Masanori Kikuchi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Masanori Kikuchi has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Kazuhiro Suga
Tokyo University of Science, 2641 Yamazaki, Noda, Chiba 278-8510, Japan
3 shared publications - Yoshitaka Wada
Kinki University
2 shared publications - Chikako Ohdama
Tokyo University of Science, 2641 Yamazaki, Noda, Chiba 278-8510, Japan
1 shared publication - Fuminori Iwamatsu
Research and Development Group, Hitachi, Ltd., 7-1-1 Omikacho, Hitachi 319-1292, Ibaraki, Japan
1 shared publication - Koichi Minagawa
Graduate School of Tokyo University of Science
1 shared publication Shigeru Aoki
Toyo University
1 shared publication
Latest Publications
- 1 August 2015
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 137 (4) , 041401
Simulation of Stress Corrosion Cracking in In-Core Monitor Housing of Nuclear Power Plant
In the in-core monitor (ICM) housing of a reactor pressure vessel (RPV), residual stress has been widely reported to cause stress corrosion cracking (SCC) damage in the weld heat-affected zone. For this reason, it is important to evaluate the crack growth conservatively, and with high confidence to demonstrate fitness for service. This paper presents crack growth simulations in an ICM housing, which is welded at two different angles to the RPV. One weld angle is at the bottom of the RPV, and the welding area of the ICM housing is axisymmetric. The other angle is at the curved position of the RPV, and the weld area of the ICM housing is asymmetric. In these weld areas, crack growth behavior is estimated by superposed-finite element method (S-FEM), which allows generation of a global finite model and a detailed local mesh representing the crack independently. In the axisymmetric weld area, axial, slant and circumferential surface cracks are assumed at two locations where the residual stress fields are different from each other: one is isotropic and the other is circumferential. It is shown that crack growth behaviors are different under different residual stress fields. The results of S-FEM are compared with those of the influence function method (IFM), which assumes that an elliptical crack shape exists in a plate. It is shown that the IFM result is conservative compared to that of S-FEM. Next, an axial surface crack is assumed at the uphill, downhill, and midhill asymmetric weld areas. The midhill crack growth behavior is different from the uphill and downhill behaviors. Finally, two surface cracks are simulated in the asymmetric weld area and two initial crack arrangements are assumed. These results show the differences of the crack interaction and the crack growth process.
- 1 August 2015
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 137 (4) , 041401
Simulation of Stress Corrosion Cracking in In-Core Monitor Housing of Nuclear Power Plant
In the in-core monitor (ICM) housing of a reactor pressure vessel (RPV), residual stress has been widely reported to cause stress corrosion cracking (SCC) damage in the weld heat-affected zone. For this reason, it is important to evaluate the crack growth conservatively, and with high confidence to demonstrate fitness for service. This paper presents crack growth simulations in an ICM housing, which is welded at two different angles to the RPV. One weld angle is at the bottom of the RPV, and the welding area of the ICM housing is axisymmetric. The other angle is at the curved position of the RPV, and the weld area of the ICM housing is asymmetric. In these weld areas, crack growth behavior is estimated by superposed-finite element method (S-FEM), which allows generation of a global finite model and a detailed local mesh representing the crack independently. In the axisymmetric weld area, axial, slant and circumferential surface cracks are assumed at two locations where the residual stress fields are different from each other: one is isotropic and the other is circumferential. It is shown that crack growth behaviors are different under different residual stress fields. The results of S-FEM are compared with those of the influence function method (IFM), which assumes that an elliptical crack shape exists in a plate. It is shown that the IFM result is conservative compared to that of S-FEM. Next, an axial surface crack is assumed at the uphill, downhill, and midhill asymmetric weld areas. The midhill crack growth behavior is different from the uphill and downhill behaviors. Finally, two surface cracks are simulated in the asymmetric weld area and two initial crack arrangements are assumed. These results show the differences of the crack interaction and the crack growth process.
- 24 August 2012
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 134 (4) , 041009
Effect of KIII on Fatigue Crack Growth Behavior
In this study, mixed-mode fatigue tests are conducted using surface-cracked specimens. Slant surface-cracked specimens are prepared with crack angles of 15 deg, 30 deg, 45 deg, and 60 deg. It is shown that a “factory roof” fracture is formed at the deepest point of the surface crack due to ΔKIII and causes the crack growth rate to decrease. Additionally, fatigue crack growth is simulated using the superposition finite element method (FEM) with crack growth criteria. It is shown that conventional crack growth criteria are not applicable to factory roof fractures. Finally, a modified criterion for the prediction of crack growth rate is proposed, fatigue crack growth simulation is conducted using this criterion, and the results are compared with experimental results.
