Nazimuddin M. Wasiuddin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nazimuddin M. Wasiuddin has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Andrew J. Peters
Department of Chemical Engineering, Louisiana Tech University, Ruston, LA 71270, USA
3 shared publications - Louay N. Mohammad
Louisiana State Univ
3 shared publications - Shahjalal Selim
Department of Civil Engineering, Louisiana Tech University, Ruston, LA 71270, USA
3 shared publications Delmar Salomon
Pavement Preservation Systems, LLC
2 shared publications- Jr. William King
Louisiana State Univ
2 shared publications - Kenneth Hobson
The University of Oklahoma
2 shared publications
Latest Publications
- Open Access
Binder-Level Rheological Evaluation of Virgin HDPE, LDPE, and PP as Asphalt Binder Modifiers: Baseline Assessment for Plastic Waste Recycling Applications
Increasing plastic waste and limited recycling rates underscore the need for value-added recycling applications. Polymers commonly present in plastic waste streams, including packaging films, bottles, caps, and rigid containers, may provide a practical pathway for developing plastic-modified asphalt binder (PMAB) systems. In this study, virgin high-density polyethylene (HDPE), low-density polyethylene (LDPE), and polypropylene (PP) were selected as reference modifiers to evaluate their intrinsic effects on performance grade (PG) 58-28 and PG 67-22 base binders. Conventional high-, intermediate-, and low-temperature gradings were complemented by , the Christensen–Anderson R-value (R-value), the Glover–Rowe (G-R) parameter, Linear Amplitude Sweep (LAS) fatigue analysis modeled via Viscoelastic Continuum Damage (VECD), rheological master curves, and extended Bending Beam Rheometer (BBR) testing. Modification improved high-temperature grading and LAS-based fatigue response while increasing master-curve stiffness. However, , G-R parameter, and extended BBR results indicated increased low-temperature cracking susceptibility. High-temperature grades increased by 3.4 °C, 2.8 °C, and 2.3 °C per percent HDPE, LDPE, and PP, respectively, whereas low-temperature grade losses reached 7.8 °C; HDPE produced the highest high-temperature grade improvement, while LDPE showed the greatest extended BBR grade loss, and PP exhibited the fastest physical hardening rate. These results provide a controlled binder-level baseline for evaluating HDPE, LDPE, and PP as modifiers for future PMAB development.Open AccessBinder-Level Rheological Evaluation of Virgin HDPE, LDPE, and PP as Asphalt Binder Modifiers: Baseline Assessment for Plastic Waste Recycling Applications
Increasing plastic waste and limited recycling rates underscore the need for value-added recycling applications. Polymers commonly present in plastic waste streams, including packaging films, bottles, caps, and rigid containers, may provide a practical pathway for developing plastic-modified asphalt binder (PMAB) systems. In this study, virgin high-density polyethylene (HDPE), low-density polyethylene (LDPE), and polypropylene (PP) were selected as reference modifiers to evaluate their intrinsic effects on performance grade (PG) 58-28 and PG 67-22 base binders. Conventional high-, intermediate-, and low-temperature gradings were complemented by , the Christensen–Anderson R-value (R-value), the Glover–Rowe (G-R) parameter, Linear Amplitude Sweep (LAS) fatigue analysis modeled via Viscoelastic Continuum Damage (VECD), rheological master curves, and extended Bending Beam Rheometer (BBR) testing. Modification improved high-temperature grading and LAS-based fatigue response while increasing master-curve stiffness. However, , G-R parameter, and extended BBR results indicated increased low-temperature cracking susceptibility. High-temperature grades increased by 3.4 °C, 2.8 °C, and 2.3 °C per percent HDPE, LDPE, and PP, respectively, whereas low-temperature grade losses reached 7.8 °C; HDPE produced the highest high-temperature grade improvement, while LDPE showed the greatest extended BBR grade loss, and PP exhibited the fastest physical hardening rate. These results provide a controlled binder-level baseline for evaluating HDPE, LDPE, and PP as modifiers for future PMAB development. - 9 July 2026
- Published by Springer Nature
- p. 351-357
Rheological Properties of RAP Binder Blends Modified with Different Bio-Based Recycling Agents
- 9 July 2026
- Published by Springer Nature
- p. 351-357
Rheological Properties of RAP Binder Blends Modified with Different Bio-Based Recycling Agents
- Open Access
Incorporation of Lignin Binder from Agricultural Waste to Enhance Sustainability and Performance of Asphalt Pavements
Utilizing lignin from agricultural wastes as a partial replacement for asphalt binder used in pavement presents a sustainable option, as it is abundant in nature. The effects of the addition of lignin on the properties and performance of asphalt binder and asphalt mixes were studied. Lignin was produced from rice husks, using a hydrothermal carbonization (HTC) treatment process. The rice husk-derived lignin was then mixed with a PG 67-22 binder at 0%, 5% and 10% of the mass of the total binder. The HTC treatment of rice husks at 250 °C created a powdery substance with an increased acid-insoluble lignin content and a reduced cellulose and hemicellulose content. The addition of 10% lignin was found to produce an unstable modified binder due to phase separation between the lignin and binder, thus requiring continuous stirring before use. Asphalt mixes prepared with 5% lignin exhibited better moisture-induced damage resistance compared to the control mix. Also, an improved rutting resistance of asphalt mixes was observed with the use of a lignin-modified binder. Lignin from rice husks may constitute a sustainable partial substitute for a crude-oil-based binder.
