Zhe Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhe Wu has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Chun‐Mei Yang
College of Mechanical And Electrical Engineering Northeast Forestry University 150040 Harbin China
2 shared publicationsQian‐Jun Liu
College of Mechanical And Electrical Engineering Northeast Forestry University 150040 Harbin China
2 shared publications- Haifeng Jiang
College of Mechanical and Electrical Engineering, Northeast Forestry University, Harbin 150040, China
1 shared publication - Qingnan Wang
College of Mechanical and Electrical Engineering Northeast Forestry University Harbin 150040 P. R. China
1 shared publication - Shuai Zhao
College of Mechanical and Electrical Engineering, Northeast Forestry University, Harbin 150040, China
1 shared publication Yan Ma
College of Mechanical And Electrical Engineering Northeast Forestry University 150040 Harbin China
1 shared publication
Latest Publications
- Open Access
Microstructure Evolution Mechanism of Wf/Cu82Al10Fe4Ni4 Composites under Dynamic Compression at Different Temperatures and Strain Rates
Wf/Cu82Al10Fe4Ni4 composites were fabricated by the pressure infiltration method. The composites were compressed by means of a split Hopkinson pressure bar (SHPB) with strain rates of 800 and 1600 s−1 at different temperatures. The microstructure of the composites after dynamic compressing was analyzed by transmission electron microscopy (TEM). Observation revealed that there were high-density dislocations, stacking faults, twins, and recrystallization existing in the copper alloy matrix of the composites. High-density dislocations, stacking faults, and twins were generated due to the significant plastic deformation of the copper alloy matrix under dynamic load impact. We also found that the precipitated phase of the matrix played a role in the second phase strengthening; recrystallized microstructures of copper alloy were generated due to dynamic recrystallization of the copper alloy matrix under dynamic compression at high temperatures.
Open AccessMicrostructure Evolution Mechanism of Wf/Cu82Al10Fe4Ni4 Composites under Dynamic Compression at Different Temperatures and Strain Rates
Wf/Cu82Al10Fe4Ni4 composites were fabricated by the pressure infiltration method. The composites were compressed by means of a split Hopkinson pressure bar (SHPB) with strain rates of 800 and 1600 s−1 at different temperatures. The microstructure of the composites after dynamic compressing was analyzed by transmission electron microscopy (TEM). Observation revealed that there were high-density dislocations, stacking faults, twins, and recrystallization existing in the copper alloy matrix of the composites. High-density dislocations, stacking faults, and twins were generated due to the significant plastic deformation of the copper alloy matrix under dynamic load impact. We also found that the precipitated phase of the matrix played a role in the second phase strengthening; recrystallized microstructures of copper alloy were generated due to dynamic recrystallization of the copper alloy matrix under dynamic compression at high temperatures.
- 28 June 2014
- Published by Wiley in Rare Metals
- Vol. 33 (4) , 414-418
Mechanical properties of tungsten heavy alloy and damage behaviors after hypervelocity impact
93W‐4.5Ni‐1.5Fe‐1Co (W) was prepared by powder metallurgic method, and then dynamic mechanical properties of this material were tested at high temperature by means of high‐temperature split Hopkinson pressure bar (SHPB). The results show that the material possesses high‐dynamic mechanical properties, significant temperature effects, and strain hardening behaviors. Used two‐stage light gas gun, the penetration test of 93W projectile was finished. After the completion of the test, through the microstructure observation of the residual 93W projectiles with the aid of scanning electron microscopy (SEM) and transmission electron microscopy (TEM), it can be found that there are obvious signs of hot melt existing on the surface of the projectile, a lot of adiabatic shear bands inside the projectile, and microcracks exist at the end of adiabatic shear bands. The test results show that adiabatic shear is the main form to cause the projectile failure and it is the emergence of the adiabatic shearing phenomenon that makes 93W display good self‐sharpening property in the process of hypervelocity penetration. At the same time, the results of TEM observation show that there are high‐density dislocations at the interface between W and Ni–Fe–Co‐based alloy inside the 93W.
