Bo Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Bo Liu has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
Salah Ibrahim
2 shared publications- Shuisheng He
Department of Mechanical Engineering, University of Sheffield, Sheffield S1 3JD, UK
2 shared publications - Weeratunge Malalasekera
School of Mechanical and Manufacturing Engineering, Loughborough University, Loughborough, UK
2 shared publications - Zhiyuan Cao
School of Power and Energy, Northwestern Polytechnical University, Xi’an, China
2 shared publications Asela Uyanwaththa
Wolfson School of Mechanical, Elect and Manuf. Eng, Loughborough University Leicestershire, UK
1 shared publication- Athanasios Kolios
DTU Wind and Energy Systems, Technical University of Denmark, 4000 Roskilde, Denmark
1 shared publication
Latest Publications
- Open Access
- 6 September 2026
- Published by Elsevier in International Journal of Heat and Fluid Flow
- Vol. 122
Benchmarking of CFD modelling of a reactor vessel auxiliary cooling system (RVACS)
- 6 September 2026
- Published by Elsevier in International Journal of Heat and Fluid Flow
- Vol. 122
Open AccessBenchmarking of CFD modelling of a reactor vessel auxiliary cooling system (RVACS)
- 13 June 2025
- Published by Taylor & Francis in Nuclear Technology
- Vol. 211 (10) , 2559-2576
Unsteady Reynolds-Averaged Navier-Stokes Simulation of Turbulent Buoyant Jets Issued into a Model HTGR Cavity with Bottom Venting
- 13 June 2025
- Published by Taylor & Francis in Nuclear Technology
- Vol. 211 (10) , 2559-2576
Unsteady Reynolds-Averaged Navier-Stokes Simulation of Turbulent Buoyant Jets Issued into a Model HTGR Cavity with Bottom Venting
- 26 May 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 235 (23) , 6833-6846
Performance enhancing for a highly loaded tandem cascade by endwall incoming vortex–corner separation interaction
In highly loaded tandem compressor cascades, corner separations can still exist. In order to eliminate corner separations in highly loaded tandem compressor cascades, incoming vortex–corner separation interaction mechanism was investigated. Different schemes of the vortex generators, which located at different pitchwise locations and could generate vortexes with different rotation directions, were designed and investigated numerically. Results show that, severe corner separation occurred at the front blade passage of the tandem cascade; by utilizing flow control method of incoming vortex–corner separation interaction, the corner separation could be reduced significantly. The optimal control effect of incoming vortex on corner separation was achieved with anticlockwise rotation and the vortex generator is located right ahead of the leading edge of tandem cascade, a maximum loss coefficient reduction of 21.8% being achieved. Different from single blade configuration, the boundary layer of tandem cascade was regenerated at rear blade suction surface due to the injection flow from blade gap between the two blades. Though corner separations could be reduced at both conditions, the loss of tandem cascade with clockwise incoming vortex is higher than that with anticlockwise vortex, and a smaller corner separation region at suction surface was achieved by utilizing clockwise vortex. The mechanism was that anticlockwise incoming vortex reduced the corner separation but increased secondary flow, while clockwise vortex enhanced passage vortex and decreased secondary flow. For clockwise incoming vortex near pressure surface, the vortex would be divided into two parts at the leading edge of rear blade, one would go through the blade gap and deteriorate flow fluid near rear blade suction surface, the other flowed downstream along pressure surface. The rotation direction of different incoming vortexes became the same as the passage vortex at rear blade passage of tandem cascade, which was mainly due to the effect of secondary flow.
- 26 May 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 235 (23) , 6833-6846
Performance enhancing for a highly loaded tandem cascade by endwall incoming vortex–corner separation interaction
In highly loaded tandem compressor cascades, corner separations can still exist. In order to eliminate corner separations in highly loaded tandem compressor cascades, incoming vortex–corner separation interaction mechanism was investigated. Different schemes of the vortex generators, which located at different pitchwise locations and could generate vortexes with different rotation directions, were designed and investigated numerically. Results show that, severe corner separation occurred at the front blade passage of the tandem cascade; by utilizing flow control method of incoming vortex–corner separation interaction, the corner separation could be reduced significantly. The optimal control effect of incoming vortex on corner separation was achieved with anticlockwise rotation and the vortex generator is located right ahead of the leading edge of tandem cascade, a maximum loss coefficient reduction of 21.8% being achieved. Different from single blade configuration, the boundary layer of tandem cascade was regenerated at rear blade suction surface due to the injection flow from blade gap between the two blades. Though corner separations could be reduced at both conditions, the loss of tandem cascade with clockwise incoming vortex is higher than that with anticlockwise vortex, and a smaller corner separation region at suction surface was achieved by utilizing clockwise vortex. The mechanism was that anticlockwise incoming vortex reduced the corner separation but increased secondary flow, while clockwise vortex enhanced passage vortex and decreased secondary flow. For clockwise incoming vortex near pressure surface, the vortex would be divided into two parts at the leading edge of rear blade, one would go through the blade gap and deteriorate flow fluid near rear blade suction surface, the other flowed downstream along pressure surface. The rotation direction of different incoming vortexes became the same as the passage vortex at rear blade passage of tandem cascade, which was mainly due to the effect of secondary flow.