Open AccessIncorporation of Lignin Binder from Agricultural Waste to Enhance Sustainability and Performance of Asphalt Pavements
Utilizing lignin from agricultural wastes as a partial replacement for asphalt binder used in pavement presents a sustainable option, as it is abundant in nature. The effects of the addition of lignin on the properties and performance of asphalt binder and asphalt mixes were studied. Lignin was produced from rice husks, using a hydrothermal carbonization (HTC) treatment process. The rice husk-derived lignin was then mixed with a PG 67-22 binder at 0%, 5% and 10% of the mass of the total binder. The HTC treatment of rice husks at 250 °C created a powdery substance with an increased acid-insoluble lignin content and a reduced cellulose and hemicellulose content. The addition of 10% lignin was found to produce an unstable modified binder due to phase separation between the lignin and binder, thus requiring continuous stirring before use. Asphalt mixes prepared with 5% lignin exhibited better moisture-induced damage resistance compared to the control mix. Also, an improved rutting resistance of asphalt mixes was observed with the use of a lignin-modified binder. Lignin from rice husks may constitute a sustainable partial substitute for a crude-oil-based binder.
- Open Access
- 21 June 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (13) , 9897
Developing Sustainable Asphalt Mixtures Using High-Density Polyethylene Plastic Waste Material
There is growing interest in sustainable road pavement technologies to protect the environment and provide economic benefits. Post-consumer recycled (PCR) plastics are considered for construction to address the threat of plastic waste materials (PWM) and to improve sustainability. Asphalt pavement construction is highly considered for PWM recycling due to its large daily production. The purpose of this study is to investigate the performance of asphalt mixture containing PWM, specifically high-density polyethylene (HDPE), and compare its performance with two conventional mixtures. Three asphalt mixtures were considered: (1) mixture with asphalt binder PG 76-22 (SBS-modified); (2) mixture with asphalt binder PG 70-22 (SBS-modified); and (3) mixture with binder PG 67-22 and 3% HDPE (the plastic mixture). The rheological properties of the modified asphalt binders and the performance of the modified asphalt mixtures were evaluated. The long-term field performance of the pavements was modeled using AASHTOWare software (v.1.1.6) for the three mixtures considered. The results showed that all the mixtures were able to comply with the cracking threshold specified by the Louisiana Department of Transportation and Development (LaDOTD) for high-traffic volume roads. In addition, the plastic asphalt mixture showed similar performance to the one containing PG 70-22 (SBS-modified) asphalt binder.
- 21 June 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (13) , 9897
Open AccessDeveloping Sustainable Asphalt Mixtures Using High-Density Polyethylene Plastic Waste Material
There is growing interest in sustainable road pavement technologies to protect the environment and provide economic benefits. Post-consumer recycled (PCR) plastics are considered for construction to address the threat of plastic waste materials (PWM) and to improve sustainability. Asphalt pavement construction is highly considered for PWM recycling due to its large daily production. The purpose of this study is to investigate the performance of asphalt mixture containing PWM, specifically high-density polyethylene (HDPE), and compare its performance with two conventional mixtures. Three asphalt mixtures were considered: (1) mixture with asphalt binder PG 76-22 (SBS-modified); (2) mixture with asphalt binder PG 70-22 (SBS-modified); and (3) mixture with binder PG 67-22 and 3% HDPE (the plastic mixture). The rheological properties of the modified asphalt binders and the performance of the modified asphalt mixtures were evaluated. The long-term field performance of the pavements was modeled using AASHTOWare software (v.1.1.6) for the three mixtures considered. The results showed that all the mixtures were able to comply with the cracking threshold specified by the Louisiana Department of Transportation and Development (LaDOTD) for high-traffic volume roads. In addition, the plastic asphalt mixture showed similar performance to the one containing PG 70-22 (SBS-modified) asphalt binder.
- 26 September 2021
- Published by Springer Nature
- p. 719-724
Establishing Correlations Between Force Ductility and DSR Parameters of Asphalt Emulsion Residues
- 26 September 2021
- Published by Springer Nature
- p. 719-724
Establishing Correlations Between Force Ductility and DSR Parameters of Asphalt Emulsion Residues
- 26 September 2021
- Published by Springer Nature
- p. 65-71
A Comparative Study of RTFO, PAV and UV Aging Using FT-IRS and DSR Tests
- 26 September 2021
- Published by Springer Nature
- p. 65-71
A Comparative Study of RTFO, PAV and UV Aging Using FT-IRS and DSR Tests
- 26 September 2021
- Published by Springer Nature
- p. 1111-1117
In-Situ Measurements of Variations of RAP Contents in Hot Mix Asphalt by a Handheld FT-IR Spectrometer
- 26 September 2021
- Published by Springer Nature
- p. 1111-1117
In-Situ Measurements of Variations of RAP Contents in Hot Mix Asphalt by a Handheld FT-IR Spectrometer
- 6 November 2019
- Published by Springer Nature in International Journal of Pavement Research and Technology
- Vol. 12 (6) , 604-612
A Novel Method for Polymer Content Determination in Asphalt Binder and Emulsion
- 6 November 2019
- Published by Springer Nature in International Journal of Pavement Research and Technology
- Vol. 12 (6) , 604-612
A Novel Method for Polymer Content Determination in Asphalt Binder and Emulsion