Jong‐Jin Choi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jong‐Jin Choi has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Byung‐Dong Hahn
Department of Future Technology, Korea Institute of Machinery and Materials, Gyeong‐Nam 641‐831, Korea
2 shared publicationsDong‐Soo Park
Department of Future Technology, Korea Institute of Machinery and Materials, Gyeong‐Nam 641‐831, Korea
2 shared publicationsJoo‐Hee Lee
Department of Future Technology, Korea Institute of Machinery and Materials, Gyeong‐Nam 641‐831, Korea
2 shared publicationsWoon‐Ha Yoon
Department of Future Technology, Korea Institute of Machinery and Materials, Gyeong‐Nam 641‐831, Korea
2 shared publicationsByung-Dong Hahn
Korea Institute of Machinery & Materials, Department of Future Technology, Korea, Republic of
1 shared publicationChan Park
Division of Materials Science and Engineering, Pukyong National University, Nam‐Gu, Busan 608‐739, Korea
1 shared publication
Latest Publications
- 2 June 2007
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 90 (6) , 1926-1929
Oxidation Resistance Coating of LSM and LSCF on SOFC Metallic Interconnects by the Aerosol Deposition Process
Conductive La 0.8 Sr 0.2 MnO 3 (LSM) and La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) layers with a thickness of ∼10 μm were deposited on ferritic stainless steel (SS) by the aerosol deposition method, for use as an oxidation resistance‐coating layer in the metallic interconnector of a solid oxide fuel cell. The coated layers were fairly dense without pores or cracks, and maintained good adhesion even after oxidation at 800°C for 100 h. The surface of the bare SS after annealing at 800°C for 100 h was covered with Cr 2 O 3 and Fe 3 O 4 oxide scales, and the electrical conductivity was sharply decreased. However, the LSM‐ and LSCF‐coated SSs showed a surface microstructure with almost no oxidation and maintained good electrical conductivity after annealing at 800°C for 100 h. The area‐specific resistance (ASR) of LSM‐ and LSCF‐coated alloys after 100 h of oxidation at 800°C was 20.6 and 11.7 mΩ·cm 2 , respectively.
- 2 June 2007
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 90 (6) , 1926-1929
Oxidation Resistance Coating of LSM and LSCF on SOFC Metallic Interconnects by the Aerosol Deposition Process
Conductive La 0.8 Sr 0.2 MnO 3 (LSM) and La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) layers with a thickness of ∼10 μm were deposited on ferritic stainless steel (SS) by the aerosol deposition method, for use as an oxidation resistance‐coating layer in the metallic interconnector of a solid oxide fuel cell. The coated layers were fairly dense without pores or cracks, and maintained good adhesion even after oxidation at 800°C for 100 h. The surface of the bare SS after annealing at 800°C for 100 h was covered with Cr 2 O 3 and Fe 3 O 4 oxide scales, and the electrical conductivity was sharply decreased. However, the LSM‐ and LSCF‐coated SSs showed a surface microstructure with almost no oxidation and maintained good electrical conductivity after annealing at 800°C for 100 h. The area‐specific resistance (ASR) of LSM‐ and LSCF‐coated alloys after 100 h of oxidation at 800°C was 20.6 and 11.7 mΩ·cm 2 , respectively.
- 26 January 2007
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 90 (2) , 388-392
Low‐Temperature Sintering of Lead Zinc Niobate–Lead Zirconate Titanate Ceramics Using Nano‐Sized Powder Prepared by the Stirred Media Milling Process
Lead zinc niobate–lead zirconate titanate (PZN–PZT) nano‐sized powders with a diameter of ∼35 nm were fabricated by a high‐energy stirred media mill using 50 μm diameter zirconia beads as the milling media at a rotation speed of 4000 rpm for 1 h. The sintering temperature of PZN–PZT was greatly reduced, and a fully densified bulk body was obtained at only 750°C when stirred media milled nanopowder was used. The control of evaporation of lead oxide was very important to obtain high electrical properties due to the increased surface area of nano‐sized powders. The ferroelectric hysteresis, piezoelectric d 33 coefficient, and dielectric properties of sintered ceramics using nanopowder were measured and compared with the values obtained from a sintered specimen using conventional milled powders. Remanent polarization, d 33 coefficient, and relative dielectric constant of 750°C sintered stirred media milled powders containing 2% of excess PbO and 1% of 4PbO–B 2 O 3 liquid phase were 10.3 μC/cm 2 , 277 pC/N, and 1310, respectively.
- 26 January 2007
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 90 (2) , 388-392
Low‐Temperature Sintering of Lead Zinc Niobate–Lead Zirconate Titanate Ceramics Using Nano‐Sized Powder Prepared by the Stirred Media Milling Process
Lead zinc niobate–lead zirconate titanate (PZN–PZT) nano‐sized powders with a diameter of ∼35 nm were fabricated by a high‐energy stirred media mill using 50 μm diameter zirconia beads as the milling media at a rotation speed of 4000 rpm for 1 h. The sintering temperature of PZN–PZT was greatly reduced, and a fully densified bulk body was obtained at only 750°C when stirred media milled nanopowder was used. The control of evaporation of lead oxide was very important to obtain high electrical properties due to the increased surface area of nano‐sized powders. The ferroelectric hysteresis, piezoelectric d 33 coefficient, and dielectric properties of sintered ceramics using nanopowder were measured and compared with the values obtained from a sintered specimen using conventional milled powders. Remanent polarization, d 33 coefficient, and relative dielectric constant of 750°C sintered stirred media milled powders containing 2% of excess PbO and 1% of 4PbO–B 2 O 3 liquid phase were 10.3 μC/cm 2 , 277 pC/N, and 1310, respectively.
- 1 January 2005
- Published by Springer Nature in MRS Proceedings
- Vol. 902
Deposition of Highly (100) Oriented PZT Film Using Lanthanum Nitrate/Nickel Acetate Buffer Layer
- 1 January 2005
- Published by Springer Nature in MRS Proceedings
- Vol. 902
Deposition of Highly (100) Oriented PZT Film Using Lanthanum Nitrate/Nickel Acetate Buffer Layer