- Open Access
- 20 May 2021
- Published by Tech Science Press in Frontiers in Heat and Mass Transfer
- Vol. 16
ALGORITHM AND INFLUENCE FACTOR STUDY ON FLOW PATTERN TRANSITION FROM STRATIFIED FLOW TO NON-STRATIFIED FLOW OF GAS-LIQUID TWO-PHASE FLOW
A premiere free-access and peer-reviewed frontier journal site, serving the needs of the thermal-fluids community. See the latest research or submit an article. Quickly share your research with the global thermal-fluids community, for increased citations and impact at no cost.
- 20 May 2021
- Published by Tech Science Press in Frontiers in Heat and Mass Transfer
- Vol. 16
Open AccessALGORITHM AND INFLUENCE FACTOR STUDY ON FLOW PATTERN TRANSITION FROM STRATIFIED FLOW TO NON-STRATIFIED FLOW OF GAS-LIQUID TWO-PHASE FLOW
A premiere free-access and peer-reviewed frontier journal site, serving the needs of the thermal-fluids community. See the latest research or submit an article. Quickly share your research with the global thermal-fluids community, for increased citations and impact at no cost.
- 21 September 2020
- Published by ASME International
Effect of Boundary Layer Suction on the Corner Separation in a Highly Loaded Axial Compressor Cascade
Control of corner separation in axial compressor blade rows has attracted much interest due to its potential to improve compressor efficiency and the energy utilization in turbomachinery. This paper investigates the effectiveness and mechanisms of boundary layer suction in controlling the corner separation of a highly loaded axial compressor cascade. Numerical simulations have been carried out to investigate the effect of different suction schemes on the loss downstream of the cascade and the change in incidence characteristics with the variation of the suction flow rate. The results show that the effectiveness of flow suction in controlling the flow separation depends heavily on the proportion of the blade for which it is applied. It was found that suction along part of the blade span on the suction surface could effectively remove the separation at the region of the span influenced by the suction slot. However, this resulted in a deterioration of the flow field at other parts of the span. The full span suction scheme on the suction surface not only eliminated the separation of the boundary layer in the middle of the blade, but also significantly improved the flow uniformity near the end-wall. Despite the improvement in flow uniformity using the full-span suction scheme, a three-dimensional (3D) corner separation still existed due to the strong cross-passage pressure gradient. To improve the flow field uniformity further, two combined suction schemes with one spanwise slot on the suction surface and another slot on the end-wall were designed in order to fully remove both the separated flow on the blade suction surface and the 3D corner separation. It was found that the total pressure loss coefficient was reduced significantly by 63.8% with suction flow rates of 1.88% and 0.82% for the slots on the suction surface and the end-wall respectively. Further work showed that the behavior of the loss coefficient is different as the combination of suction flow rates is changed for different incidence. The cascade loss at high incidence operation can be more effectively reduced with suction control on the end-wall. When implementing combined suction, it is necessary to determine the best combination of suction flow rate according to the incidence level.
- 21 September 2020
- Published by ASME International
Effect of Boundary Layer Suction on the Corner Separation in a Highly Loaded Axial Compressor Cascade
Control of corner separation in axial compressor blade rows has attracted much interest due to its potential to improve compressor efficiency and the energy utilization in turbomachinery. This paper investigates the effectiveness and mechanisms of boundary layer suction in controlling the corner separation of a highly loaded axial compressor cascade. Numerical simulations have been carried out to investigate the effect of different suction schemes on the loss downstream of the cascade and the change in incidence characteristics with the variation of the suction flow rate. The results show that the effectiveness of flow suction in controlling the flow separation depends heavily on the proportion of the blade for which it is applied. It was found that suction along part of the blade span on the suction surface could effectively remove the separation at the region of the span influenced by the suction slot. However, this resulted in a deterioration of the flow field at other parts of the span. The full span suction scheme on the suction surface not only eliminated the separation of the boundary layer in the middle of the blade, but also significantly improved the flow uniformity near the end-wall. Despite the improvement in flow uniformity using the full-span suction scheme, a three-dimensional (3D) corner separation still existed due to the strong cross-passage pressure gradient. To improve the flow field uniformity further, two combined suction schemes with one spanwise slot on the suction surface and another slot on the end-wall were designed in order to fully remove both the separated flow on the blade suction surface and the 3D corner separation. It was found that the total pressure loss coefficient was reduced significantly by 63.8% with suction flow rates of 1.88% and 0.82% for the slots on the suction surface and the end-wall respectively. Further work showed that the behavior of the loss coefficient is different as the combination of suction flow rates is changed for different incidence. The cascade loss at high incidence operation can be more effectively reduced with suction control on the end-wall. When implementing combined suction, it is necessary to determine the best combination of suction flow rate according to the incidence level.
