Wei Li has a total of 30 co-authors. Here are the top co-authors by number of shared publications:

  • Guofu Zhou

    Lab of Light and Physio-psychological Health, National Center for International Research on Green Optoelectronics, South China Normal University, Guangzhou 510006, China

    7 shared publications
  • Taiyuan Zhang

    Guangdong Provincial Key Laboratory of Optical Information Materials and Technology & Institute of Electronic Paper Displays, South China Academy of Advanced Optoelectronics, South China Normal University, Guangzhou 510006, China, China

    6 shared publications
  • Li Wang

    School of Information Engineering, Zhongshan Polytechnic, Zhongshan 528400, China, China

    4 shared publications
  • Linwei Liu

    School of Information Engineering, Zhongshan Polytechnic, Zhongshan 528400, China, China

    4 shared publications
  • Zichuan Yi

    School of Electronic Information, University of Electronic Science and Technology of China, Zhongshan Institute, Zhongshan 528402, China

    4 shared publications
  • Cheng Xu

    Jihua Laboratory, 28 Huandao South Road, Foshan, Guangdong 528200, China, China

    2 shared publications

Latest Publications

  • Open Access

    Influence of Oil Viscosity on Hysteresis Effect in Electrowetting Displays Based on Simulation

    by Wei Li, Linwei Liu, Taiyuan Zhang, Lixia Tian, Li Wang, Cheng Xu, Jianwen Lu, Zichuan Yi, Guofu Zhou

    As the most promising new reflective display technology, electrowetting displays (EWDs) have the advantages of a simple structure, fast response, high contrast, and rich colors. However, due to the hysteresis effect, the grayscales of EWDs cannot be accurately controlled, which seriously restricts the industrialization process of this technology. In this paper, the oil movement process in an EWD pixel cell was simulated, and the influence of oil viscosity on the hysteresis effect was studied based on the proposed simulation model. Firstly, the cause of the hysteresis effect was analyzed through the hysteresis curve of an EWD. Then, based on the COMSOL Multiphysics simulation environment, the oil movement process in an EWD pixel cell was simulated by coupling the phase field of laminar two-phase flow and electrostatic field. Finally, based on the simulation model, the influence of oil viscosity on the hysteresis effect in an EWD pixel cell was studied. We observed that the maximum hysteresis difference in the hysteresis effect increased with the increase in oil viscosity and decreased with the decrease in oil viscosity. The oil viscosity had little effect on the maximum aperture ratio of EWD. The pixel-on response time and pixel-off response time increased with the increase in oil viscosity.

  • Open Access

    Influence of Oil Viscosity on Hysteresis Effect in Electrowetting Displays Based on Simulation

    by Wei Li, Linwei Liu, Taiyuan Zhang, Lixia Tian, Li Wang, Cheng Xu, Jianwen Lu, Zichuan Yi, Guofu Zhou

    As the most promising new reflective display technology, electrowetting displays (EWDs) have the advantages of a simple structure, fast response, high contrast, and rich colors. However, due to the hysteresis effect, the grayscales of EWDs cannot be accurately controlled, which seriously restricts the industrialization process of this technology. In this paper, the oil movement process in an EWD pixel cell was simulated, and the influence of oil viscosity on the hysteresis effect was studied based on the proposed simulation model. Firstly, the cause of the hysteresis effect was analyzed through the hysteresis curve of an EWD. Then, based on the COMSOL Multiphysics simulation environment, the oil movement process in an EWD pixel cell was simulated by coupling the phase field of laminar two-phase flow and electrostatic field. Finally, based on the simulation model, the influence of oil viscosity on the hysteresis effect in an EWD pixel cell was studied. We observed that the maximum hysteresis difference in the hysteresis effect increased with the increase in oil viscosity and decreased with the decrease in oil viscosity. The oil viscosity had little effect on the maximum aperture ratio of EWD. The pixel-on response time and pixel-off response time increased with the increase in oil viscosity.


