Lu Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Lu Lin has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
Sai He
Metallurgical Technology Research Institute, Central Iron and Steel Research Institute, Beijing 100081, China
5 shared publicationsWei Wu
Metallurgical Technology Research Institute, Central Iron and Steel Research Institute Co., Ltd., Beijing, China
4 shared publicationsYa-Qin Liu
Metallurgical Technology Research Institute, Central Iron and Steel Research Institute, Beijing 100081, China
4 shared publicationsYan-Ping Bao
State Key Laboratory of Advanced Metallurgy , University of Science and Technology Beijing , Beijing 100083 , China
4 shared publicationsZhong-Xiao Hou
Metallurgical Technology Research Institute, Central Iron and Steel Research Institute, Beijing 100081, China
4 shared publicationsYan Lv
Metallurgical Technology Research Institute, Central Iron and Steel Research Institute, Beijing 100081, China
3 shared publications
Latest Publications
- 1 October 2026
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 33 (10) , 3437-3447
Management and technical challenges of laminar flow-dedicated line production in steel manufacturing
- 1 October 2026
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 33 (10) , 3437-3447
Management and technical challenges of laminar flow-dedicated line production in steel manufacturing
- 27 April 2023
- Published by EDP Sciences in Metallurgical Research & Technology
- Vol. 120 (3) , 307
Study on the recovery of phosphorus and iron from molten modified high-phosphorus industrial slag by carbothermal reduction
To effectively recycle phosphorus and iron resources in high-phosphorus industrial slag during molten modification process, the thermodynamic conditions and influence laws of recovery of valuable elements from converter slag with different P2O5 content by carbothermal reduction after melting and modification are systematically analyzed. The results show that the reduction rates of P2O5 and FeO decrease with the increase of P2O5 content at 1450 °C and the basicity of 1.0. Meanwhile, the experimental results prove that the reduction of FeO precedes the reduction of P2O5.The phosphorus element in initial industrial slag mainly exists in the form of Ca5(PO4)2SiO4 and increases with the increase of P2O5 content. With the progress of the carbothermal reduction reaction, the Ca5(PO4)2SiO4 content in experimental slags after reduction decrease significantly. The iron element in initial industrial slag mainly exists in the form of FeO, (MgO)0.239 (FeO)0.761 and Ca2Fe2O5 and disappear after carbothermic reduction reaction. In the range of P2O5 content of 4–8 wt.%, P2O5 content has little effect on the thermodynamic trend of the formation of phosphorus-containing phase Ca5(PO4)2SiO4, but it is not good for the thermodynamic trend of gasification dephosphorization reaction in the carbothermic reduction process. Therefore, the increase of P2O5 content is not conducive to the occurrence of carbothermic reduction gasification dephosphorization reaction.
- 27 April 2023
- Published by EDP Sciences in Metallurgical Research & Technology
- Vol. 120 (3) , 307
Study on the recovery of phosphorus and iron from molten modified high-phosphorus industrial slag by carbothermal reduction
To effectively recycle phosphorus and iron resources in high-phosphorus industrial slag during molten modification process, the thermodynamic conditions and influence laws of recovery of valuable elements from converter slag with different P2O5 content by carbothermal reduction after melting and modification are systematically analyzed. The results show that the reduction rates of P2O5 and FeO decrease with the increase of P2O5 content at 1450 °C and the basicity of 1.0. Meanwhile, the experimental results prove that the reduction of FeO precedes the reduction of P2O5.The phosphorus element in initial industrial slag mainly exists in the form of Ca5(PO4)2SiO4 and increases with the increase of P2O5 content. With the progress of the carbothermal reduction reaction, the Ca5(PO4)2SiO4 content in experimental slags after reduction decrease significantly. The iron element in initial industrial slag mainly exists in the form of FeO, (MgO)0.239 (FeO)0.761 and Ca2Fe2O5 and disappear after carbothermic reduction reaction. In the range of P2O5 content of 4–8 wt.%, P2O5 content has little effect on the thermodynamic trend of the formation of phosphorus-containing phase Ca5(PO4)2SiO4, but it is not good for the thermodynamic trend of gasification dephosphorization reaction in the carbothermic reduction process. Therefore, the increase of P2O5 content is not conducive to the occurrence of carbothermic reduction gasification dephosphorization reaction.
