YLYu-Wen Liu

Yu-Wen Liu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yu-Wen Liu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:

  • Shih-Wei Cho

    Department of Civil Engineering and Engineering Management, National Quemoy University, Kinmen (Taiwan)

    2 shared publications
  • An-Shun Cheng

    National Chung-Hsing University in Taiwan

    1 shared publication
  • Jenq-Chuan Liou

    Department of Civil and Water Resources Engineering, National Chia Yi University, Chia-Yi 600, Taiwan

    1 shared publication
  • Kun-Sheng Pann

    Department of Civil Engineering , Cheng Shiu University , Kaoshiung, Taiwan

    1 shared publication
  • Pou-Gang Chiou

    Department of Civil and Water Resources Engineering, National Chiayi University, Chiayi (Taiwan)

    1 shared publication
  • Tsao-Hua Hsu

    Department of Civil and Water Resources Engineering, National Chia Yi University, Chia-Yi 600, Taiwan

    1 shared publication

Latest Publications

  • Open Access

    Effect of waste oyster shell powder as additive on properties and sulfate attack resistance of mortar

    by Yu-Wen Liu, Shih-Wei Cho, Pou-Gang Chiou

    In this study, the waste oyster shell powder was added in mix design to investigate the properties, sulfate attack resistance and sulfide bacterial of concrete. Add 0%, 1%, 3%, 6% and 9% oyster shell powder to the concrete to replace part of the sand. The study conducted flow tests, compressive strength tests, sulfate corrosion resistance and antibacterial tests. From the results, it was found that adding oyster shell powder improved the resistance to sulfate corrosion and antibacterial properties and became more effective as the substitution ratio increased. In addition, the sulfate attack resistance and antibacterial have a linear relationship of mortar with oyster shell powders.


  • Open Access

    Abrasion Behavior of Steel-Fiber-Reinforced Concrete in Hydraulic Structures

    by Yu-Wen Liu, Yu-Yuan Lin, Shih-Wei Cho

    This study investigated two types of abrasion resistance of steel–fiber-reinforced concrete in hydraulic structures, friction abrasion and impact abrasion using the ASTM C1138 underwater test and the water-borne sand test, respectively. Three water-to-cementitious-material ratios (0.50, 0.36, and 0.28), two impact angles (45° and 90°), plain concrete, and steel–fiber-reinforced concrete were employed. Test results showed that the abrasive action and principal resistance varied between the two test methods. The average impact abrasion rates (IARs) of concrete were approximately 8–17 times greater than the average friction abrasion rate (FARs). In general, the impact abrasion loss of the concrete surface impacted at a vertical angle was higher than that of impacted at a 45 degree angle. Moreover, the average FAR and IAR decreased when the concrete was reinforced with steel fibers. The steel fibers acted as shields to prevent the concrete material behind the fibers from abrasion, thus improving abrasion resistance. In both the underwater and waterborne sand flow methods, the resistance to abrasion of concrete without steel fibers increased as the water/cementitious material ratio (w/cm) decreased, and the concrete compressive strength also increased.


  • Abrasion resistance of concrete containing surface cracks

    by Yu-Wen Liu, Kun-Sheng Pann

    This study evaluates concrete resistance of concrete specimens with abrasion in three crack patterns (0°, 45° and 90°), four surface crack widths (0.5, 1, 2 and 3 mm) and two silica fume (5% and 10%) contents. The ASTM C 944 was used to evaluate the abrasion resistance. The boundary element method (BEM) was used to analyze the stress distribution on concrete surfaces with/without cracks. Test results conclude that the abrasion resistance of test specimens containing 0°, 45° and 90° cracks and 1 mm crack widths showed a decrease of about 98%, 108% and 125%, respectively, as compared to specimen without cracks. The abrasion resistance loss of concrete with 90° cracks is lower than concrete with 0° cracks that have the same width and length. Moreover, concrete with silica fume additions can improve the abrasive resistance of specimens with surface cracks. The maximum concrete stresses based on BEM analysis, of specimens containing 0°, 45° and 90° cracks are 11, 26 and 34 times the stress on specimens without surface cracks.


  • Relation between Porosity and Compressive Strength of Slag Concrete

    by An-Shun Cheng, Tsong Yen, Yu-Wen Liu, Yeong-Nain Sheen

    This research aims to investigate the pore structures characteristics of slag concrete and its correlation with the compressive strength. In the study, three water/binder ratios (0.35, 0.50, 0.70) and three substitute ratios of cement with slag (10%, 20%, 40%) were selected for preparing concrete specimens. The specimens were tested at five ages (1–56 days) for compressive strength and MIP porosity measurement. Test results show that the larger the water/binder is, the more the total pore volume and capillary pore volume of slag concrete will be. At early ages, the pore volume of slag concrete is greater than that of plain concrete, while at later ages, the pore volume of slag concrete will decrease gradually, and the larger the slag substitute ratio is, the less the pore volume will be. Moreover, the compressive strength of slag concrete has a close correlation with both the total pore volume and capillary pore volume (0.01μm∼10μm), in which a closer correlation stands for the bigger capillary pore volume (0.1μm∼10μm). Therefore, using the bigger capillary pore volume to predict the compressive strength of slag concrete can reach to an optimum result.


  • Erosive resistibility of low cement high performance concrete

    by Yu-Wen Liu, Tsong Yen, Tsao-Hua Hsu, Jenq-Chuan Liou