized crystals. The OM results show that the growth rate of the diamond decreases gradually, and the color changes from yellow to light yellow with an increase in the doping concentration. The FTIR results indicate that the nitrogen element in the crystal mainly appears in the diamond crystal in monatomic form (C center). The nitrogen content in the diamond gradually decreases from 275 ppm to 115 ppm with an increase in the SiC dopant ratio. The Raman data show that the FWHM (full width at half maximum) of the diamond crystal increases with an increase in the doping ratio. The XPS results demonstrate that silicon has successfully entered the diamond lattice with a Si–C bond in the crystal. The PL results indicate that the peak intensity of the nitrogen-vacancy (NV−) color center (638 nm) in the synthesized diamond crystal increases as the doping ratio increases. As the SiC doping content increases, the peak of the NV0 color center (575 nm) appears, and the peak intensity increases.