- 4 February 2023
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 30 (4) , 697-707
Influence of temperature and Fe2O3 on phosphorus recovery from dephosphorization slag by reduction
- 4 February 2023
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 30 (4) , 697-707
Influence of temperature and Fe2O3 on phosphorus recovery from dephosphorization slag by reduction
- 25 September 2022
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 50 (4) , 350-359
Effect of slag basicity and reduction time on carbothermal reduction behaviour of P-bearing steelmaking slag
To realize the efficient reduction and recycling of phosphorus resources in P-bearing steelmaking slag, it is necessary to study slag composition and phase changes during carbothermal reduction under different conditions (slag basicity and reduction time). The thermodynamic and kinetic behaviours of carbothermal reduction dephosphorization of P-bearing steelmaking slag are systematically discussed as well. The results show that the reduction rate of FeO and P2O5 show an upward trend with the increase of reduction time at 1823 K. However, the reduction rate of FeO does not change much within 50 minutes. In the range of slag basicity from 0.5 to 2.5, the formation of Ca3(PO4)2 increases with the increase of slag basicity. However, the increase of slag basicity is not good for the occurrence of carbothermic reduction gasification dephosphorization reaction. Taking into account the higher formation of Ca3(PO4)2 and the better dephosphorization effect of carbothermic reduction gasification, the appropriate slag basicity for carbothermic reduction gasification dephosphorization is 1.0–1.5. Carbothermal reduction gasification dephosphorization reaction of P-bearing steelmaking slag is a second-order reaction, and the mass transfer of P2O5 in the slag is the rate-limiting step of the whole process. The kinetic equations that describe the variation of P2O5 content in slag with time are yielded through regression. At 1823 K, by controlling the appropriate slag basicity (1.0–1.5) and reduction time (at least 20 minutes), the gasification dephosphorization rate of the carbothermal reduction can reach more than 80%, which can realize efficient recovery of phosphorus resources in P-bearing steelmaking slag.
- 25 September 2022
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 50 (4) , 350-359
Effect of slag basicity and reduction time on carbothermal reduction behaviour of P-bearing steelmaking slag
To realize the efficient reduction and recycling of phosphorus resources in P-bearing steelmaking slag, it is necessary to study slag composition and phase changes during carbothermal reduction under different conditions (slag basicity and reduction time). The thermodynamic and kinetic behaviours of carbothermal reduction dephosphorization of P-bearing steelmaking slag are systematically discussed as well. The results show that the reduction rate of FeO and P2O5 show an upward trend with the increase of reduction time at 1823 K. However, the reduction rate of FeO does not change much within 50 minutes. In the range of slag basicity from 0.5 to 2.5, the formation of Ca3(PO4)2 increases with the increase of slag basicity. However, the increase of slag basicity is not good for the occurrence of carbothermic reduction gasification dephosphorization reaction. Taking into account the higher formation of Ca3(PO4)2 and the better dephosphorization effect of carbothermic reduction gasification, the appropriate slag basicity for carbothermic reduction gasification dephosphorization is 1.0–1.5. Carbothermal reduction gasification dephosphorization reaction of P-bearing steelmaking slag is a second-order reaction, and the mass transfer of P2O5 in the slag is the rate-limiting step of the whole process. The kinetic equations that describe the variation of P2O5 content in slag with time are yielded through regression. At 1823 K, by controlling the appropriate slag basicity (1.0–1.5) and reduction time (at least 20 minutes), the gasification dephosphorization rate of the carbothermal reduction can reach more than 80%, which can realize efficient recovery of phosphorus resources in P-bearing steelmaking slag.