- 24 August 2012
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 134 (4) , 041009
Effect of KIII on Fatigue Crack Growth Behavior
In this study, mixed-mode fatigue tests are conducted using surface-cracked specimens. Slant surface-cracked specimens are prepared with crack angles of 15 deg, 30 deg, 45 deg, and 60 deg. It is shown that a “factory roof” fracture is formed at the deepest point of the surface crack due to ΔKIII and causes the crack growth rate to decrease. Additionally, fatigue crack growth is simulated using the superposition finite element method (FEM) with crack growth criteria. It is shown that conventional crack growth criteria are not applicable to factory roof fractures. Finally, a modified criterion for the prediction of crack growth rate is proposed, fatigue crack growth simulation is conducted using this criterion, and the results are compared with experimental results.
- 18 May 2012
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 134 (3) , 031205
Simulation of Ductile Fracture of Multiple Flaws
The effect of the interaction of multiple flaws on ductile fracture is studied numerically by Gurson’s constitutive equation. Based on experimental results, two parallel flaw and three parallel flaw problems are simulated. Flaw coalescence does not occur in some problems but does occur in other cases. In all cases, ductile fracture processes are obtained, and the results are compared with the experimental results. The fracture pattern and load-displacement curves agree well with the experimental results. The void growth term is found to be dominant for the coalescence of flaws. The slant flaw problem and the nonuniform length flaw problem are simulated and an evaluation method for the multiple flaws problem is discussed.
- 18 May 2012
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 134 (3) , 031205
Simulation of Ductile Fracture of Multiple Flaws
The effect of the interaction of multiple flaws on ductile fracture is studied numerically by Gurson’s constitutive equation. Based on experimental results, two parallel flaw and three parallel flaw problems are simulated. Flaw coalescence does not occur in some problems but does occur in other cases. In all cases, ductile fracture processes are obtained, and the results are compared with the experimental results. The fracture pattern and load-displacement curves agree well with the experimental results. The void growth term is found to be dominant for the coalescence of flaws. The slant flaw problem and the nonuniform length flaw problem are simulated and an evaluation method for the multiple flaws problem is discussed.
- 1 June 2010
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 10 (1) , 012052
Crack growth simulation for plural crack using hexahedral mesh generation technique
This paper describes a surface crack growth simulation using a new mesh generation technique. The generated mesh is constituted of all hexahedral elements. Hexahedral elements are suitable for an analysis of fracture mechanics parameters, i.e. stress intensity factor. The advantage of a hexahedral mesh is good accuracy of an analysis and less number of degrees of freedoms than a tetrahedral mesh. In this study, a plural crack growth simulation is computed using the hexahedral mesh and its distribution of stress intensity factor is investigated.
- 1 June 2010
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 10 (1) , 012052
Crack growth simulation for plural crack using hexahedral mesh generation technique
This paper describes a surface crack growth simulation using a new mesh generation technique. The generated mesh is constituted of all hexahedral elements. Hexahedral elements are suitable for an analysis of fracture mechanics parameters, i.e. stress intensity factor. The advantage of a hexahedral mesh is good accuracy of an analysis and less number of degrees of freedoms than a tetrahedral mesh. In this study, a plural crack growth simulation is computed using the hexahedral mesh and its distribution of stress intensity factor is investigated.
- Open Access
- 1 January 2003
- Published by Japan Society of Mechanical Engineers in The Abstracts of ATEM : International Conference on Advanced Technology in Experimental Mechanics : Asian Conference on Experimental Mechanics
- Vol. 2003.2, _OS12W0362
OS12W0362 Study on the low cycle fatigue crack growth problem under mode I+II mixed mode condition
The fatigue crack growth test under mode II dominant condition is conducted. It is found that the crack growth direction can not be predicted by the conventional method. By the fracture surface observation, it is also found that the three dimensional effect strongly affects this behavior. Three dimensional elastic-plastic FEM analyses are conducted for this problem considering the Bauschinger effect. The change of the crack tip field during fatigue crack growth is studied. The criteria to predict the fatigue crack growth direction is studied and a new criteria is discussed.
- 1 January 2003
- Published by Japan Society of Mechanical Engineers in The Abstracts of ATEM : International Conference on Advanced Technology in Experimental Mechanics : Asian Conference on Experimental Mechanics
- Vol. 2003.2, _OS12W0362
Open AccessOS12W0362 Study on the low cycle fatigue crack growth problem under mode I+II mixed mode condition
The fatigue crack growth test under mode II dominant condition is conducted. It is found that the crack growth direction can not be predicted by the conventional method. By the fracture surface observation, it is also found that the three dimensional effect strongly affects this behavior. Three dimensional elastic-plastic FEM analyses are conducted for this problem considering the Bauschinger effect. The change of the crack tip field during fatigue crack growth is studied. The criteria to predict the fatigue crack growth direction is studied and a new criteria is discussed.