Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Peng Wu has a total of 108 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Vibration Power Flow Modeling and Experimental Verification of a Multi-Substructure Centrifugal Pump Prototype

    by Fabao Yang, Xinxiang He, Xiaoyong Yu, Shuowen Wang, Shuaijun Li, Peng Wu, Dazhuan Wu

    To enable consistent modeling and quantitative evaluation of vibration-energy transmission in centrifugal pumps with multiple coupled substructures and branches, this study develops a generalized transfer-matrix model. The method combines Craig-Bampton reduction with the four-terminal parameter method and the multibody system transfer matrix method. Dynamic-equilibrium and kinematic-compatibility constraints are incorporated at branch nodes so that chain-like and branched paths can be assembled within one formulation. A vibration-power-flow model was developed for three layouts of a prototype comprising an equivalent pump body, an extended casing, spring–damper connectors, and a support base. Its predictions of axial active power flow at the L6 mounting-foot connection were compared with measurements over 8–1000 Hz. The mean relative error for the first 12 natural frequencies was 4.38%. The power-flow-level RMSEs for Layouts 1–3 were 3.12, 2.71, and 2.28 dB, respectively, and the highest proportion of frequency points within a ±3 dB deviation band was 91.4%. The three layouts exhibited similar power-flow trends over approximately 8–80 Hz, whereas differences in amplitude and peak–valley locations became pronounced above 250 Hz as energy was redistributed among parallel paths. The proposed framework provides a quantitative basis for comparing centrifugal-pump layouts and controlling vibration-transmission paths.

  • Open Access

    Analysis of dynamic and stability behavior of multi-groove water-lubricated bearings

    by Zhidong Wu, Huimeng Jiang, Kang Zhou, Peng Wu, Dazhuan Wu

    The instability of journal bearings limits their application in high-speed rotating machinery. This paper examines the dynamic response and stability of a rotor supported by multi-groove water-lubricated journal bearings. A computational fluid dynamics model is developed for the bearing clearance, and journal motion is introduced through a user-defined dynamic-mesh procedure. The stiffness and damping coefficients are extracted using the different-frequency disturbance method. The effects of groove profile, groove arrangement, groove angle and load angle are compared under different Sommerfeld numbers. The results reveal how groove geometric parameters affect shaft stability under different operating conditions. The numerical predictions agree with the experimental observations, indicating that the proposed method can support the design and parameter selection of water-lubricated bearings.

  • Research on a rapid evaluation method for unsteady pressure pulsations in centrifugal pumps based on a steady flow field

    by Xinxiang He, Xin Yang, Zhiwei Sun, Bin Huang, Shuai Yang, Peng Wu, Dazhuan Wu

    The evaluation of unsteady pressure pulsations in centrifugal pumps usually relies on unsteady numerical simulations or experiments, which are time-consuming and costly. As centrifugal pumps are key components in energy systems, their pressure pulsation characteristics are critical to the stable operation of the system. Consequently, there is an urgent need for a rapid and cost-effective evaluation method. This study explores the correlation between the steady flow field structure and unsteady pressure pulsations. The steady flow field structure and the unsteady pressure pulsations for different numbers of blades are analyzed, and a rapid and cost-effective evaluation method for the unsteady pressure pulsations based on the spatial Fourier transform of the steady flow field structure is proposed. Correlation analysis between the steady-state indicator Ste obtained from the spatial spectrum and the averaged blade passing frequency peak pressure-pulsation coefficient c¯p shows that the spatial frequency corresponding to the maximum amplitude represents the number of impeller blades, while the amplitude at this frequency quantifies the pressure pulsation at the blade passing frequency. Finally, the effectiveness of the proposed method is validated using two sets of representative cases. By summarizing all datasets, the correlation coefficient between Ste and c¯p at the blade passing frequency reaches 0.9538. These results validate the reliability of the proposed evaluation method, thereby enabling rapid iterative improvement of pumps and promoting their sustainable operation.


  • Comparison Analysis on the Hydraulic Performance and Flow Characteristics on a Reactor Coolant Pump Under Rated Operating Condition Between Lead–Bismuth Eutectic and Water Mediums

    by Shangxiang Lu, Huimeng Jiang, Peng Wu, Bin Huang, Dazhuan Wu

    Advanced Generation IV nuclear reactors aim to enhance the sustainability, passive safety, reliability, and economic efficiency of reactor operations. Within that, the reactor coolant pump is a critical component in the reactor's cooling system, due to the unique characteristics of the transported medium, posing challenges for engineering applications. This study focuses on a mixed-flow nuclear reactor coolant pump, indicating that significant differences in hydraulic performance and flow characteristics arise due to the varying flow Reynolds numbers under identical operating conditions for the two mediums. Research employing quantitative analysis of boundary layer friction losses and flow separation-induced flow blockage elucidates the origins of hydraulic performance differences. Subsequent studies focusing on the flow characteristics within the impeller reveal that, while the flow patterns inside the impeller show no fundamental differences, an increase in Reynolds number intensifies flow slippage phenomenon, partially diminishing the impeller's work capability. Analysis in static components indicates that the stronger centrifugal forces lead to increased nonuniformity in flow distribution within the guide vanes and an amplified wake phenomenon within the outlet pipe.


