LLLinwei Liu

Linwei Liu

*This is an algorithmically generated author record based on publicly available information.

Linwei Liu has a total of 37 co-authors. Here are the top co-authors by number of shared publications:

  • Guofu Zhou

    Lab of Light and Physio-psychological Health, National Center for International Research on Green Optoelectronics, South China Normal University, Guangzhou 510006, China

    5 shared publications
  • Wei Li

    Shenzhen Guohua Optoelectronics Tech. Co., Ltd., Shenzhen 518110, China, China

    4 shared publications
  • Zichuan Yi

    School of Electronic Information, University of Electronic Science and Technology of China, Zhongshan Institute, Zhongshan 528402, China

    4 shared publications
  • Cheng Xu

    Jihua Laboratory 28 Huandao South Road 528200 Foshan Guangdong China

    3 shared publications
  • Guofu Zhou

    Institute of Electronic Paper Displays Guangdong Provincial Key Laboratory of Optical Information Materials and Technology South China

    3 shared publications
  • Jianwen Lu

    Shenzhen Guohua Optoelectronics Tech. Co., Ltd 518110 Shenzhen China

    3 shared publications

Latest Publications

  • Open Access

    Influence of Oil Viscosity on Hysteresis Effect in Electrowetting Displays Based on Simulation

    by Wei Li, Linwei Liu, Taiyuan Zhang, Lixia Tian, Li Wang, Cheng Xu, Jianwen Lu, Zichuan Yi, Guofu Zhou

    As the most promising new reflective display technology, electrowetting displays (EWDs) have the advantages of a simple structure, fast response, high contrast, and rich colors. However, due to the hysteresis effect, the grayscales of EWDs cannot be accurately controlled, which seriously restricts the industrialization process of this technology. In this paper, the oil movement process in an EWD pixel cell was simulated, and the influence of oil viscosity on the hysteresis effect was studied based on the proposed simulation model. Firstly, the cause of the hysteresis effect was analyzed through the hysteresis curve of an EWD. Then, based on the COMSOL Multiphysics simulation environment, the oil movement process in an EWD pixel cell was simulated by coupling the phase field of laminar two-phase flow and electrostatic field. Finally, based on the simulation model, the influence of oil viscosity on the hysteresis effect in an EWD pixel cell was studied. We observed that the maximum hysteresis difference in the hysteresis effect increased with the increase in oil viscosity and decreased with the decrease in oil viscosity. The oil viscosity had little effect on the maximum aperture ratio of EWD. The pixel-on response time and pixel-off response time increased with the increase in oil viscosity.

  • Open Access

    Influence of Oil Viscosity on Hysteresis Effect in Electrowetting Displays Based on Simulation

    by Wei Li, Linwei Liu, Taiyuan Zhang, Lixia Tian, Li Wang, Cheng Xu, Jianwen Lu, Zichuan Yi, Guofu Zhou

    As the most promising new reflective display technology, electrowetting displays (EWDs) have the advantages of a simple structure, fast response, high contrast, and rich colors. However, due to the hysteresis effect, the grayscales of EWDs cannot be accurately controlled, which seriously restricts the industrialization process of this technology. In this paper, the oil movement process in an EWD pixel cell was simulated, and the influence of oil viscosity on the hysteresis effect was studied based on the proposed simulation model. Firstly, the cause of the hysteresis effect was analyzed through the hysteresis curve of an EWD. Then, based on the COMSOL Multiphysics simulation environment, the oil movement process in an EWD pixel cell was simulated by coupling the phase field of laminar two-phase flow and electrostatic field. Finally, based on the simulation model, the influence of oil viscosity on the hysteresis effect in an EWD pixel cell was studied. We observed that the maximum hysteresis difference in the hysteresis effect increased with the increase in oil viscosity and decreased with the decrease in oil viscosity. The oil viscosity had little effect on the maximum aperture ratio of EWD. The pixel-on response time and pixel-off response time increased with the increase in oil viscosity.


