Surapaneni Srinivasa Rao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Surapaneni Srinivasa Rao has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Prabhakara Rao Ganji
Department of Mechanical Engineering, Gudlavalleru Engineering College, Andhra Pradesh, 521356, India
11 shared publications - Siva Prasad Kattela
GMR Institute of Technology
7 shared publications G. Naga Srinivasulu
Department of Mechanical Engineering National Institute of Technology Warangal Warangal Telangana India
5 shared publications- Muralikrishna Boni
Department of Mechanical Engineering Maharaj Vijayaram Gajapathi Raj College of Engineering Vizianagaram Andhra Pradesh India
3 shared publications Srinivasa Reddy Badduri
3 shared publicationsV. R. K. Raju
Department of Mechanical Engineering, NIT
3 shared publications
Latest Publications
- 7 February 2026
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (4) , 3321-3342
Experimental investigations on fire characteristics of mineral transformer oil
- 7 February 2026
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (4) , 3321-3342
Experimental investigations on fire characteristics of mineral transformer oil
- Open Access
- 1 January 2026
- Published by Wiley in International Journal of Energy Research
- Vol. 2026 (1)
Butanol–Diesel Blends in Compression Ignition Engines: A Comprehensive Review of Fuel Properties, Combustion, Performance, Emissions, and Optimization
The growing concerns regarding fossil fuel depletion, volatile petroleum prices, and increasingly stringent emission regulations have intensified research on renewable fuels for compression ignition (CI) engines. Among alcohol‐based biofuels, butanol has emerged as a promising alternative because of its favorable physicochemical properties, including higher energy density, lower hygroscopicity, and better compatibility with diesel compared with lower‐chain alcohols such as methanol and ethanol. This review critically examines the application of butanol in CI engines by consolidating recent experimental and numerical investigations. The review covers fuel properties, blending strategies, combustion characteristics, engine performance, engine parameters, and dual‐fuel operating modes. Particular attention is given to the influence of butanol concentration and operating conditions on brake thermal efficiency, fuel consumption, nitrogen oxides, soot, carbon monoxide, and unburned hydrocarbon emissions. The analysis reveals that butanol–diesel blends can provide a favorable balance between combustion efficiency and emission reduction, although the extent of improvement depends strongly on engine configuration and optimization of operating parameters. By integrating findings from diverse studies, this work identifies current research trends, highlights unresolved challenges related to ignition behavior and fuel economy, and outlines future directions for the effective utilization of butanol in CI engines. The review demonstrates that butanol is a viable renewable fuel candidate capable of supporting cleaner and more efficient diesel‐engine operation.
- 1 January 2026
- Published by Wiley in International Journal of Energy Research
- Vol. 2026 (1)
Open AccessButanol–Diesel Blends in Compression Ignition Engines: A Comprehensive Review of Fuel Properties, Combustion, Performance, Emissions, and Optimization
The growing concerns regarding fossil fuel depletion, volatile petroleum prices, and increasingly stringent emission regulations have intensified research on renewable fuels for compression ignition (CI) engines. Among alcohol‐based biofuels, butanol has emerged as a promising alternative because of its favorable physicochemical properties, including higher energy density, lower hygroscopicity, and better compatibility with diesel compared with lower‐chain alcohols such as methanol and ethanol. This review critically examines the application of butanol in CI engines by consolidating recent experimental and numerical investigations. The review covers fuel properties, blending strategies, combustion characteristics, engine performance, engine parameters, and dual‐fuel operating modes. Particular attention is given to the influence of butanol concentration and operating conditions on brake thermal efficiency, fuel consumption, nitrogen oxides, soot, carbon monoxide, and unburned hydrocarbon emissions. The analysis reveals that butanol–diesel blends can provide a favorable balance between combustion efficiency and emission reduction, although the extent of improvement depends strongly on engine configuration and optimization of operating parameters. By integrating findings from diverse studies, this work identifies current research trends, highlights unresolved challenges related to ignition behavior and fuel economy, and outlines future directions for the effective utilization of butanol in CI engines. The review demonstrates that butanol is a viable renewable fuel candidate capable of supporting cleaner and more efficient diesel‐engine operation.