- 5 June 2020
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 6 (3)
A Numerical Study of Turbulent Upward Flow of Super Critical Water in a 2 × 2 Rod Bundle With Nonuniform Heating
This work is part of a benchmarking exercise organized by an IAEA in supercritical water-cooled reactor (SCWR) thermal-hydraulics aimed at improving the understanding and prediction accuracy of the thermal-hydraulic phenomena relevant to SCWRs. An experiment carried out using a 2 × 2 SCWR bundle at University of Wisconsin-Madison was modeled using an open-source computational fluid dynamics (CFD) code—Code_Saturne. The k–ω shear stress transport (SST) model was used to account for the buoyancy-aided turbulent flow in the fuel channel. Significant heat transfer deterioration (HTD) was observed in the boundary layer, which is commonly expected to occur in buoyancy-aided flows. For comparison, simulations were also conducted using ansysfluent with similar model setups.
- 5 June 2020
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 6 (3)
A Numerical Study of Turbulent Upward Flow of Super Critical Water in a 2 × 2 Rod Bundle With Nonuniform Heating
This work is part of a benchmarking exercise organized by an IAEA in supercritical water-cooled reactor (SCWR) thermal-hydraulics aimed at improving the understanding and prediction accuracy of the thermal-hydraulic phenomena relevant to SCWRs. An experiment carried out using a 2 × 2 SCWR bundle at University of Wisconsin-Madison was modeled using an open-source computational fluid dynamics (CFD) code—Code_Saturne. The k–ω shear stress transport (SST) model was used to account for the buoyancy-aided turbulent flow in the fuel channel. Significant heat transfer deterioration (HTD) was observed in the boundary layer, which is commonly expected to occur in buoyancy-aided flows. For comparison, simulations were also conducted using ansysfluent with similar model setups.
- 1 December 2019
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 355
Sub-channel CFD for nuclear fuel bundles
- 1 December 2019
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 355
Sub-channel CFD for nuclear fuel bundles
- Open Access
- 1 July 2018
- Published by Elsevier in Process Safety and Environmental Protection
- Vol. 117, 551-564
On the mechanism of pressure rise in vented explosions: A numerical study
- 1 July 2018
- Published by Elsevier in Process Safety and Environmental Protection
- Vol. 117, 551-564
Open AccessOn the mechanism of pressure rise in vented explosions: A numerical study
- Open Access
- 1 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 124-128
A Numerical Study of Dust Explosion Properties of Hydrogen Storage Alloy Materials
Hydride materials, used in hydrogen storage technologies, in powder form can be an explosion hazard and testing these materials using standard techniques is difficult. Research reported in this paper is an attempt to develop numerical methods to obtain explosion properties of such materials. In this work a one-dimensional transport-type model is presented to simulate the dust explosion process in a closed 20-L spherical vessel. Transport equations for energy, species and particle volume fraction are solved with the finite difference method, whilst velocity distribution and pressure are updated with numerical integration of the continuity equation. The model is first validated with experimental data and then applied to simulate the explosion process of an AB 2 - type alloy powder used for hydrogen storage.
- 1 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 124-128
Open AccessA Numerical Study of Dust Explosion Properties of Hydrogen Storage Alloy Materials
Hydride materials, used in hydrogen storage technologies, in powder form can be an explosion hazard and testing these materials using standard techniques is difficult. Research reported in this paper is an attempt to develop numerical methods to obtain explosion properties of such materials. In this work a one-dimensional transport-type model is presented to simulate the dust explosion process in a closed 20-L spherical vessel. Transport equations for energy, species and particle volume fraction are solved with the finite difference method, whilst velocity distribution and pressure are updated with numerical integration of the continuity equation. The model is first validated with experimental data and then applied to simulate the explosion process of an AB 2 - type alloy powder used for hydrogen storage.
- Open Access
- 1 September 2017
- Published by Elsevier in Fuel Processing Technology
- Vol. 164, 51-68
CFD modelling of particle shrinkage in a fluidized bed for biomass fast pyrolysis with quadrature method of moment
- 1 September 2017
- Published by Elsevier in Fuel Processing Technology
- Vol. 164, 51-68
Open AccessCFD modelling of particle shrinkage in a fluidized bed for biomass fast pyrolysis with quadrature method of moment