Kenneth Hobson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kenneth Hobson has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Musharraf Zaman
The University of Oklahoma
4 shared publications - Syed Ashik Ali
Univ. of Oklahoma
4 shared publications - Nazimuddin M. Wasiuddin
Richard A. Rula School of Civil & Environmental Engineering, Mississippi State University, Starkville, MS 39762, USA
2 shared publications - Dar Hao Chen
Changsha University of Science and Technology. Chiling Road 45#, Changsha, Hunan, P.R.China, 410076 and Texas Department of Transportation, 4203 Bull Creek #39, Austin, TX 78731
1 shared publication - Joan G. Lynam
Chemical Engineering Department, Louisiana Tech University, 600 Dan Reneau Drive, Ruston, LA 71272, USA
1 shared publication - Matias M. Mendez Larrain
School of Civil Engineering and Environmental Science, The University of Oklahoma, Norman, OK 73019, USA
1 shared publication
Latest Publications
- 9 July 2026
- Published by Springer Nature
- p. 351-357
Rheological Properties of RAP Binder Blends Modified with Different Bio-Based Recycling Agents
- 9 July 2026
- Published by Springer Nature
- p. 351-357
Rheological Properties of RAP Binder Blends Modified with Different Bio-Based Recycling Agents
- Open Access
Incorporation of Lignin Binder from Agricultural Waste to Enhance Sustainability and Performance of Asphalt Pavements
Utilizing lignin from agricultural wastes as a partial replacement for asphalt binder used in pavement presents a sustainable option, as it is abundant in nature. The effects of the addition of lignin on the properties and performance of asphalt binder and asphalt mixes were studied. Lignin was produced from rice husks, using a hydrothermal carbonization (HTC) treatment process. The rice husk-derived lignin was then mixed with a PG 67-22 binder at 0%, 5% and 10% of the mass of the total binder. The HTC treatment of rice husks at 250 °C created a powdery substance with an increased acid-insoluble lignin content and a reduced cellulose and hemicellulose content. The addition of 10% lignin was found to produce an unstable modified binder due to phase separation between the lignin and binder, thus requiring continuous stirring before use. Asphalt mixes prepared with 5% lignin exhibited better moisture-induced damage resistance compared to the control mix. Also, an improved rutting resistance of asphalt mixes was observed with the use of a lignin-modified binder. Lignin from rice husks may constitute a sustainable partial substitute for a crude-oil-based binder.
Open AccessIncorporation of Lignin Binder from Agricultural Waste to Enhance Sustainability and Performance of Asphalt Pavements
Utilizing lignin from agricultural wastes as a partial replacement for asphalt binder used in pavement presents a sustainable option, as it is abundant in nature. The effects of the addition of lignin on the properties and performance of asphalt binder and asphalt mixes were studied. Lignin was produced from rice husks, using a hydrothermal carbonization (HTC) treatment process. The rice husk-derived lignin was then mixed with a PG 67-22 binder at 0%, 5% and 10% of the mass of the total binder. The HTC treatment of rice husks at 250 °C created a powdery substance with an increased acid-insoluble lignin content and a reduced cellulose and hemicellulose content. The addition of 10% lignin was found to produce an unstable modified binder due to phase separation between the lignin and binder, thus requiring continuous stirring before use. Asphalt mixes prepared with 5% lignin exhibited better moisture-induced damage resistance compared to the control mix. Also, an improved rutting resistance of asphalt mixes was observed with the use of a lignin-modified binder. Lignin from rice husks may constitute a sustainable partial substitute for a crude-oil-based binder.
- Open Access
- 13 October 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (20) , 14848
Calibration of Effective Structural Number and Tensile Strain Models Using Traffic Speed Deflectometer (TSD) Data for Enhanced Project-Level Assessment on Flexible and Composite Pavements
Pavement deterioration models provide the basis for predicting future changes in network conditions, estimating future funding needs, and determining the effectiveness and timing of maintenance and rehabilitation activities. Determining the accurate structural condition of pavements helps identify effective maintenance strategies which enhance the sustainability and service life of pavements. This study aimed to use the Traffic Speed Deflectometer (TSD) and Fast Falling Weight Deflectometer (FFWD) for project-level evaluation of pavements and use pavement properties to calibrate current models that help to predict the structural condition of pavements. Model parameters were calibrated to determine the effective structural number and tensile strains at the bottom of asphalt concrete for asphalt and composite pavements from TSD deflections. Tensile strains from the KENLAYER highlighted varied behaviors for composite pavements. A significant improvement in the calibration was observed for asphalt concrete pavements. While the TSD has higher daily operational costs than FWD, its per-mile cost is significantly lower, making it a viable choice for extensive coverage, even though the quantitative results might differ between the two devices.
- 13 October 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (20) , 14848
Open AccessCalibration of Effective Structural Number and Tensile Strain Models Using Traffic Speed Deflectometer (TSD) Data for Enhanced Project-Level Assessment on Flexible and Composite Pavements
Pavement deterioration models provide the basis for predicting future changes in network conditions, estimating future funding needs, and determining the effectiveness and timing of maintenance and rehabilitation activities. Determining the accurate structural condition of pavements helps identify effective maintenance strategies which enhance the sustainability and service life of pavements. This study aimed to use the Traffic Speed Deflectometer (TSD) and Fast Falling Weight Deflectometer (FFWD) for project-level evaluation of pavements and use pavement properties to calibrate current models that help to predict the structural condition of pavements. Model parameters were calibrated to determine the effective structural number and tensile strains at the bottom of asphalt concrete for asphalt and composite pavements from TSD deflections. Tensile strains from the KENLAYER highlighted varied behaviors for composite pavements. A significant improvement in the calibration was observed for asphalt concrete pavements. While the TSD has higher daily operational costs than FWD, its per-mile cost is significantly lower, making it a viable choice for extensive coverage, even though the quantitative results might differ between the two devices.
- 6 July 2021
- Published by Springer Nature in International Journal of Pavement Research and Technology
- Vol. 15 (3) , 561-576
Evaluation of Transverse Cracking in Flexible Pavements Using Field Investigation and AASHTOWare Pavement ME Design
- 6 July 2021
- Published by Springer Nature in International Journal of Pavement Research and Technology
- Vol. 15 (3) , 561-576
Evaluation of Transverse Cracking in Flexible Pavements Using Field Investigation and AASHTOWare Pavement ME Design