Na Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Na Li has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Zhengyi Jiang
School of Mechanical, Materials, Mechatronic and Biomedical Engineering, University of Wollongong, Wollongong, Australia
6 shared publications - Hongmei Zhang
School of Materials and Metallurgy, University of Science and Technology Liaoning, Anshan 114051, China
3 shared publications - Yuchuan Zhu
School of Mechanical Engineering and Automation, University of Science and Technology Liaoning, Anshan 114051, China
3 shared publications Xuyuan Wang
Guangdong Provincial Key Laboratory of New Energy Materials Service Safety, College of Materials Science and Engineering, Shenzhen University, Shenzhen, China
2 shared publications- Yan Li
State Key Laboratory of Metal Material for Marine Equipment and Application, Anshan 114009, China
2 shared publications Zhengyi Jiang
School of Engineering University of Wollongong Wollongong New South Wales Australia
2 shared publications
Latest Publications
- 17 September 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- p. 1-13
Hot Deformation Behavior of 2205 Duplex Stainless Steel Containing Cu
- 17 September 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- p. 1-13
Hot Deformation Behavior of 2205 Duplex Stainless Steel Containing Cu
- 24 July 2026
- Published by Wiley in Steel Research International
In Situ Observation of High‐Temperature Microstructure of Cu‐Bearing 2205 Stainless Steel
The repeated recycling of scrap steel introduces and progressively enriches residual Cu in recycled stainless steels. To investigate the influence of Cu on the high‐temperature phase stability and microstructural evolution of 2205 duplex stainless steel, in situ high‐temperature observations were conducted using laser scanning confocal microscopy. The results reveal that increasing Cu content leads to a stable increase in the γ:α ratio. Meanwhile, the temperatures at which austenite transforms to ferrite initially decrease and subsequently rise with further Cu addition. This dual behavior arises because Cu enhances the thermodynamic activity of Cr, thereby promoting δ‐ferrite formation; simultaneously, Cu acts as an austenite stabilizer, and its influence on expanding the γ‐phase region becomes increasingly dominant at higher Cu concentrations. Cu addition (≤1.9 wt%) exerts a negligible influence on the liquidus temperature, which remains consistently above 1450 °C. No evidence of Cu segregation, intergranular liquation, or localized melting was observed, which indicates that Cu would not induce hot cracking susceptibility under typical processing conditions.
- 24 July 2026
- Published by Wiley in Steel Research International
In Situ Observation of High‐Temperature Microstructure of Cu‐Bearing 2205 Stainless Steel
The repeated recycling of scrap steel introduces and progressively enriches residual Cu in recycled stainless steels. To investigate the influence of Cu on the high‐temperature phase stability and microstructural evolution of 2205 duplex stainless steel, in situ high‐temperature observations were conducted using laser scanning confocal microscopy. The results reveal that increasing Cu content leads to a stable increase in the γ:α ratio. Meanwhile, the temperatures at which austenite transforms to ferrite initially decrease and subsequently rise with further Cu addition. This dual behavior arises because Cu enhances the thermodynamic activity of Cr, thereby promoting δ‐ferrite formation; simultaneously, Cu acts as an austenite stabilizer, and its influence on expanding the γ‐phase region becomes increasingly dominant at higher Cu concentrations. Cu addition (≤1.9 wt%) exerts a negligible influence on the liquidus temperature, which remains consistently above 1450 °C. No evidence of Cu segregation, intergranular liquation, or localized melting was observed, which indicates that Cu would not induce hot cracking susceptibility under typical processing conditions.
- Open Access
Preparation, Characterization, and Lubrication Performances of Water-Based Nanolubricant for Micro Rolling Strips
Water-based nanolubricants are widely used in rolling processes due to their unique characteristics. As a common additive, nanoparticles could significantly improve the tribological properties of the lubricant. However, the effect of the physical properties of the particles on the anti-friction behavior is unclear. In this study, the effect of Fe3O4 nanoparticles as an additive for the prepared lubricant is studied. The tribological properties of Fe3O4 water-based nanolubricant are examined using a tribometer and a scratch meter. The absorption energy is calculated using the molecular dynamic simulation method, and the best parameters for the preparation of the nanolubricant are obtained. The developed nanolubricant is used in the rolling process. The results show that the processing quality of samples is promoted and the tribological properties of water-based lubricant can be significantly promoted by an Fe3O4 nanoparticle additive. An economical and environmentally friendly method is presented through which the water-based Fe3O4 nanolubricant can be prepared for the replacement of oil-based lubricant in cold rolling strips.
