Xiaobo Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xiaobo Zhang has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Jisen Qiao
School of Materials Science and Engineering, Lanzhou University of Technology, Lanzhou 730050, China
2 shared publications - Qilun Li
School of Materials Science and Engineering, Lanzhou University of Technology, Lanzhou 730050, China
2 shared publications Bin Yue
College of Geography and Environmental Engineering, Lanzhou City University, Lanzhou 730070, P. R. China
1 shared publication- Ce Guo
School of Materials Science and Engineering, Lanzhou University of Technology, Lanzhou 730050, China
1 shared publication - Lei Wang
School of Materials Science and Engineering, Lanzhou University of Technology, Lanzhou 730050, China
1 shared publication Lingling Li
State Key Laboratory of Advanced Processing and Recycling of Non-ferrous Metals, School of Materials Science and Engineering, Lanzhou University of Technology, Lanzhou 730050, P. R. China
1 shared publication
Latest Publications
- Open Access
Effect of Multistage Solution Aging Heat Treatment on Mechanical Properties and Precipitated Phase Characteristics of High-Strength Toughened 7055 Alloy
In this paper, a one-step hot extrusion dual-stage solution treatment method is employed to fabricate high-strength and tough T-shaped complex cross-section 7055 (Al-Zn-Mg-Cu-Zr) alloy profiles, and a detailed investigation is conducted on the microstructure and mechanical properties. The results indicate that the comprehensive mechanical properties of the 7055 aluminum extruded alloy using the two-stage solution aging treatment are excellent. This is particularly evident in the balance between strength and ductility, where outstanding strength is accompanied by a plasticity that is maintained at 13.2%. During the extrusion process, the deformation textures are mainly composed of brass and copper, forming a 15.1% recrystallization texture Cube. In addition, the equilibrium phase η(MgZn2) precipitated in the grain is the main strengthening phase, and there are large discontinuous grain boundary precipitates at the grain boundary, which hinders the grain boundary dislocation movement and has great influence on the mechanical properties of alloy materials.
Open AccessEffect of Multistage Solution Aging Heat Treatment on Mechanical Properties and Precipitated Phase Characteristics of High-Strength Toughened 7055 Alloy
In this paper, a one-step hot extrusion dual-stage solution treatment method is employed to fabricate high-strength and tough T-shaped complex cross-section 7055 (Al-Zn-Mg-Cu-Zr) alloy profiles, and a detailed investigation is conducted on the microstructure and mechanical properties. The results indicate that the comprehensive mechanical properties of the 7055 aluminum extruded alloy using the two-stage solution aging treatment are excellent. This is particularly evident in the balance between strength and ductility, where outstanding strength is accompanied by a plasticity that is maintained at 13.2%. During the extrusion process, the deformation textures are mainly composed of brass and copper, forming a 15.1% recrystallization texture Cube. In addition, the equilibrium phase η(MgZn2) precipitated in the grain is the main strengthening phase, and there are large discontinuous grain boundary precipitates at the grain boundary, which hinders the grain boundary dislocation movement and has great influence on the mechanical properties of alloy materials.
- Open Access
The Effect of Extrusion and Heat Treatment on the Microstructure and Tensile Properties of 2024 Aluminum Alloy
Hot extrusion forming is one of the best cost-effective processing methods to obtain high-strength aluminum alloys. In order to obtain high performance 2024 aluminum alloy for the aero and automobile industries, this research comprehensively uses heat treatment and reverse isothermal extrusion technology to prepare 2024 alloy. The effects of homogenization, extrusion and post-extrusion annealing treatment on the microstructure and mechanical properties of 2024 aluminum alloy were discussed in detail. The results indicate that the grain refinement of the extruded alloy material is significant. The coarse eutectic microstructure at the grain boundaries was refined, and these grains tended to be uniformly distributed after the annealing treatment. Extruded 2024 aluminum alloy material mainly has S (Al2CuMg) and Al7Cu2Fe second phases. The appearance of a large number of S phases led to a significant improvement in the properties of the alloy with an increase in tensile strength and elongation of 176% and 547%, respectively. In addition, EBSD analysis showed a significant meritocratic growth in the extrusion direction with the appearance of Copper {112} rolling weaving, which led to process hardening and the strength improvement of the alloy.
