Gerard Gandon-Ros
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gerard Gandon-Ros has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Ignacio Aracil
Department of Chemical Engineering, University of Alicante, P.O. Box 99, E-03080 Alicante, Spain
5 shared publications - Juan Antonio Conesa
Department of Chemical Engineering, University of Alicante, P.O. Box 99, E-03080 Alicante, Spain
4 shared publications María Francisca Gómez-Rico
Institute of Chemical Process Engineering, University of Alicante, P.O. Box 99, E-03080, Alicante, Spain; Department of Chemical Engineering, University of Alicante, P.O. Box 99, E-03080, Alicante, Spain
3 shared publicationsAurora Soler
2 shared publications- Maria Francisca Gomez-Rico
Department of Chemical Engineering, University of Alicante, P.O. Box 99, E-03080 Alicante, Spain
2 shared publications Ignacio Aracil
Institute of Chemical Process Engineering, University of Alicante, P.O. Box 99, E-03080 Alicante, Spain
1 shared publication
Latest Publications
- Open Access
Debromination of Waste Circuit Boards by Reaction in Solid and Liquid Phases: Phenomenological Behavior and Kinetics
The debromination of waste circuit boards (WCBs) used in computer motherboards and components has been studied with two different pieces of equipment. Firstly, the reaction of small particles (around one millimeter in diameter) and larger pieces obtained from WCBs was carried out with several solutions of K2CO3 in small non-stirred batch reactors at 200–225 °C. The kinetics of this heterogeneous reaction has been studied considering both the mass transfer and chemical reaction steps, concluding that the chemical step is much slower than diffusion. Additionally, similar WCBs were debrominated using a planetary ball mill and solid reactants, namely calcined CaO, marble sludge, and calcined marble sludge. A kinetic model has been applied to this reaction, finding that an exponential model is able to explain the results quite satisfactorily. The activity of the marble sludge is about 13% of that of pure CaO and is increased to 29% when slightly calcinating its calcite at only 800 °C for 2 h.
Open AccessDebromination of Waste Circuit Boards by Reaction in Solid and Liquid Phases: Phenomenological Behavior and Kinetics
The debromination of waste circuit boards (WCBs) used in computer motherboards and components has been studied with two different pieces of equipment. Firstly, the reaction of small particles (around one millimeter in diameter) and larger pieces obtained from WCBs was carried out with several solutions of K2CO3 in small non-stirred batch reactors at 200–225 °C. The kinetics of this heterogeneous reaction has been studied considering both the mass transfer and chemical reaction steps, concluding that the chemical step is much slower than diffusion. Additionally, similar WCBs were debrominated using a planetary ball mill and solid reactants, namely calcined CaO, marble sludge, and calcined marble sludge. A kinetic model has been applied to this reaction, finding that an exponential model is able to explain the results quite satisfactorily. The activity of the marble sludge is about 13% of that of pure CaO and is increased to 29% when slightly calcinating its calcite at only 800 °C for 2 h.
- Open Access
- 13 July 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (29) , 25422-25432
Debromination and Reusable Glass Fiber Recovery from Large Waste Circuit Board Pieces in Subcritical Water Treatment
The great economic, social, and environmental interest that favors an effective management of the recycling of waste printed circuit boards (WCBs) encourages research on the improvement of processes capable of mitigating their harmful effects. In this work, the debromination of large WCBs was first performed through a hydrothermal process employing potassium carbonate as an additive. A total of 32 runs were carried out at 225 degrees C, various CO32-/Br- anionic ratios of 1:1, 2:1, 4:1, and 6:1, treatment times from 30 to 360 min, proportion of submerged WCBs in the liquid of 100, 50, and 25% that corresponded with the use of three WCB sizes of 20 mm x 16.5 mm, 20 mm x 33 mm, and 80 mm x 33 mm, respectively, and solid/liquid ratios of 1:2 and 1:1 g/mL without other metallic catalysts. A debromination efficiency of 50 wt % was reached at only 225 degrees C (limited by mechanical reasons) and 360 min, using a CO32-/Br- anionic ratio of 4:1 and a solid/liquid ratio of 1:2 for a large WCB with only 25% of its volume submerged in the liquid. This means conservation of water and energy compared to previous studies. A muffle furnace was used later to thermally treat a total of 101 debrominated samples, at constant temperature or following a temperature scaling program. An estimated decrease in resistance to rupture of glass fibers of only around 50% was accomplished by following a temperature scaling program up to 475 degrees C, obtaining clean glass fibers of large size. The simple techniques proposed to obtain reusable glass fibers from WCBs as large as the size of the reactor allows (as it might be in their original size) could significantly improve interest in the industry.
