Chaouki Sadik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Chaouki Sadik has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Iz-Eddine El Amrani El Hassani
University Mohammed V of Rabat
3 shared publications A. Al Albizane
University Hassan II, Morocco
1 shared publicationA. Albizane
Université Hassan II, Faculté des Sciences et Technique – Mohammedia, Département de Chimie, Maroc
1 shared publicationAbdelilah El Haddar
Laboratory of Applied Geosciences, Faculty of Sciences, University of Mohammed 1, Oujda, Morocco
1 shared publicationAboubakar Moustapha
Laboratory of Physical-Chemistry, Materials and Catalysis (LCPMC), Geomaterials and Materials for Energy Team, Faculty of Sciences Ben M’Sik, Hassan II University of Casablanca, Casablanca, Morocco
1 shared publicationAchraf Harrati
Laboratory of Physical-Chemistry, Materials and Catalysis (LCPMC), Geomaterials and Materials for Energy Team, Faculty of Sciences Ben M’Sik, Hassan II University of Casablanca, Casablanca, Morocco
1 shared publication
Latest Publications
- 19 February 2025
- Published by Springer Nature in Interactions
- Vol. 246 (1) , 1-28
Assessment of bentonite effectiveness in retaining pollutants from olive oil production discharges
- 19 February 2025
- Published by Springer Nature in Interactions
- Vol. 246 (1) , 1-28
Assessment of bentonite effectiveness in retaining pollutants from olive oil production discharges
- 7 January 2025
- Published by Springer Nature in Euro-Mediterranean Journal for Environmental Integration
- Vol. 10 (3) , 1407-1423
Potential use of mint waste and bentonite clay in sustainable porous ceramic manufacturing
- 7 January 2025
- Published by Springer Nature in Euro-Mediterranean Journal for Environmental Integration
- Vol. 10 (3) , 1407-1423
Potential use of mint waste and bentonite clay in sustainable porous ceramic manufacturing
- 1 September 2018
- Published by Springer Nature in Journal of the Australian Ceramic Society
- Vol. 55 (2) , 415-423
Preparation and characterization of possible basic ceramics from Moroccan magnesite
- 1 September 2018
- Published by Springer Nature in Journal of the Australian Ceramic Society
- Vol. 55 (2) , 415-423
Preparation and characterization of possible basic ceramics from Moroccan magnesite
- Open Access
- 1 December 2013
- Published by FapUNIFESP (SciELO) in Cerâmica
- Vol. 59 (352) , 609-613
Characterization of elaborated Moroccan mullite to improving porous refractories quality
Production of porous and light-weight bricks with acceptable flexural strength is accomplished. Sawdust was used as an additive to an earthenware brick to produce the pores. SEM-EDS, XRD and XRF analysis of the raw materials and the elaborated refractory were performed. Mixtures containing sawdust were prepared at different proportions (up to 30%). Apparent porosity at 1600 °C was investigated with the bulk density, water absorption, firing shrinkage and flexural strength. Microstructural investigation was carried out by both natural light microscopy and polarized light microscopy. The results obtained showed that the samples tested here maintained their shape without undergoing any deformation up to 1600 °C. The use of sawdust decreased the fired density of the bricks down to 1.24 g/cm³.
- 1 December 2013
- Published by FapUNIFESP (SciELO) in Cerâmica
- Vol. 59 (352) , 609-613
Open AccessCharacterization of elaborated Moroccan mullite to improving porous refractories quality
Production of porous and light-weight bricks with acceptable flexural strength is accomplished. Sawdust was used as an additive to an earthenware brick to produce the pores. SEM-EDS, XRD and XRF analysis of the raw materials and the elaborated refractory were performed. Mixtures containing sawdust were prepared at different proportions (up to 30%). Apparent porosity at 1600 °C was investigated with the bulk density, water absorption, firing shrinkage and flexural strength. Microstructural investigation was carried out by both natural light microscopy and polarized light microscopy. The results obtained showed that the samples tested here maintained their shape without undergoing any deformation up to 1600 °C. The use of sawdust decreased the fired density of the bricks down to 1.24 g/cm³.
- Open Access
- 3 September 2012
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 2, 01016
Influence de la nature chimique et minéralogique des argiles et du processus de fabrication sur la qualité des carreaux céramiques
This study is conducted in a multidisciplinary collaboration between geologists, chemists and industrial ceramics. The results confirm the close ralatioship existing between the composition of clays and quality of the finished ceramic pieces. The obtained specimens, under the same conditions, from two moroccan clays that are different on the chimico-mineralogical point of view, present distinct technological characteristics. The use of well selected mineral adjuvants, contributes to the balancing of raw clays and leads to a marked improvement in the quality of the ceramic product, including a reduction on their firing shrinkage and an increase of flexural strength. Concerning the effect of the manufacturing process, the application of the glaze, turns out to be the cause of bulging tiles during firing, probably because of the difference in thermal expansion coefficients of two materials clay and glaze.
- 3 September 2012
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 2, 01016
Open AccessInfluence de la nature chimique et minéralogique des argiles et du processus de fabrication sur la qualité des carreaux céramiques
This study is conducted in a multidisciplinary collaboration between geologists, chemists and industrial ceramics. The results confirm the close ralatioship existing between the composition of clays and quality of the finished ceramic pieces. The obtained specimens, under the same conditions, from two moroccan clays that are different on the chimico-mineralogical point of view, present distinct technological characteristics. The use of well selected mineral adjuvants, contributes to the balancing of raw clays and leads to a marked improvement in the quality of the ceramic product, including a reduction on their firing shrinkage and an increase of flexural strength. Concerning the effect of the manufacturing process, the application of the glaze, turns out to be the cause of bulging tiles during firing, probably because of the difference in thermal expansion coefficients of two materials clay and glaze.