- Open Access
- 26 May 2022
- Published by MDPI AG in Inorganics
- Vol. 10 (6) , 70
Carbonaceous FexP Synthesized via Carbothermic Reduction of Dephosphorization Slag as Hydrogen Evolution Catalyst for Water Splitting
Developing the high-efficiency and cheap non-noble catalysts towards hydrogen evolution reaction (HER) is of significance for water splitting. Herein, for the first time, we report a simple method of acid leaching combined with carbothermic reduction with dephosphorization slag to construct a carbonaceous FexP/C catalyst. In alkaline medium, the corresponding overpotential when the output current density was 10 mA cm−2 (η10) was only 145 mV. Additionally, there was no obvious attenuation after 3000 cycles, which showed significantly better activity and stability than that of non-carbonaceous FexP catalysts prepared by gas–solid phosphating. The structure and composition of FexP/C were characterized by X-ray diffraction, scanning electron microscope, energy dispersive spectroscopy, and inductively coupled plasma atomic emission spectrometer. The electrochemical properties of the electrode were evaluated by cyclic voltammetry, linear scanning voltammetry, electrochemical impedance spectroscopy, and cyclic stability. The results showed that the prepared FexP/C was composed of FeP-Fe2P mixed nanocrystals supported on amorphous carbon. Compared with FexP, the synergistic catalysis of the FeP and Fe2P phases as well as the interactive support effect between the FeP-Fe2P mixed nanocrystals and the amorphous carbon support will attribute the rich active sites for electrocatalytic reaction and reduce the charge transfer resistance. Thus, FexP/C has good hydrogen evolution activity and stability. Overall, the preparation of catalysts with high additional value based on dephosphorization slag was preliminarily explored.
- 26 May 2022
- Published by MDPI AG in Inorganics
- Vol. 10 (6) , 70
Open AccessCarbonaceous FexP Synthesized via Carbothermic Reduction of Dephosphorization Slag as Hydrogen Evolution Catalyst for Water Splitting
Developing the high-efficiency and cheap non-noble catalysts towards hydrogen evolution reaction (HER) is of significance for water splitting. Herein, for the first time, we report a simple method of acid leaching combined with carbothermic reduction with dephosphorization slag to construct a carbonaceous FexP/C catalyst. In alkaline medium, the corresponding overpotential when the output current density was 10 mA cm−2 (η10) was only 145 mV. Additionally, there was no obvious attenuation after 3000 cycles, which showed significantly better activity and stability than that of non-carbonaceous FexP catalysts prepared by gas–solid phosphating. The structure and composition of FexP/C were characterized by X-ray diffraction, scanning electron microscope, energy dispersive spectroscopy, and inductively coupled plasma atomic emission spectrometer. The electrochemical properties of the electrode were evaluated by cyclic voltammetry, linear scanning voltammetry, electrochemical impedance spectroscopy, and cyclic stability. The results showed that the prepared FexP/C was composed of FeP-Fe2P mixed nanocrystals supported on amorphous carbon. Compared with FexP, the synergistic catalysis of the FeP and Fe2P phases as well as the interactive support effect between the FeP-Fe2P mixed nanocrystals and the amorphous carbon support will attribute the rich active sites for electrocatalytic reaction and reduce the charge transfer resistance. Thus, FexP/C has good hydrogen evolution activity and stability. Overall, the preparation of catalysts with high additional value based on dephosphorization slag was preliminarily explored.
- Open Access
- 1 January 2022
- Published by Walter de Gruyter GmbH in High Temperature Materials and Processes
- Vol. 41 (1) , 578-588
Experimental study on the preparation of ferrophosphorus alloy using dephosphorization furnace slag by carbothermic reduction
With the development of the duplex converter process, the amount of dephosphorization furnace slag is increasing, and it has relatively low basicity. It has been indicated that the recovery of valuable elements from dephosphorization slag by carbothermic reduction has great environmental and economic benefits due to its high content of P, Fe, and Mn. In this work, the experimental slag was reduced by carbon powder in a resistance furnace at 1,550°C. The results show that 76.82% of P, 99.60% of Fe, and 11.82% of Mn in the slag are recycled at basicity 1.0, and the recovery ratios of P, Fe, and Mn are 34.58, 78.89, and 13.85% at basicity 2.0, respectively. The ferrophosphorus obtained from the reduction of the dephosphorization furnace slag can be used as a raw material for steel-making alloy, and the residual steel slag can be used as cement and other building materials. This work provides a reference for recycling and resource utilization of dephosphorization furnace slag.
