Swagat Dwibedi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Swagat Dwibedi has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Suyog Jhavar
Department of Mechanical Engineering, VIT-AP University, Amravathi, India
6 shared publications - Suraj Prasad
Veer Surendra Sai University of Technology
3 shared publications Swarup Bag
Indian Institute of Technology Guwahati
3 shared publications- Uttam Kumar Tarai
DRIEMS University
3 shared publications Bikash Kumar
Indian Institute of Technology Guwahati
2 shared publications- Swarup Bag
Indian Institute of Technology Guwahati
2 shared publications
Latest Publications
- Open Access
- 25 June 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- p. 973-981
Influence of Process Parameters on the Microstructural and Mechanical Characteristics of TLP Bonded IN718
Study explores the role of process parameters in joining IN718 with the TLP bonding process is explored. Microstructure evolution and mechanical performance of the bond are investigated using scanning electron microscopy, tensile test, and micro-hardness test. The bond metallurgy showed three distinct zones: the base material zone, the diffusion-affected zone containing a large number of boride precipitates, and the isothermal solidification zone. Further investigation reveals that the ISZ contains a few brittle intermetallic particles, which reduce the mechanical properties of the bond. The results demonstrates that higher bonding temperature, time, optimal interlayer thickness, and pressure enhance the mechanical and microstructural properties of the bond. The bond formed at 1423 K bonding temperature, 1.5 h holding time, 80 μm interlayer thickness, and 12.5 kg load demonstrates the highest strength of 625 MPa.
- 25 June 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- p. 973-981
Open AccessInfluence of Process Parameters on the Microstructural and Mechanical Characteristics of TLP Bonded IN718
Study explores the role of process parameters in joining IN718 with the TLP bonding process is explored. Microstructure evolution and mechanical performance of the bond are investigated using scanning electron microscopy, tensile test, and micro-hardness test. The bond metallurgy showed three distinct zones: the base material zone, the diffusion-affected zone containing a large number of boride precipitates, and the isothermal solidification zone. Further investigation reveals that the ISZ contains a few brittle intermetallic particles, which reduce the mechanical properties of the bond. The results demonstrates that higher bonding temperature, time, optimal interlayer thickness, and pressure enhance the mechanical and microstructural properties of the bond. The bond formed at 1423 K bonding temperature, 1.5 h holding time, 80 μm interlayer thickness, and 12.5 kg load demonstrates the highest strength of 625 MPa.
- 28 January 2025
- Published by Springer Nature
- p. 233-244
Influence of Post Bond Heat Treatment on IN718 Joints: An Experimental Study
- 28 January 2025
- Published by Springer Nature
- p. 233-244
Influence of Post Bond Heat Treatment on IN718 Joints: An Experimental Study
- 28 January 2025
- Published by Springer Nature
- p. 201-211
Physical Phenomena Behind the Enhancement of Joint Properties in Solution-Treated Nickel-Based Superalloy
- 28 January 2025
- Published by Springer Nature
- p. 201-211
Physical Phenomena Behind the Enhancement of Joint Properties in Solution-Treated Nickel-Based Superalloy
- 28 January 2025
- Published by Springer Nature
- p. 213-223
Influence of Weld Time on Joint Behavior of IN625-SS316L Weldments
- 28 January 2025
- Published by Springer Nature
- p. 213-223
Influence of Weld Time on Joint Behavior of IN625-SS316L Weldments
- 28 January 2025
- Published by Springer Nature
- p. 225-231
Study on Dissimilar SS316L-Incoloy 800 Joints with Inconel 82 as Filler Metal
- 28 January 2025
- Published by Springer Nature
- p. 225-231
Study on Dissimilar SS316L-Incoloy 800 Joints with Inconel 82 as Filler Metal
- 28 January 2025
- Published by Springer Nature
- p. 103-112
Calculation of Ni–Cu, Ni–Ag, and Cu–Ag Phase Diagram Using CALPHAD Method
- 28 January 2025
- Published by Springer Nature
- p. 103-112
Calculation of Ni–Cu, Ni–Ag, and Cu–Ag Phase Diagram Using CALPHAD Method
- 1 October 2024
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series D
- Vol. 106 (3) , 1967-1975
Impact of Weld Time and Solution Treatment on the Performance of IN625 Spot Joints: An Experimental Study
- 1 October 2024
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series D
- Vol. 106 (3) , 1967-1975
Impact of Weld Time and Solution Treatment on the Performance of IN625 Spot Joints: An Experimental Study
- 11 September 2024
- Published by Taylor & Francis in Welding International
- Vol. 38 (9) , 583-617
Critical assessment on the influence of process parameters in micro-plasma arc welding process: a review
- 11 September 2024
- Published by Taylor & Francis in Welding International
- Vol. 38 (9) , 583-617
Critical assessment on the influence of process parameters in micro-plasma arc welding process: a review
- 17 October 2023
- Published by Springer Nature
- p. 307-315
An Experimental Study to Probe Defect Formation and Failure Mode in Dissimilar Spot Joints
- 17 October 2023
- Published by Springer Nature
- p. 307-315
An Experimental Study to Probe Defect Formation and Failure Mode in Dissimilar Spot Joints
- 12 October 2021
- Published by Springer Nature
- p. 305-313
Influence of Squeeze Time on Fracture Mode of SS304 Spot Weldments
- 12 October 2021
- Published by Springer Nature
- p. 305-313
Influence of Squeeze Time on Fracture Mode of SS304 Spot Weldments