- 13 December 2023
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 146 (2) , 1-17
Effect of Deflector on the Combustion Characteristics of a Micro-Combustor With a Controlled Centrally Slotted Bluff Body
Flame tip-opening in a micro-combustor with a controlled centrally slotted bluff body adversely affects the combustion characteristics, leading to reduced average combustion efficiency and exhaust gas temperature. To minimize the adverse effects of the flame tip-opening, a deflector is introduced in the micro-combustor, downstream to the bluff body, and its effect on various combustion parameters is studied. The insertion of a deflector significantly increases the exhaust gas temperatures in the central region by establishing a secondary flame root. However, sudden changes in the flow direction caused by the insertion of deflector induce a sudden expansion-compression strain on the flame front, thereby slightly reducing the temperature of the flame zones on either side of the central region. A downstream shift in the position of the deflector marginally mitigates the adverse effects of sudden expansion-compression strain on the exhaust gas temperature, as they are induced within the secondary reaction flame zones. On the other hand, the downstream shift of the deflector negatively impacts the exhaust gas temperature in the central region due to the reduced length available for near-complete combustion downstream of the secondary flame root. In conclusion, the deflector positioned farther from the outlet is found to result in better overall combustion characteristics at higher controllable flow ratios.
- 13 December 2023
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 146 (2) , 1-17
Effect of Deflector on the Combustion Characteristics of a Micro-Combustor With a Controlled Centrally Slotted Bluff Body
Flame tip-opening in a micro-combustor with a controlled centrally slotted bluff body adversely affects the combustion characteristics, leading to reduced average combustion efficiency and exhaust gas temperature. To minimize the adverse effects of the flame tip-opening, a deflector is introduced in the micro-combustor, downstream to the bluff body, and its effect on various combustion parameters is studied. The insertion of a deflector significantly increases the exhaust gas temperatures in the central region by establishing a secondary flame root. However, sudden changes in the flow direction caused by the insertion of deflector induce a sudden expansion-compression strain on the flame front, thereby slightly reducing the temperature of the flame zones on either side of the central region. A downstream shift in the position of the deflector marginally mitigates the adverse effects of sudden expansion-compression strain on the exhaust gas temperature, as they are induced within the secondary reaction flame zones. On the other hand, the downstream shift of the deflector negatively impacts the exhaust gas temperature in the central region due to the reduced length available for near-complete combustion downstream of the secondary flame root. In conclusion, the deflector positioned farther from the outlet is found to result in better overall combustion characteristics at higher controllable flow ratios.
- 5 December 2022
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 48 (14) , 5696-5707
Numerical investigation of the effect of slit-width on the combustion characteristics of a micro-combustor with a centrally slotted bluff body
- 5 December 2022
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 48 (14) , 5696-5707
Numerical investigation of the effect of slit-width on the combustion characteristics of a micro-combustor with a centrally slotted bluff body
- 4 August 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 237 (3) , 917-927
Numerical investigation of the effect of the slit profile on the combustion characteristics of a micro-combustor with a centrally slotted bluff body
Numerical studies are performed on a micro-combustor with a centrally slotted bluff body by varying the slit profile. The slit profiles is modified to alter the velocity of the fluid stream through the slit. Three different slit profiles are considered viz., straight, converging and diverging slits. The combustion characteristics are evaluated in terms of the hydrogen combustion efficiency, combustion progress parameter and blow-off limits. The converging slit is found to exhibit better combustion efficiency compared to the other two slit profiles. The converging slit resulted in the formation of a secondary recirculation zone near the rear end of the bluff body. A novel approach towards understanding the flame splitting which finally results in blow-off is presented. Total viscosity is considered as the means to quantify the shear stress which is responsible for the flame stretching and eventual flame splitting. It is observed that the flame blows off at smaller inlet velocities in the combustor with the converging slit compared to the other slit profiles.