  • Open Access

    A Novel Bistable Pixel Structure Model for Electrowetting Displays Based on Asymmetric Electric Field

    by Linwei Liu, Wei Li, Taiyuan Zhang, Lixia Tian, Li Wang, Cheng Xu, Jianwen Lu, Zichuan Yi, Guofu Zhou

    As the most potential new reflective display technology, electrowetting display (EWD) has the advantages of simple structure, fast response, high contrast and rich colors. However, the EWD is based on two fluid system, so the conventional pixel structure is difficult to achieve bistable display control. In this paper, a novel pixel structure model with upper and lower symmetry for electrowetting display devices (EWDs) was proposed. And based on an asymmetric electric field, the two fluids could be controlled to flow vertically to achieve bistable display. The model includes four independently driven electrodes, two partition strips and two oil tanks, and the distance between the upper and lower substrates is low, which can realize the stable storage of oil in the upper and lower tanks. Firstly, based on COMSOL Multiphysics simulation environment, the oil motion control in a pixel model was successfully realized by coupling the phase field and electrostatic field of laminar two-phase flow. By using the designed voltage driving sequence, the free switching between on-state and off-state could be realized to achieve bistable display control. Then, the bistable pixel structure was optimized to reduce the switching time between the upper and lower substrates. It was found that by reducing the pixel height, not only the time of oil switching between the upper and lower substrates could be reduced, but also a third steady state of pixels could be formed by using the partition strips. After the electric field was removed, there was also an energy barrier to blocking the flow of oil, giving the model the ability to form a third steady state. Finally, an accelerated driving method was proposed for this model, which could significantly improve the oil spreading speed by applying a lower voltage to the electrode where the oil is located during the spreading process. Compared with the natural spreading of oil, the whole spreading time was shortened by 33.3%.

  • Open Access

    A Novel Bistable Pixel Structure Model for Electrowetting Displays Based on Asymmetric Electric Field

    by Linwei Liu, Wei Li, Taiyuan Zhang, Lixia Tian, Li Wang, Cheng Xu, Jianwen Lu, Zichuan Yi, Guofu Zhou

    As the most potential new reflective display technology, electrowetting display (EWD) has the advantages of simple structure, fast response, high contrast and rich colors. However, the EWD is based on two fluid system, so the conventional pixel structure is difficult to achieve bistable display control. In this paper, a novel pixel structure model with upper and lower symmetry for electrowetting display devices (EWDs) was proposed. And based on an asymmetric electric field, the two fluids could be controlled to flow vertically to achieve bistable display. The model includes four independently driven electrodes, two partition strips and two oil tanks, and the distance between the upper and lower substrates is low, which can realize the stable storage of oil in the upper and lower tanks. Firstly, based on COMSOL Multiphysics simulation environment, the oil motion control in a pixel model was successfully realized by coupling the phase field and electrostatic field of laminar two-phase flow. By using the designed voltage driving sequence, the free switching between on-state and off-state could be realized to achieve bistable display control. Then, the bistable pixel structure was optimized to reduce the switching time between the upper and lower substrates. It was found that by reducing the pixel height, not only the time of oil switching between the upper and lower substrates could be reduced, but also a third steady state of pixels could be formed by using the partition strips. After the electric field was removed, there was also an energy barrier to blocking the flow of oil, giving the model the ability to form a third steady state. Finally, an accelerated driving method was proposed for this model, which could significantly improve the oil spreading speed by applying a lower voltage to the electrode where the oil is located during the spreading process. Compared with the natural spreading of oil, the whole spreading time was shortened by 33.3%.