- 1 January 2022
- Published by Walter de Gruyter GmbH in High Temperature Materials and Processes
- Vol. 41 (1) , 578-588
Open AccessExperimental study on the preparation of ferrophosphorus alloy using dephosphorization furnace slag by carbothermic reduction
With the development of the duplex converter process, the amount of dephosphorization furnace slag is increasing, and it has relatively low basicity. It has been indicated that the recovery of valuable elements from dephosphorization slag by carbothermic reduction has great environmental and economic benefits due to its high content of P, Fe, and Mn. In this work, the experimental slag was reduced by carbon powder in a resistance furnace at 1,550°C. The results show that 76.82% of P, 99.60% of Fe, and 11.82% of Mn in the slag are recycled at basicity 1.0, and the recovery ratios of P, Fe, and Mn are 34.58, 78.89, and 13.85% at basicity 2.0, respectively. The ferrophosphorus obtained from the reduction of the dephosphorization furnace slag can be used as a raw material for steel-making alloy, and the residual steel slag can be used as cement and other building materials. This work provides a reference for recycling and resource utilization of dephosphorization furnace slag.
- 10 August 2021
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 28 (8) , 1264-1273
Consideration of green intelligent steel processes and narrow window stability control technology on steel quality
- 10 August 2021
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 28 (8) , 1264-1273
Consideration of green intelligent steel processes and narrow window stability control technology on steel quality
- 22 June 2020
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 48 (3) , 334-342
Influence of slag temperature on phosphorus enrichment in P-bearing steelmaking slag
To effectively recycle the phosphorus in P-bearing steelmaking slag and use it as slag phosphate fertilizer, it is necessary to study the effect of slag temperature on occurrence forms and enrichment behaviour of phosphorus in P-bearing steelmaking slag. In this work, the thermodynamic and kinetic behaviours of the formation of phosphorus-rich phases are systematically investigated. The results show that decreasing of the slag temperature (1473—1823 K) has a little effect on the thermodynamic trend of the formation of the 2CaO·SiO2 phase (denoted as C2S) and on the early precipitation of the n2CaO·SiO2–3CaO·P2O5 solid solution (denoted as n C2S–C3P). Additionally, the precipitation of C2S first increases and then decreases, and reaches a maximum value between 1623 and 1653 K. Moreover, the diffusion of phosphorus is a rate-limiting link in the process. The kinetic equation that describes the variation of P2O5 content with time in the phosphorus-rich phase is . The composition of the P-bearing steelmaking slag is in the dicalcium silicate (C2S) primary zone. Controlling the hold temperature and time, and the cooling rate of the P-bearing slag, allows for high-concentration phosphorus enrichment and for the increase of particle size in the n C2S–C3P solid solution. Also, when controlling the aforementioned parameters, the phosphorus partition ratio between the phosphorus-rich and matrix phases (L p’) increases from 1.1–1.5 to 60–130, and the morphology of the former changes from acicular to fine bar to roughing bar. Furthermore, the P2O5 content in phosphorus-rich phase is 31%–33% in enriched slag, meeting the requirements for phosphate fertilizer production.- 22 June 2020
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 48 (3) , 334-342
Influence of slag temperature on phosphorus enrichment in P-bearing steelmaking slag