Open AccessThe Effect of Extrusion and Heat Treatment on the Microstructure and Tensile Properties of 2024 Aluminum Alloy
Hot extrusion forming is one of the best cost-effective processing methods to obtain high-strength aluminum alloys. In order to obtain high performance 2024 aluminum alloy for the aero and automobile industries, this research comprehensively uses heat treatment and reverse isothermal extrusion technology to prepare 2024 alloy. The effects of homogenization, extrusion and post-extrusion annealing treatment on the microstructure and mechanical properties of 2024 aluminum alloy were discussed in detail. The results indicate that the grain refinement of the extruded alloy material is significant. The coarse eutectic microstructure at the grain boundaries was refined, and these grains tended to be uniformly distributed after the annealing treatment. Extruded 2024 aluminum alloy material mainly has S (Al2CuMg) and Al7Cu2Fe second phases. The appearance of a large number of S phases led to a significant improvement in the properties of the alloy with an increase in tensile strength and elongation of 176% and 547%, respectively. In addition, EBSD analysis showed a significant meritocratic growth in the extrusion direction with the appearance of Copper {112} rolling weaving, which led to process hardening and the strength improvement of the alloy.
- 22 June 2022
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 46 (30) , 14346-14352
Facile synthesis and lithium storage performance of tiny oxygen vacancy-enriched zinc manganate nanoparticles anchored on a reduced graphene oxide nanocomposite
Tiny ZnMn2O4 anchored on an rGO nanosheet composite with rich oxygen vacancies was synthesized and applied as a lithium ion battery anode.
- 22 June 2022
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 46 (30) , 14346-14352
Facile synthesis and lithium storage performance of tiny oxygen vacancy-enriched zinc manganate nanoparticles anchored on a reduced graphene oxide nanocomposite
Tiny ZnMn2O4 anchored on an rGO nanosheet composite with rich oxygen vacancies was synthesized and applied as a lithium ion battery anode.
- Open Access
Microstructure and Fracture Behavior of Special Multilayered Steel
In this research, multilayered steel (MLS), which is composed of middle-carbon martensite steel, high-carbon martensite steel, and a pure Ni thin layer was obtained by the accumulative roll-bonding method. The microstructure and mechanical properties of the MLS were investigated by scanning electron microscopy (SEM), Vickers microhardness, tensile, and bending tests. In-situ SEM tensile tests were used to observe the crack initiation and propagation processes during the tensile loading. The results show that the ultimate tensile strength and bending strength of the MLS can reach 946 MPa and 3153 MPa, and the maximum elongation can reach 18%, which is related to the better combined quality of the interface. The middle and larger martensite layer (ML) becomes the weakest link of tensile fracture and interfacial delamination of the MLS during the tensile processes, because there are lots of large hard blocks Cr23C6 phases distributed in the middle thicker ML layer. Besides, the MLS can withstand larger bending deformation. When the MLS was bent to 180 degrees, neither macro-cracks in the outer side of the bending parts nor interfacial delamination can be found.
Open AccessMicrostructure and Fracture Behavior of Special Multilayered Steel
In this research, multilayered steel (MLS), which is composed of middle-carbon martensite steel, high-carbon martensite steel, and a pure Ni thin layer was obtained by the accumulative roll-bonding method. The microstructure and mechanical properties of the MLS were investigated by scanning electron microscopy (SEM), Vickers microhardness, tensile, and bending tests. In-situ SEM tensile tests were used to observe the crack initiation and propagation processes during the tensile loading. The results show that the ultimate tensile strength and bending strength of the MLS can reach 946 MPa and 3153 MPa, and the maximum elongation can reach 18%, which is related to the better combined quality of the interface. The middle and larger martensite layer (ML) becomes the weakest link of tensile fracture and interfacial delamination of the MLS during the tensile processes, because there are lots of large hard blocks Cr23C6 phases distributed in the middle thicker ML layer. Besides, the MLS can withstand larger bending deformation. When the MLS was bent to 180 degrees, neither macro-cracks in the outer side of the bending parts nor interfacial delamination can be found.