- 4 August 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 237 (3) , 917-927
Numerical investigation of the effect of the slit profile on the combustion characteristics of a micro-combustor with a centrally slotted bluff body
Numerical studies are performed on a micro-combustor with a centrally slotted bluff body by varying the slit profile. The slit profiles is modified to alter the velocity of the fluid stream through the slit. Three different slit profiles are considered viz., straight, converging and diverging slits. The combustion characteristics are evaluated in terms of the hydrogen combustion efficiency, combustion progress parameter and blow-off limits. The converging slit is found to exhibit better combustion efficiency compared to the other two slit profiles. The converging slit resulted in the formation of a secondary recirculation zone near the rear end of the bluff body. A novel approach towards understanding the flame splitting which finally results in blow-off is presented. Total viscosity is considered as the means to quantify the shear stress which is responsible for the flame stretching and eventual flame splitting. It is observed that the flame blows off at smaller inlet velocities in the combustor with the converging slit compared to the other slit profiles.
- 20 April 2021
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 40 (6) , e13658
Effect of exhaust gas recirculation on the performance and emission characteristics of a DI‐CI engine fueled with butanol/diesel blends
The rapid consumption of fossil fuels, ever rising energy demand, and rigorous emission norms have been attracting the attention of researchers toward clean renewable fuels such as alcohol‐based fuels. Higher chain alcohol fuels are attractive alternative fuels for use in diesel engine. A higher chain alcohol (butanol, pentanol, etc.,) has better blending properties, higher calorific value, and higher cetane number than the lower chain alcohol. Alcohol fuels can be produced from the biomass. Therefore, it is important to examine the fuel, as well as its blends with diesel fuel in diesel engine for the engine characteristics. The present paper aims at studying the performance characteristics of a DI‐CI engine using butanol/diesel (B/D) blends with and without exhaust gas recirculation (EGR). Experiments were performed on a single cylinder CI engine with two different B/D blends (20% and 40% by volume of butanol in the mixture—denoted as a Bu20 and Bu40), with different EGR rates (0%–30% in steps of 10%). The experimental results showed that the brake thermal efficiency (BTE) improved by 1.1% and 1.25% for Bu20 and Bu40 blends in comparison with Bu00. Nitrogen oxides (NOx) emissions reduced by 7.9%, 12.9% for Bu20 and Bu40 blends compared Bu00 respectively. Similarly, the soot emission decreased by 18% and 40.9% for Bu20 and Bu40 compared to Bu00. With the use of EGR, the NOx emissions significantly decreased. At 30% of EGR rate, the NOx emission reduced by 53.9%, 60.2%, and 67% for Bu00, Bu20, and Bu40, respectively. The soot emissions increased slightly at lower EGR rates of 0% to 20%. However, the soot emissions increased drastically at higher EGR rates for all the B/D blends. It is concluded that a combination of higher fraction of B/D blends along with a small EGR rate, can achieve lower emissions (soot and NOx) with a small penalty on the engine performance.
- 20 April 2021
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 40 (6) , e13658
Effect of exhaust gas recirculation on the performance and emission characteristics of a DI‐CI engine fueled with butanol/diesel blends
The rapid consumption of fossil fuels, ever rising energy demand, and rigorous emission norms have been attracting the attention of researchers toward clean renewable fuels such as alcohol‐based fuels. Higher chain alcohol fuels are attractive alternative fuels for use in diesel engine. A higher chain alcohol (butanol, pentanol, etc.,) has better blending properties, higher calorific value, and higher cetane number than the lower chain alcohol. Alcohol fuels can be produced from the biomass. Therefore, it is important to examine the fuel, as well as its blends with diesel fuel in diesel engine for the engine characteristics. The present paper aims at studying the performance characteristics of a DI‐CI engine using butanol/diesel (B/D) blends with and without exhaust gas recirculation (EGR). Experiments were performed on a single cylinder CI engine with two different B/D blends (20% and 40% by volume of butanol in the mixture—denoted as a Bu20 and Bu40), with different EGR rates (0%–30% in steps of 10%). The experimental results showed that the brake thermal efficiency (BTE) improved by 1.1% and 1.25% for Bu20 and Bu40 blends in comparison with Bu00. Nitrogen oxides (NOx) emissions reduced by 7.9%, 12.9% for Bu20 and Bu40 blends compared Bu00 respectively. Similarly, the soot emission decreased by 18% and 40.9% for Bu20 and Bu40 compared to Bu00. With the use of EGR, the NOx emissions significantly decreased. At 30% of EGR rate, the NOx emission reduced by 53.9%, 60.2%, and 67% for Bu00, Bu20, and Bu40, respectively. The soot emissions increased slightly at lower EGR rates of 0% to 20%. However, the soot emissions increased drastically at higher EGR rates for all the B/D blends. It is concluded that a combination of higher fraction of B/D blends along with a small EGR rate, can achieve lower emissions (soot and NOx) with a small penalty on the engine performance.