  • Open Access

    Optimizing Bipolar Reset Waveform to Improve Grayscale Stability in Active Matrix Electrowetting Displays

    by Taiyuan Zhang, Li Wang, Linwei Liu, Wei Li, Shipeng Wu, Jianyang Guo, Guofu Zhou

    The electrowetting display (EWD) device is a new type of electrowetting-on-dielectric (EWOD) equipment that can achieve a paper-like display effect under the control of an electric field. In this microfluidic system, the stability of grayscale can be affected by various factors, such as the physicochemical properties of the materials, the device structure, and electric field distribution. To improve the grayscale stability of active matrix electrowetting displays (AM-EWDs), the impact of different polarities of driving voltage on oil backflow was investigated in this study. Based on the driving principles of AM-EWD, an optimized inter-frame bipolar reset driving waveform was designed to overcome oil backflow. The proposed driving waveform maintained the stability of the oil state by periodically and rapidly releasing trapped charges in the dielectric layer through a reverse driving voltage. Additionally, the effect of feed-through voltage on pixel driving voltage was eliminated by compensating for the driving voltage on a common electrode. Finally, the performance of the designed driving waveform was evaluated with a 6-inch AM-EWD driving platform. Compared to the conventional unipolar reset driving waveform, the backflow speed decreased by 2.70 a.u./s. The standard deviation of the display luminance was also reduced by 11.24 a.u. Experimental results indicated that both the oil backflow speed and the fluctuation range of luminance were effectively suppressed by the proposed driving waveform.


  • Open Access

    A Multi-Electrode Pixel Structure for Quick-Response Electrowetting Displays

    by Lixia Tian, Shufa Lai, Taiyuan Zhang, Wei Li, Biao Tang, Guofu Zhou

    A new reflective display technology, the electrowetting display (EWD), has the advantages of high contrast ratio, high reflectivity, and ultralow power consumption. The response speed of EWDs has an important influence on optical performance, and pixel structure is one of the key factors affecting the response speed of EWDs. In order to improve the response speed, a new multi-electrode pixel structure is proposed in this paper. This structure was realized by dividing the pixel into four square-shaped sub-electrodes, and a three-dimensional EWD simulation model was established. In this model, a driving voltage was first applied to one of these sub-electrodes, and the oil was ruptured. Then, its two adjacent sub-electrodes were also supplied with driving voltages, so as to spur the oil to move to a pixel corner quickly. Simulation results showed that the response speed of EWDs can be effectively improved by using the proposed multi-electrode pixel structure. Compared with a single-electrode pixel structure, the oil rupture response time of the multi-electrode pixel structure was advanced by 0.6 ms. The pixel achieved a 2.7 ms faster response time than the single-electrode pixel for reaching a 50% aperture ratio in an opening process, and the maximum aperture ratio was increased by 6.2%.


  • Open Access

    Driving Scheme Optimization for Electrowetting Displays Based on Contact Angle Hysteresis to Achieve Precise Gray-Scales

    by Li Wang, Hu Zhang, Wei Li, Jiaxuan Li, Zhenyu Yi, Qiming Wan, Jitao Zhang, Pengchang Ma

    As a new display technology, electrowetting display (EWD) has many excellent display characteristics, such as paper-like, low power consumption, quick response and full color. These characteristics make EWD devices very suitable for portable devices. However, the gray-scale distortion caused by the contact angle hysteresis of EWDs seriously affects the accuracy of gray-scale display. To improve this phenomenon, the hysteresis curve of an EWD panel was studied according to the motion characteristics of advancing contact angle and receding contact angle of oil in a pixel. Then, a driving scheme for EWDs using alternating current (AC) voltage instead of direct current (DC) voltage was proposed in this paper. And the advantages and disadvantages of the driving scheme at different AC frequencies from 90 to 2,700 Hz were analyzed through experiments. According to the stability of aperture ratio in EWDs, a 470 Hz AC driving scheme was determined. Experimental results showed that the aperture ratio distortion of EWDs could be reduced from 35.82 to 5.97%, which significantly improved the display performance of pixel units.