  • Open Access

    A Novel Bistable Pixel Structure Model for Electrowetting Displays Based on Asymmetric Electric Field

    by Linwei Liu, Wei Li, Taiyuan Zhang, Lixia Tian, Li Wang, Cheng Xu, Jianwen Lu, Zichuan Yi, Guofu Zhou

    As the most potential new reflective display technology, electrowetting display (EWD) has the advantages of simple structure, fast response, high contrast and rich colors. However, the EWD is based on two fluid system, so the conventional pixel structure is difficult to achieve bistable display control. In this paper, a novel pixel structure model with upper and lower symmetry for electrowetting display devices (EWDs) was proposed. And based on an asymmetric electric field, the two fluids could be controlled to flow vertically to achieve bistable display. The model includes four independently driven electrodes, two partition strips and two oil tanks, and the distance between the upper and lower substrates is low, which can realize the stable storage of oil in the upper and lower tanks. Firstly, based on COMSOL Multiphysics simulation environment, the oil motion control in a pixel model was successfully realized by coupling the phase field and electrostatic field of laminar two-phase flow. By using the designed voltage driving sequence, the free switching between on-state and off-state could be realized to achieve bistable display control. Then, the bistable pixel structure was optimized to reduce the switching time between the upper and lower substrates. It was found that by reducing the pixel height, not only the time of oil switching between the upper and lower substrates could be reduced, but also a third steady state of pixels could be formed by using the partition strips. After the electric field was removed, there was also an energy barrier to blocking the flow of oil, giving the model the ability to form a third steady state. Finally, an accelerated driving method was proposed for this model, which could significantly improve the oil spreading speed by applying a lower voltage to the electrode where the oil is located during the spreading process. Compared with the natural spreading of oil, the whole spreading time was shortened by 33.3%.

  • Open Access

    Design of Multi-DC Overdriving Waveform of Electrowetting Displays for Gray Scale Consistency

    by Yijian Xu, Shixiao Li, Ziyang Wang, Heng Zhang, Zikai Li, Bo Xiao, Wei Guo, Linwei Liu, Pengfei Bai

    Gray scale consistency in pixels was extremely important for electrowetting displays (EWDs). However, traditional electrowetting display driving waveforms could not obtain a pixel aperture ratio consistency, which led to the occurrence of gray inconsistency even if it was the same driving waveform. In addition, the oil backflow caused by charge trapping could not be sustained. Therefore, a multi-direct current (DC) overdriving waveform for gray scale consistency was proposed in this paper, which could effectively improve the performance of EWDs. The driving waveform was divided into a start-up driving phase and a stable driving phase. The stable driving phase was composed of a square wave with a duty cycle of 79% and a frequency of 43 Hz. Subsequently, an overdriving pulse was also introduced in the stable driving phase. The multi-DC driving waveform for gray scale consistency was applied to a thin film transistor-electrowetting display (TFT-EWD). The average difference between increasing driving voltage and decreasing driving voltage was only 2.79%. The proposed driving waveform has an aperture ratio of 3.7 times at low voltages compared to DC driving.


  • Open Access

    Dynamic Adaptive Display System for Electrowetting Displays Based on Alternating Current and Direct Current

    by Shixiao Li, Yijian Xu, Zhiyu Zhan, Pengyuan Du, Linwei Liu, Zikai Li, Huawei Wang, Pengfei Bai

    As a representative of the new reflective display technology, electrowetting display (EWD) technology can be used as a video playback display device due to its fast response characteristics. Direct current (DC) driving brings excellent reflectivity, but static images cannot be displayed continually due to charge trapping, and it can cause afterimages when playing a dynamic video due to contact angle hysteresis. Alternating current (AC) driving brings a good dynamic video refresh ability to EWDs, but that can cause flickers. In this paper, a dynamic adaptive display model based on thin film transistor-electrowetting display (TFT-EWD) was proposed. According to the displayed image content, the TFT-EWD display driver was dynamically adjusted by AC and DC driving models. A DC hybrid driving model was suitable for static image display, which could effectively suppress oil backflow and achieve static image display while ensuring high reflectivity. A source data non-polarized model (SNPM) is an AC driving model which was suitable for dynamic video display and was proposed at the same time. Compared with DC driving, it could obtain smooth display performance with a loss of about 10 absorbance units (A.U.) of reflective luminance, which could solve the flicker problem. With the DC hybrid driving model, the ability to continuously display static images could be obtained with a loss of 2 (A.U.) of luminance. Under the AC driving in SNPM, the reflected luminance was as high as 67 A.U., which was 8 A.U. higher than the source data polarized model (SPM), and it was closer to the reflected luminance under DC driving.