- 21 July 2020
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 40 (2)
Parametric optimization of direct injection CI engine to improve combustion characteristics
To achieve emission standard norms and higher fuel efficiency conversion are the main concerns in diesel engines. The single parametric study approach might not attain the optimal combustion characteristics. In order to overcome this issue, multi objective study has been carried out to achieve the higher performance and simultaneously reduction of emissions. The main objective of present article is identifying the optimum set of the engine parameters for diesel fuel, which gives better performance and emissions. Numerical analysis was carried out by using CONVERGE CFD software. Numerical analysis were carried out by varying the Compression Ratio (CR) (12–16.5), Start of Injection (SOI) (0–25° bTDC), Fuel Injection Pressure (FIP) (500–1,400), and Exhaust Gas Recirculation (EGR) (0–40%). Response surface methodology was used for optimization. The parameters are optimized for minimizing the NOx, soot, and ISFC by using the Response Surface Methodology (RSM). Regression equations were developed for the responses such as ISFC, NOx, and soot. It was observed that the interaction effects also play a major role in determining the performance and emission characteristics of the engine. The optimum combination of operating parameters was found to be CR 14.55, SOI 16.29° bTDC, FIP 855 bar, and EGR 26.15% with a composite desirability of 0.94. The corresponding NOx and soot emissions are reduced by 40.3% and 52.38%, respectively, and a marginal reduction in the ISFC is accomplished. Mixture homogeneity (TFDI) was improved 27% for optimum case compared to baseline configuration.
- 21 July 2020
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 40 (2)
Parametric optimization of direct injection CI engine to improve combustion characteristics
To achieve emission standard norms and higher fuel efficiency conversion are the main concerns in diesel engines. The single parametric study approach might not attain the optimal combustion characteristics. In order to overcome this issue, multi objective study has been carried out to achieve the higher performance and simultaneously reduction of emissions. The main objective of present article is identifying the optimum set of the engine parameters for diesel fuel, which gives better performance and emissions. Numerical analysis was carried out by using CONVERGE CFD software. Numerical analysis were carried out by varying the Compression Ratio (CR) (12–16.5), Start of Injection (SOI) (0–25° bTDC), Fuel Injection Pressure (FIP) (500–1,400), and Exhaust Gas Recirculation (EGR) (0–40%). Response surface methodology was used for optimization. The parameters are optimized for minimizing the NOx, soot, and ISFC by using the Response Surface Methodology (RSM). Regression equations were developed for the responses such as ISFC, NOx, and soot. It was observed that the interaction effects also play a major role in determining the performance and emission characteristics of the engine. The optimum combination of operating parameters was found to be CR 14.55, SOI 16.29° bTDC, FIP 855 bar, and EGR 26.15% with a composite desirability of 0.94. The corresponding NOx and soot emissions are reduced by 40.3% and 52.38%, respectively, and a marginal reduction in the ISFC is accomplished. Mixture homogeneity (TFDI) was improved 27% for optimum case compared to baseline configuration.