  • Open Access

    Driving Waveform Design of Electrophoretic Display Based on Optimized Particle Activation for a Rapid Response Speed

    by Wenyao He, Zichuan Yi, Shitao Shen, Zhenyu Huang, Linwei Liu, Taiyuan Zhang, Wei Li, Li Wang, Lingling Shui, Chongfu Zhang, et al.

    Electrophoretic displays (EPDs) have excellent paper-like display features, but their response speed is as long as hundreds of milliseconds. This is particularly important when optimizing the driving waveform for improving the response speed. Hence, a driving waveform design based on the optimization of particle activation was proposed by analyzing the electrophoresis performance of particles in EPD pixels. The particle activation in the driving waveform was divided into two phases: the improving particle activity phase and the uniform reference grayscale phase. First, according to the motion characteristics of particles in improving the particle activity phase, the real-time EPD brightness value can be obtained by an optical testing device. Secondly, the derivative of the EPD brightness curve was used to obtain the inflection point, and the inflection point was used as the duration of improving particle activity phase. Thirdly, the brightness curve of the uniform reference grayscale phase was studied to set the driving duration for obtaining a white reference grayscale. Finally, a set of four-level grayscale driving waveform was designed and validated in a commercial E-ink EPD. The experimental results showed that the proposed driving waveform can cause a reduction by 180 ms in improving particle activity phase and 120 ms in uniform reference grayscale phase effectively, and a unified reference grayscale can be achieved in uniform reference grayscale phase at the same time.


  • Open Access

    Driving Waveform Design with Rising Gradient and Sawtooth Wave of Electrowetting Displays for Ultra-Low Power Consumption

    by Wei Li, Li Wang, Taiyuan Zhang, Shufa Lai, Linwei Liu, Wenyao He, Guofu Zhou, Zichuan Yi

    As a kind of paper-like display technology, power consumption is a very important index for electrowetting displays (EWDs). In this paper, the influence of driving waveforms on power consumption of the EWDs is analyzed, and a driving waveform with rising gradient and sawtooth wave is designed to reduce the power consumption. There are three stages in the proposed driving waveform. In the initial stage, the driving voltage is raised linearly from the threshold to the maximum value to reduce the invalid power consumption. At the same time, the oil breakup can be prohibited. And then, a section of sawtooth wave is added for suppressing oil backflow. Finally, there is a section of resetting wave to eliminate the influence of charge leakage. Experimental results show that the power consumption of the ultra-low power driving waveform is 1.85 mW, which is about 38.13% lower than that of the conventional used square wave (2.99 mW), when the aperture ratio is 65%.


  • Open Access

    A Driving System for Fast and Precise Gray-Scale Response Based on Amplitude–Frequency Mixed Modulation in TFT Electrowetting Displays

    by Zichuan Yi, Linwei Liu, Li Wang, Wei Li, Lingling Shui, Guofu Zhou

    The gray-scale display which is driven by PWM (pulse width modulation) in TFT (thin film transistor) electrowetting displays (EWDs) has some shortcomings, such as large amplitude of oil oscillation in pixels and slow response speed for displaying gray scale. In this paper, an amplitude–frequency mixed modulation driving system is proposed to improve the response speed of driving gray scale and enhance the oil stability when the gray scale is displayed. In the initial stage of the driving process, the oil is driven by a high voltage to close to the target luminance, and the driving voltage is then decreased to stabilize the oil. The electrowetting hysteresis curve was used to calculate the relation model between the driving voltage and the luminance of the pixel in the system, and the driving voltage value of the pixel at each driving stage was then set to make the oil precisely and rapidly stabilize at the target luminance value. In the output driving platform, the amplitude–frequency mixed modulation is realized based on the source IC, which was used to realize digital-to-analog conversion. An 8 inch EWD was tested using an Admesy colorimeter, and the experimental results show that the pixel response time is reduced by 70% and the gray-scale oscillation is reduced by 80%.