  • Open Access

    A Separated Reset Waveform Design for Suppressing Oil Backflow in Active Matrix Electrowetting Displays

    by Linwei Liu, Pengfei Bai, Zichuan Yi, Guofu Zhou

    The electrowetting display (EWD) is a kind of reflective paper-like display. Flicker and grayscale distortion are caused by oil backflow, which is one of the important factors restricting the wide application of EWDs. The charge embedding caused by the electric field force in the dielectric layer is the cause of oil backflow. To suppress oil backflow, a separated reset waveform based on the study of oil movement is proposed in this paper. The driving waveform is divided into two parts: a reset waveform and a grayscale waveform. The reset waveform generated by a reset circuit can be used to output various voltages. The grayscale waveform is set as a traditional PWM waveform. The reset waveform is composed of a charge-releasing stage and oil-moving back stage. Two phases are contained in the charge releasing stage. The overdriving voltage is used during the first phase to reverse the voltage of all pixels. The trapped charges can then be released from the dielectric layer during the second phase. A higher voltage is used during the oil-moving back stage to drive the oil faster in the pixel. By comparing the experimental data, the oil backflow time is extended 761 times by the reset waveform. The four grayscales can be maintained by the reset waveform after driving for 300 s.


  • Open Access

    Progress in Advanced Properties of Electrowetting Displays

    by Yi Lu, Biao Tang, Guisong Yang, Yuanyuan Guo, Linwei Liu, Alex Henzen

    Electrowetting display (EWD) has promising prospects in the electronic paper industry due to it having superior characteristics, such as the ability to provide a comfortable reading experience and quick response. However, in real applications, there are also problems related to dielectric deterioration, excess power consumption, optical instability and narrow color gamut etc. This paper reviewed the existing challenges and recent progress made in terms of improving the optical performance and reliability of EWD. First, the principle of electrowetting applied in small and confined configurations is introduced and the cause of the failure of the dielectric layer is analyzed. Then, the function of the pixel structures is described to avoid display defects. Next, electric signal modulations are compared in terms of achieving good image quality and optical stability. Lastly, the methods are presented for color panel realization. It was concluded that multi-layer dielectrics, three-dimensional pixel structures, proper electric frequency-and-amplitude modulation and an RGB color panel are expected to resolve the current limitations and contribute to designing advanced reflective displays.


  • Open Access

    Driving Waveform Design with Rising Gradient and Sawtooth Wave of Electrowetting Displays for Ultra-Low Power Consumption

    by Wei Li, Li Wang, Taiyuan Zhang, Shufa Lai, Linwei Liu, Wenyao He, Guofu Zhou, Zichuan Yi

    As a kind of paper-like display technology, power consumption is a very important index for electrowetting displays (EWDs). In this paper, the influence of driving waveforms on power consumption of the EWDs is analyzed, and a driving waveform with rising gradient and sawtooth wave is designed to reduce the power consumption. There are three stages in the proposed driving waveform. In the initial stage, the driving voltage is raised linearly from the threshold to the maximum value to reduce the invalid power consumption. At the same time, the oil breakup can be prohibited. And then, a section of sawtooth wave is added for suppressing oil backflow. Finally, there is a section of resetting wave to eliminate the influence of charge leakage. Experimental results show that the power consumption of the ultra-low power driving waveform is 1.85 mW, which is about 38.13% lower than that of the conventional used square wave (2.99 mW), when the aperture ratio is 65%.