  • Numerical simulation of turbulent Taylor–Couette flow with high Taylor number and large radius ratio in high-speed canned motor pump internals

    by Yuhan Zhang, Rui Xu, Yuchen Song, Dazhuan Wu, Peng Wu

    Taylor–Couette flow with a high Taylor number and large radius ratio is widely present in fluid machinery, such as the internal clearance flow in a canned motor pump typically. Taylor–Couette flow with radius ratios from 0.934 to 0.977 and Taylor number from 107 to 1010 was investigated by numerical simulations. The results indicated that torque is positively correlated to radius ratio, while dimensionless torque is exponentially related to the Taylor number. Subsequently, the physical characteristics of the flow field were described by extracting statistical quantities such as the average azimuthal velocity profile, velocity fluctuations, and near-wall region analysis at four internal cylinder rotation frequencies and four radius ratios. The results revealed that increasing rotation frequency would increase velocity gradients near the wall, while higher radius ratios would produce more uniform velocity fluctuation distributions. In addition, near-wall profiles showed a constant shear force layer, while the logarithmic layer was affected by rotation frequency and radius ratio. The detailed analysis revealed that as the rotation frequency increased, the flow gradually transitioned to a turbulent state, intensifying the interaction between large and small vortex structures. The rotation speeds of Taylor vortices remained consistent across different radius ratios, with smaller scales and more numerous vortices observed at larger ratios. Smaller radius ratios led to more fine-scale vortex structures near the cylindrical wall, significantly impacting azimuthal velocity fluctuations. Finally, near-wall velocity streaks are presented to demonstrate their periodic nature and the relationship between high-speed and low-speed regions, as well as their interaction with the wall and changes with distance.


  • Influence of the channel inclination on the exchange flow and vorticity transport characteristics in a regenerative flow pump

    by Qianqian Li, Xiao Lou, Deli Tang, Guoshou Zhao, Fengfeng Bie, Yi Lu, Peng Wu

    To enhance the overall performance of regenerative flow pump (RFP) to achieve efficient and stable operation over a broad range, this paper employs numerical simulation to study the internal flow conditions of RFP models with three different inclination coefficients (Ic = −0.25, Ic = 0, Ic = 0.25). The analysis focuses on the pressure distribution, energy exchange, velocity variation, and vorticity distribution characteristics within the impeller and channel. The comparison indicates that at Ic = −0.25 with an outward channel, the flow within the pump is stabilized, and the rate of pressure growth and exchange intensity are increased. When Ic = 0 with a semi-circular channel and Ic = 0.25 with an inward channel, there are narrower flow space at the channel's outer diameter, impeding effective fluid motion along the channel and inducing chaotic flow. This condition escalates flow losses and adversely affects the hydraulic performance of the RFP. Additionally, the analysis based on the vorticity transport equation reveals that the Coriolis force term significantly contributes to the generation and transport of vortex in the impeller, while the vortex stretching term dominates the transport of vortex in the channel.


  • Open Access

    Investigation of the unsteady pressure fluctuation mechanism in a regenerative flow pump based on proper orthogonal decomposition

    by Qianqian Li, Deli Tang, Xiao Lou, Guoshou Zhao, Peng Wu, Fengfeng Bie, Yi Lu

    The regenerative flow pump (RFP) derives its name from the circular flow pattern akin to a vortex. However, the presence of numerous vortices results in highly turbulent flow and pressure fluctuation. This study delves into the characteristics of the internal unsteady flow in two distinct RFP models featuring different blade shapes. Numerical simulations are employed to obtain the pressure field, which is subsequently scrutinized using the proper orthogonal decomposition (POD) method. The results show that the average pressure in the peripheral direction undergoes minimal variation during the flow developing stage, experiences a sharp increase in the fully developed stage, and finally exhibits substantial changes in the stripper. The transient pressure in the time domain fluctuates periodically, and the dominant blade passing frequency in the frequency domain demonstrates a similar trend along the circumferential direction as the average pressure. Moreover, the fluctuating intensity of pressure diminishes along the impeller's rotating direction but intensifies significantly in the stripper. Comparative analysis indicates that the exchange intensity is influenced by the flow at different developmental stages, and the exchange flow conditions could reflect the fluctuating intensity. Furthermore, the study reveals that the frequency amplitude of the time coefficient gradually decreases as the mode order increases. The first and second modes exhibit a gradually changing trend associated with pressure increase patterns, whereas the third and fourth modes highlight the emergence of localized modulation phenomena linked to exchange flow. Thus, the POD method offers a unique perspective for comprehending the flow mechanisms within RFPs.