Open AccessPreparation, Characterization, and Lubrication Performances of Water-Based Nanolubricant for Micro Rolling Strips
Water-based nanolubricants are widely used in rolling processes due to their unique characteristics. As a common additive, nanoparticles could significantly improve the tribological properties of the lubricant. However, the effect of the physical properties of the particles on the anti-friction behavior is unclear. In this study, the effect of Fe3O4 nanoparticles as an additive for the prepared lubricant is studied. The tribological properties of Fe3O4 water-based nanolubricant are examined using a tribometer and a scratch meter. The absorption energy is calculated using the molecular dynamic simulation method, and the best parameters for the preparation of the nanolubricant are obtained. The developed nanolubricant is used in the rolling process. The results show that the processing quality of samples is promoted and the tribological properties of water-based lubricant can be significantly promoted by an Fe3O4 nanoparticle additive. An economical and environmentally friendly method is presented through which the water-based Fe3O4 nanolubricant can be prepared for the replacement of oil-based lubricant in cold rolling strips.
- Open Access
- 8 October 2023
- Published by MDPI AG in Lubricants
- Vol. 11 (10) , 434
Friction and Wear Characteristics of Fe3O4 Nano-Additive Lubricant in Micro-Rolling
As nanotechnology has developed, some nano-additives have been employed to improve the performance of lubricants. The mechanisms of nano-additives still need to be investigated. The wear characteristics of Fe3O4 nano-additive lubricant were investigated in this study. Different diameters of Fe3O4 nanoparticles were mixed in basic oil using an ultrasonic mixer. The new lubricant was used for analytical tests at room temperature. The results showed that nano-lubricants with 20 nm nanoparticles increase the oil film strength. The coefficient of friction was reduced when 20 nm diameter 8 wt% Fe3O4 nanoparticles were mixed with lubricants. The effect of surfactants and nanoparticles in the base oil was measured using numerical simulation methods. The adsorption capacity of the lubricants was significantly improved by Fe3O4 nanoparticles, particularly when looking at the small relative atomic mass of the metal. The 8 wt% Fe3O4 lubricant exhibited optimal tribological properties when applied in micro-rolling tests. The results showed that the surface quality of the rolled samples was significantly improved, and the rolling force was dramatically reduced. At the same time, the shapes of the samples were effectively controlled in the rolling process. Therefore, Fe3O4 nanoparticles can improve the friction and wear characteristics of lubricants.
- 8 October 2023
- Published by MDPI AG in Lubricants
- Vol. 11 (10) , 434
Open AccessFriction and Wear Characteristics of Fe3O4 Nano-Additive Lubricant in Micro-Rolling
As nanotechnology has developed, some nano-additives have been employed to improve the performance of lubricants. The mechanisms of nano-additives still need to be investigated. The wear characteristics of Fe3O4 nano-additive lubricant were investigated in this study. Different diameters of Fe3O4 nanoparticles were mixed in basic oil using an ultrasonic mixer. The new lubricant was used for analytical tests at room temperature. The results showed that nano-lubricants with 20 nm nanoparticles increase the oil film strength. The coefficient of friction was reduced when 20 nm diameter 8 wt% Fe3O4 nanoparticles were mixed with lubricants. The effect of surfactants and nanoparticles in the base oil was measured using numerical simulation methods. The adsorption capacity of the lubricants was significantly improved by Fe3O4 nanoparticles, particularly when looking at the small relative atomic mass of the metal. The 8 wt% Fe3O4 lubricant exhibited optimal tribological properties when applied in micro-rolling tests. The results showed that the surface quality of the rolled samples was significantly improved, and the rolling force was dramatically reduced. At the same time, the shapes of the samples were effectively controlled in the rolling process. Therefore, Fe3O4 nanoparticles can improve the friction and wear characteristics of lubricants.
- 6 May 2023
- Published by Elsevier in Materials Today Communications
- Vol. 35
High-temperature oxidation behavior of 301 stainless steel containing Cu
- 6 May 2023
- Published by Elsevier in Materials Today Communications
- Vol. 35
High-temperature oxidation behavior of 301 stainless steel containing Cu
- Open Access
Effect of Copper on Microstructure and Corrosion Resistance of Hot Rolled 301 Stainless Steel
The effect of copper (Cu) on hot-rolled 301 austenitic stainless steel (ASS) was studied by observing the microstructures and testing the electrochemical corrosion resistance properties. The results showed that, with the increase in Cu content, the size of shear zones in 301 ASS decreased, and the number increased, which increased the uniformity of the microstructure macroscopically. The presence of Cu decreased the stacking fault energy of 301 ASS at elevated temperatures. Meanwhile, the amount of chromium (Cr) carbides decreased gradually with the increase in Cu content, which implies that the solid solution of Cu in hot-rolled 301 stainless steel promotes the solid solution of Cr and C in the steel, which is conducive to the formation of Cr-rich passivation films. As a result, the corrosion resistance of hot rolled Cu-bearing 301 stainless steel is improved, with both lower corrosion current density (Icorr) and passivation current (Ipass), and more positive corrosion potentials (Ecorr) and passivation potential (Ep), even though it does not show a higher pitting resistance. As Cu content in the steel was increased from 0.4% to 1.1%, the corrosion resistance was not further improved.