To effectively recycle the phosphorus in P-bearing steelmaking slag and use it as slag phosphate fertilizer, it is necessary to study the effect of slag temperature on occurrence forms and enrichment behaviour of phosphorus in P-bearing steelmaking slag. In this work, the thermodynamic and kinetic behaviours of the formation of phosphorus-rich phases are systematically investigated. The results show that decreasing of the slag temperature (1473—1823 K) has a little effect on the thermodynamic trend of the formation of the 2CaO·SiO2 phase (denoted as C2S) and on the early precipitation of the n2CaO·SiO2–3CaO·P2O5 solid solution (denoted as n C2S–C3P). Additionally, the precipitation of C2S first increases and then decreases, and reaches a maximum value between 1623 and 1653 K. Moreover, the diffusion of phosphorus is a rate-limiting link in the process. The kinetic equation that describes the variation of P2O5 content with time in the phosphorus-rich phase is . The composition of the P-bearing steelmaking slag is in the dicalcium silicate (C2S) primary zone. Controlling the hold temperature and time, and the cooling rate of the P-bearing slag, allows for high-concentration phosphorus enrichment and for the increase of particle size in the n C2S–C3P solid solution. Also, when controlling the aforementioned parameters, the phosphorus partition ratio between the phosphorus-rich and matrix phases (L p’) increases from 1.1–1.5 to 60–130, and the morphology of the former changes from acicular to fine bar to roughing bar. Furthermore, the P2O5 content in phosphorus-rich phase is 31%–33% in enriched slag, meeting the requirements for phosphate fertilizer production.- 27 February 2020
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 27 (3) , 282-294
Reaction kinetics during direct alloying of manganese ore cored wire
- 27 February 2020
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 27 (3) , 282-294
Reaction kinetics during direct alloying of manganese ore cored wire
- Open Access
- 8 June 2018
- Published by Walter de Gruyter GmbH in High Temperature Materials and Processes
- Vol. 37 (8) , 741-747
Manganese Ore Decomposition and Carbon Reduction in Steelmaking
To improve the direct alloying of manganese ore in steelmaking, the decomposition and carbon reduction of manganese ore was studied using a differential thermal analyzer and resistance furnace. The remaining material after manganese ore decomposition at 1,600 °C was a mixture of 43 % MnO, 40 % MnSiO 3 and FeO, and 17 % MnSiO 3 . The remaining material after the carbon reduction of the manganese ore was a mixture of metal (30.8 % Mn 7 C 3 and 16.1 % FeC 3 ) and slag (2.5 % FeO, 5.1 % SiO 2 , and 18.8 % MnO). The high-temperature (1,200 ℃) decomposition and reduction of manganese ore produce manganese carbonate, manganese dioxide, and manganese salicylate sesquioxide. However, because it is not easy to decompose the manganese silicate in the manganese ore, the proportion of ore being reduced by carbon is small. Therefore, the increase of the manganese reduction of manganese silicate is critical to the direct alloying of manganese ore. Adding calcium oxide or magnesium oxide to the manganese ore improves the reduction of manganese ore, whereas adding slag from the initial stage or endpoint of the converter process has little effect on the manganese ore reduction.
- 8 June 2018
- Published by Walter de Gruyter GmbH in High Temperature Materials and Processes
- Vol. 37 (8) , 741-747
Open AccessManganese Ore Decomposition and Carbon Reduction in Steelmaking
To improve the direct alloying of manganese ore in steelmaking, the decomposition and carbon reduction of manganese ore was studied using a differential thermal analyzer and resistance furnace. The remaining material after manganese ore decomposition at 1,600 °C was a mixture of 43 % MnO, 40 % MnSiO 3 and FeO, and 17 % MnSiO 3 . The remaining material after the carbon reduction of the manganese ore was a mixture of metal (30.8 % Mn 7 C 3 and 16.1 % FeC 3 ) and slag (2.5 % FeO, 5.1 % SiO 2 , and 18.8 % MnO). The high-temperature (1,200 ℃) decomposition and reduction of manganese ore produce manganese carbonate, manganese dioxide, and manganese salicylate sesquioxide. However, because it is not easy to decompose the manganese silicate in the manganese ore, the proportion of ore being reduced by carbon is small. Therefore, the increase of the manganese reduction of manganese silicate is critical to the direct alloying of manganese ore. Adding calcium oxide or magnesium oxide to the manganese ore improves the reduction of manganese ore, whereas adding slag from the initial stage or endpoint of the converter process has little effect on the manganese ore reduction.