- 28 June 2014
- Published by Wiley in Rare Metals
- Vol. 33 (4) , 414-418
Mechanical properties of tungsten heavy alloy and damage behaviors after hypervelocity impact
93W‐4.5Ni‐1.5Fe‐1Co (W) was prepared by powder metallurgic method, and then dynamic mechanical properties of this material were tested at high temperature by means of high‐temperature split Hopkinson pressure bar (SHPB). The results show that the material possesses high‐dynamic mechanical properties, significant temperature effects, and strain hardening behaviors. Used two‐stage light gas gun, the penetration test of 93W projectile was finished. After the completion of the test, through the microstructure observation of the residual 93W projectiles with the aid of scanning electron microscopy (SEM) and transmission electron microscopy (TEM), it can be found that there are obvious signs of hot melt existing on the surface of the projectile, a lot of adiabatic shear bands inside the projectile, and microcracks exist at the end of adiabatic shear bands. The test results show that adiabatic shear is the main form to cause the projectile failure and it is the emergence of the adiabatic shearing phenomenon that makes 93W display good self‐sharpening property in the process of hypervelocity penetration. At the same time, the results of TEM observation show that there are high‐density dislocations at the interface between W and Ni–Fe–Co‐based alloy inside the 93W.
- 31 May 2014
- Published by Wiley in Rare Metals
- Vol. 33 (3) , 330-336
Damage behavior of tungsten fiber‐reinforced copper matrix composite after high‐speed impact
W f /Cu 82 Al 10 Fe 4 Ni 4 composite was fabricated by means of infiltration casting. By the microstructure observation of the composite with the aid of scanning electron microscopy (SEM) and transmission electron microscopy (TEM), it can be found that there are (Fe, Ni), AlFe, Al 3 Ni, and Cu 3 Al precipitated phases existing in the matrix alloy. By two‐stage light gas gun, W f /Cu 82 Al 10 Fe 4 Ni 4 composite hypervelocity projectile into concrete target test with the speed of 2.2 km·s −1 is finished. By microstructure observation, it can be found that the failure mode of W f /Cu 82 Al 10 Fe 4 Ni 4 composite projectile during penetration is the rapid peeling of tungsten fibers from the projectile, which makes the projectile display good self‐sharpening property. Meanwhile, it can be found that microstructure morphology change of W f /Cu 82 Al 10 Fe 4 Ni 4 composite occurs after hypervelocity impact. The density of dislocations around the large‐dimensional (Fe, Ni), AlFe, Al 3 Ni, and Cu 3 Al precipitated phases in the matrix alloy rises sharply. At the same time, there are large‐dimensional deformed twins existing in local regions and stacking faults existing inside the twins.
- 31 May 2014
- Published by Wiley in Rare Metals
- Vol. 33 (3) , 330-336
Damage behavior of tungsten fiber‐reinforced copper matrix composite after high‐speed impact
W f /Cu 82 Al 10 Fe 4 Ni 4 composite was fabricated by means of infiltration casting. By the microstructure observation of the composite with the aid of scanning electron microscopy (SEM) and transmission electron microscopy (TEM), it can be found that there are (Fe, Ni), AlFe, Al 3 Ni, and Cu 3 Al precipitated phases existing in the matrix alloy. By two‐stage light gas gun, W f /Cu 82 Al 10 Fe 4 Ni 4 composite hypervelocity projectile into concrete target test with the speed of 2.2 km·s −1 is finished. By microstructure observation, it can be found that the failure mode of W f /Cu 82 Al 10 Fe 4 Ni 4 composite projectile during penetration is the rapid peeling of tungsten fibers from the projectile, which makes the projectile display good self‐sharpening property. Meanwhile, it can be found that microstructure morphology change of W f /Cu 82 Al 10 Fe 4 Ni 4 composite occurs after hypervelocity impact. The density of dislocations around the large‐dimensional (Fe, Ni), AlFe, Al 3 Ni, and Cu 3 Al precipitated phases in the matrix alloy rises sharply. At the same time, there are large‐dimensional deformed twins existing in local regions and stacking faults existing inside the twins.