Open AccessEffect of Copper on Microstructure and Corrosion Resistance of Hot Rolled 301 Stainless Steel
The effect of copper (Cu) on hot-rolled 301 austenitic stainless steel (ASS) was studied by observing the microstructures and testing the electrochemical corrosion resistance properties. The results showed that, with the increase in Cu content, the size of shear zones in 301 ASS decreased, and the number increased, which increased the uniformity of the microstructure macroscopically. The presence of Cu decreased the stacking fault energy of 301 ASS at elevated temperatures. Meanwhile, the amount of chromium (Cr) carbides decreased gradually with the increase in Cu content, which implies that the solid solution of Cu in hot-rolled 301 stainless steel promotes the solid solution of Cr and C in the steel, which is conducive to the formation of Cr-rich passivation films. As a result, the corrosion resistance of hot rolled Cu-bearing 301 stainless steel is improved, with both lower corrosion current density (Icorr) and passivation current (Ipass), and more positive corrosion potentials (Ecorr) and passivation potential (Ep), even though it does not show a higher pitting resistance. As Cu content in the steel was increased from 0.4% to 1.1%, the corrosion resistance was not further improved.
- Open Access
Corrosion Behavior of Copper Bearing Steels and the Derived In-Situ Coating
Using a period immersion wet/dry cyclic corrosion test, in-situ copper-coated steels prepared by corroding copper-bearing steels were investigated in this study. The steel with a higher copper content (>3%) has a higher initial corrosion rate due to its obvious two-phase microstructure. The corrosion rates of all copper bearing steels tend to be stable after a certain time of corrosion. A copper-rich layer is formed between the matrix and the rust layer, which is due to the diffusion of copper from the rust layer to the metal surface. The copper’s stability under this corrosion condition led to the formation of a thin copper-rich film, which was uncovered after removing the rust by choosing appropriate descaling reagents. The copper coating was generated from the matrix itself during the corrosion process at 25 °C, which provided a new approach for producing in-situ composite materials without any bonding defect. It is found that the corrosion rate, corrosion time, and copper content in steel all affect the formation of copper-rich layer. In addition to the noble copper surface, the electrochemical corrosion test results show that the corrosion resistance of copper-coated steel has been significantly improved.
Open AccessCorrosion Behavior of Copper Bearing Steels and the Derived In-Situ Coating
Using a period immersion wet/dry cyclic corrosion test, in-situ copper-coated steels prepared by corroding copper-bearing steels were investigated in this study. The steel with a higher copper content (>3%) has a higher initial corrosion rate due to its obvious two-phase microstructure. The corrosion rates of all copper bearing steels tend to be stable after a certain time of corrosion. A copper-rich layer is formed between the matrix and the rust layer, which is due to the diffusion of copper from the rust layer to the metal surface. The copper’s stability under this corrosion condition led to the formation of a thin copper-rich film, which was uncovered after removing the rust by choosing appropriate descaling reagents. The copper coating was generated from the matrix itself during the corrosion process at 25 °C, which provided a new approach for producing in-situ composite materials without any bonding defect. It is found that the corrosion rate, corrosion time, and copper content in steel all affect the formation of copper-rich layer. In addition to the noble copper surface, the electrochemical corrosion test results show that the corrosion resistance of copper-coated steel has been significantly improved.
- Open Access
In-situ Cu Coating on Steel Surface after Oxidizing at High Temperature
Almost all copper in scrap steel is recovered, so research on copper-bearing steel has profound practical significance. The surface enrichment of copper occurs in all copper-bearing steels studied in this paper after being heated at high temperature. In-situ oxidation-induced copper coatings were discovered on the descaled copper-bearing steels after heating at around 1150 °C for 2 h in air. Scattered copper precipitates in or under rust after heating at a lower temperature. A new concept was created using in-situ composites prepared by direct oxidation of matrix, and there was no bonding problem found between the coating and the matrix. The enrichment form of copper in steel is related to the oxidation rate, oxidation time, heating temperature and copper content.
Open AccessIn-situ Cu Coating on Steel Surface after Oxidizing at High Temperature
Almost all copper in scrap steel is recovered, so research on copper-bearing steel has profound practical significance. The surface enrichment of copper occurs in all copper-bearing steels studied in this paper after being heated at high temperature. In-situ oxidation-induced copper coatings were discovered on the descaled copper-bearing steels after heating at around 1150 °C for 2 h in air. Scattered copper precipitates in or under rust after heating at a lower temperature. A new concept was created using in-situ composites prepared by direct oxidation of matrix, and there was no bonding problem found between the coating and the matrix. The enrichment form of copper in steel is related to the oxidation rate, oxidation time, heating temperature and copper content.