- 16 April 2020
- Published by Wiley in Asia-Pacific Journal of Chemical Engineering
- Vol. 15 (4)
Performance evaluation of an air breathing–direct methanol fuel cell with different cathode current collectors with liquid electrolyte layer
Development of possible technologies for the generation of green energy is the focus of research worldwide. Fuel cells are a promising option in this regard. Out of the various categories of fuel cells, air breathing–direct methanol fuel cells (AB‐DMFCs) are finding a prominent place as an electric power source for charging of compact electronic devices. In AB‐DMFC, the design and construction of the cathode current collector is very crucial, since the cathode current collector performs important functions in the fuel cell operation such as collecting the electrons, facilitating the flow of oxygen for the cathode reaction and evacuating the water bubbles formed at the cathode side. An ideal current collector improves the cell performance multifold. The present paper deals about the performance of an AB‐DMFC fitted with three different cathode current collector designs, viz., a wire mesh current collector (WMCC) made of SS316L, WMCC with a supporting plate (SP) and a perforated current collector (PCC) with an open ratio of 45.40%. A single serpentine flow channel engraved on a graphite plate was used as the anode flow channel plate. Experimental investigations are carried out to examine the impact of the cathode current collector design on the performance of AB‐DMFC and also by varying the operating parameters of methanol flow rate and concentration. The next stage of the experiments are carried out with the addition of a liquid electrolyte layer (LE), which is kept between two half Membrane Electrode Assemblies. Experimental results reveal that the LE layer enhances the fuel cell performance compared to conventional AB‐DMFC.
- 16 April 2020
- Published by Wiley in Asia-Pacific Journal of Chemical Engineering
- Vol. 15 (4)
Performance evaluation of an air breathing–direct methanol fuel cell with different cathode current collectors with liquid electrolyte layer
Development of possible technologies for the generation of green energy is the focus of research worldwide. Fuel cells are a promising option in this regard. Out of the various categories of fuel cells, air breathing–direct methanol fuel cells (AB‐DMFCs) are finding a prominent place as an electric power source for charging of compact electronic devices. In AB‐DMFC, the design and construction of the cathode current collector is very crucial, since the cathode current collector performs important functions in the fuel cell operation such as collecting the electrons, facilitating the flow of oxygen for the cathode reaction and evacuating the water bubbles formed at the cathode side. An ideal current collector improves the cell performance multifold. The present paper deals about the performance of an AB‐DMFC fitted with three different cathode current collector designs, viz., a wire mesh current collector (WMCC) made of SS316L, WMCC with a supporting plate (SP) and a perforated current collector (PCC) with an open ratio of 45.40%. A single serpentine flow channel engraved on a graphite plate was used as the anode flow channel plate. Experimental investigations are carried out to examine the impact of the cathode current collector design on the performance of AB‐DMFC and also by varying the operating parameters of methanol flow rate and concentration. The next stage of the experiments are carried out with the addition of a liquid electrolyte layer (LE), which is kept between two half Membrane Electrode Assemblies. Experimental results reveal that the LE layer enhances the fuel cell performance compared to conventional AB‐DMFC.
- 1 March 2020
- Published by Elsevier in Chinese Journal of Chemical Engineering
- Vol. 28 (3) , 824-831
Influence of bio-inspired flow channel designs on the performance of a PEM fuel cell
- 1 March 2020
- Published by Elsevier in Chinese Journal of Chemical Engineering
- Vol. 28 (3) , 824-831
Influence of bio-inspired flow channel designs on the performance of a PEM fuel cell
- Open Access
- 1 February 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1473 (1)
Steam condensation by heat pipes
The present paper describes the usage of heat pipes for phase transformation of steam that is steam condensation. The application of heat pipes were reviewed and it is found that heat pipes were never explored for steam condensation since its inception. Hence, a heat pipe had been designed for condensation purpose and the features of this designed heat pipe like, material of construction, length, and diameter were presented. The thermodynamic limits of the designed heat pipe were calculated theoretically. Practical results of experiments were also presented.
- 1 February 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1473 (1)
Open AccessSteam condensation by heat pipes
The present paper describes the usage of heat pipes for phase transformation of steam that is steam condensation. The application of heat pipes were reviewed and it is found that heat pipes were never explored for steam condensation since its inception. Hence, a heat pipe had been designed for condensation purpose and the features of this designed heat pipe like, material of construction, length, and diameter were presented. The thermodynamic limits of the designed heat pipe were calculated theoretically. Practical results of experiments were also presented.