- 13 July 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (29) , 25422-25432
Open AccessDebromination and Reusable Glass Fiber Recovery from Large Waste Circuit Board Pieces in Subcritical Water Treatment
The great economic, social, and environmental interest that favors an effective management of the recycling of waste printed circuit boards (WCBs) encourages research on the improvement of processes capable of mitigating their harmful effects. In this work, the debromination of large WCBs was first performed through a hydrothermal process employing potassium carbonate as an additive. A total of 32 runs were carried out at 225 degrees C, various CO32-/Br- anionic ratios of 1:1, 2:1, 4:1, and 6:1, treatment times from 30 to 360 min, proportion of submerged WCBs in the liquid of 100, 50, and 25% that corresponded with the use of three WCB sizes of 20 mm x 16.5 mm, 20 mm x 33 mm, and 80 mm x 33 mm, respectively, and solid/liquid ratios of 1:2 and 1:1 g/mL without other metallic catalysts. A debromination efficiency of 50 wt % was reached at only 225 degrees C (limited by mechanical reasons) and 360 min, using a CO32-/Br- anionic ratio of 4:1 and a solid/liquid ratio of 1:2 for a large WCB with only 25% of its volume submerged in the liquid. This means conservation of water and energy compared to previous studies. A muffle furnace was used later to thermally treat a total of 101 debrominated samples, at constant temperature or following a temperature scaling program. An estimated decrease in resistance to rupture of glass fibers of only around 50% was accomplished by following a temperature scaling program up to 475 degrees C, obtaining clean glass fibers of large size. The simple techniques proposed to obtain reusable glass fibers from WCBs as large as the size of the reactor allows (as it might be in their original size) could significantly improve interest in the industry.
- Open Access
- 29 May 2022
- Published by Elsevier in Journal of Environmental Management
- Vol. 317, 115431
Mechanochemical debromination of waste printed circuit boards with marble sludge in a planetary ball milling process
- 29 May 2022
- Published by Elsevier in Journal of Environmental Management
- Vol. 317, 115431
Open AccessMechanochemical debromination of waste printed circuit boards with marble sludge in a planetary ball milling process
- Open Access
- 1 October 2021
- Published by Elsevier in Journal of Cleaner Production
- Vol. 319
Improving efficiency and feasibility of subcritical water debromination of printed circuit boards E-waste via potassium carbonate adding
- 1 October 2021
- Published by Elsevier in Journal of Cleaner Production
- Vol. 319
Open AccessImproving efficiency and feasibility of subcritical water debromination of printed circuit boards E-waste via potassium carbonate adding
- Open Access
A Win–Win Combination to Inhibit Persistent Organic Pollutant Formation via the Co-Incineration of Polyvinyl Chloride E-Waste and Sewage Sludge
Persistent organic pollutant inhibition in the combustion process of polyvinyl chloride (PVC) by prior addition of an inhibitor is currently being studied, reducing the emission of pollutants, and thus reducing the large amount of waste PVC destined for landfill. In this work, the use of sewage sludge (SS) as an alternative to chemical inhibitors to improve the quality emissions of the incineration of polyvinyl chloride waste (PVC e-waste) was studied and optimized. Different combustion runs were carried out at 850 °C in a laboratory tubular reactor, varying both the molar ratio Ri (0.25, 0.50, 0.75) between inhibitors (N + S) and chlorine (Cl) and the oxygen ratio λ (0.15, 0.50) between actual oxygen and stoichiometric oxygen. The emissions of several semivolatile compounds families such as polycyclic aromatic hydrocarbons (PAHs), polychlorobenzenes (ClBzs), and polychlorophenols (ClPhs), with special interest in the emissions of the most toxic compounds, i.e., polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (dl-PCBs), were analyzed. A notable decrease in PCDD/F and dl-PCB formation was achieved in most of the experiments, especially for those runs performed under an oxygen-rich atmosphere (λ = 0.50), where the addition of sludge was beneficial with inhibition ratios Ri ≥ 0.25. An inhibition ratio of 0.75 showed the best results with almost a 100% reduction in PCDD/F formation and a 95% reduction in dl-PCB formation.
Open AccessA Win–Win Combination to Inhibit Persistent Organic Pollutant Formation via the Co-Incineration of Polyvinyl Chloride E-Waste and Sewage Sludge
Persistent organic pollutant inhibition in the combustion process of polyvinyl chloride (PVC) by prior addition of an inhibitor is currently being studied, reducing the emission of pollutants, and thus reducing the large amount of waste PVC destined for landfill. In this work, the use of sewage sludge (SS) as an alternative to chemical inhibitors to improve the quality emissions of the incineration of polyvinyl chloride waste (PVC e-waste) was studied and optimized. Different combustion runs were carried out at 850 °C in a laboratory tubular reactor, varying both the molar ratio Ri (0.25, 0.50, 0.75) between inhibitors (N + S) and chlorine (Cl) and the oxygen ratio λ (0.15, 0.50) between actual oxygen and stoichiometric oxygen. The emissions of several semivolatile compounds families such as polycyclic aromatic hydrocarbons (PAHs), polychlorobenzenes (ClBzs), and polychlorophenols (ClPhs), with special interest in the emissions of the most toxic compounds, i.e., polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (dl-PCBs), were analyzed. A notable decrease in PCDD/F and dl-PCB formation was achieved in most of the experiments, especially for those runs performed under an oxygen-rich atmosphere (λ = 0.50), where the addition of sludge was beneficial with inhibition ratios Ri ≥ 0.25. An inhibition ratio of 0.75 showed the best results with almost a 100% reduction in PCDD/F formation and a 95% reduction in dl-PCB formation.
- 1 February 2020
- Published by Elsevier in Waste Management
- Vol. 102, 204-211
Dechlorination of polyvinyl chloride electric wires by hydrothermal treatment using K2CO3 in subcritical water
- 1 February 2020
- Published by Elsevier in Waste Management
- Vol. 102, 204-211
Dechlorination of polyvinyl chloride electric wires by hydrothermal treatment using K2CO3 in subcritical water