FLFeng Li

Feng Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Feng Li has a total of 35 co-authors. Here are the top co-authors by number of shared publications:

  • Da Li

    College of Architecture and Civil Engineering, Yancheng Polytechnic College Yancheng China

    3 shared publications
  • Dongdong Zhang

    College of Field Engineering, Army Engineering University of PLA , Nanjing 210007 , China

    3 shared publications
  • Chenglin Liu

    Army Engineering University of PLA

    2 shared publications
  • Hengming Zhang

    College of Field Engineering, Army Engineering University of PLA, Nanjing, China

    2 shared publications
  • Jie Tao

    Institute of Field Engineering, Peoples Liberation Army University of Science and Technology, PLA Univ. of Sci. & Tech., Nanjing, China

    2 shared publications
  • Qilin Zhao

    School of Mechanical and Power Engineering of Nanjing Univ. of Tech, Nanjing, China

    2 shared publications

Latest Publications

  • Load-bearing performance of curved-pultruded GFRP square tube-metal hybrid emergency bridge: Experimental and numerical investigations

    by Zecheng Tong, Chenglin Liu, Feng Li, Jia Chen

    Extreme events often disrupt transportation networks and create an urgent need for lightweight, rapidly deployable emergency bridges. To overcome the high self-weight, corrosion susceptibility, and limited deployment efficiency of conventional steel systems, and to resolve the stiffness-assembly efficiency trade-off in existing fiber-reinforced polymer (FRP) emergency bridges, this study proposes and experimentally evaluates a curved-pultruded glass fiber-reinforced polymer (GFRP) square-tube-metal hybrid emergency bridge. In the proposed system, arch-shaped curved-pultruded GFRP square tubes enhance structural stiffness through geometric arch action, whereas modular joints using pre-tightened tooth connections (PTTCs) and single-lug-and-yoke-plate (SLYP) joints enable rapid assembly. Three-point bending tests were performed under four representative SLYP pin configurations within the elastic stage, followed by an ultimate failure test on the symmetric 3-pin configuration, with pins installed in Girders 1, 3, and 5. The results demonstrate that pin configuration governs the global stiffness and transverse load-sharing behavior of the bridge. Specifically, increasing the number of pins improves stiffness by enhancing tensile-force transfer and rotational restraint between adjacent girders, whereas a more uniform pin layout promotes better transverse force coordination. Ultimate failure was governed by local buckling and matrix compression damage near the GFRP arch-foot region, with no evident damage in the PTTCs or bolt-hole areas. A validated finite element (FE) model agreed well with the experimental results in terms of ultimate bearing capacity, and parametric analyses further confirmed that uniform pin arrangements delay the onset of local buckling and improve global structural stability. The proposed system therefore offers a promising solution for short-span composite emergency bridges.

  • Prediction and Model Validation of Corrosion Fatigue Life for BFRP Tendons Under Combined Acidic Environment and Temperature

    by Xia Liu, Hangyu Zhou, Xin Wang, Jingyang Zhou, Jiazhan Xie, Feng Li, Zhishen Wu

    The widespread application of fiber‐reinforced polymers (FRP) in engineering is primarily attributed to their superior durability compared to traditional materials. However, under prolonged exposure to harsh service environments, the material inevitably undergoes progressive degradation. The existing durability studies and life prediction models have largely overlooked the synergistic effects of combined environmental actions and mechanical loading conditions. To address this gap, this paper investigates the corrosion fatigue behavior of BFRP tendons under combined cyclic loading, acidic environments (pH = 1.5, 2.5, and 7.0), and temperatures (25°C–50°C). An experimental matrix was designed to couple these variables, enabling the identification of fatigue failure modes and the development of S – N models for each environmental condition. A sequential multifactor life prediction model was developed and validated through a case study. Results reveal that ignoring the combined effect of temperature and acidity leads to an 83.0% overestimation of service life, underscoring the necessity of considering multifactor synergy for realistic durability design.

  • Effect of Adhesive Filling on Tensile Performance of Hybrid Tooth‐Bolt Connections for Pultruded FRP Profiles

    by Shasha Liang, Ruijie Zhu, Feng Li, Zecheng Tong, Da Li

    Efficient load transfer remains a key challenge in hybrid tooth–bolt connections for fiber‐reinforced polymer (FRP) profiles. Here we propose a simple strengthening strategy based on adhesive filling of the bolt–hole clearance with a high‐performance epoxy resin. We tested joints with different tooth lengths, tooth depths and bolt preloads, both with and without adhesive filling. Adhesive filling markedly increased the ultimate load and pre‐peak energy absorption, while preserving the shear‐dominated final failure mode. It nevertheless changed the damage sequence. In joints without adhesive filling, the teeth carried most of the early‐stage load. Failure occurred abruptly when tooth‐root interlaminar shear triggered in‐plane shear damage around the outer bolt hole. With adhesive filling, the resin formed a continuous shear‐transfer path between the bolt and the hole wall. This promoted early bolt engagement, improved load redistribution and produced a more progressive response, including direct shear and crack‐then‐shear failure. Finite‐element simulations using zero‐thickness cohesive elements and the Hashin criterion captured the measured load–displacement responses and observed failure modes, thereby clarifying the strengthening mechanism. These findings show that adhesive filling provides a simple and effective route to improving the capacity and reliability of hybrid tooth–bolt connections for FRP profiles.


  • Open Access

    Evaluation of flexural deformation of a lightweight fabricated GFRP emergency bridge with a novel broken-line prestressed cable system

    by Chenglin Liu, Feng Li, Ruijie Zhu, Ming Ni

    To address the urgent need for rapid traffic restoration after bridge collapse, a novel lightweight fabricated GFRP (Glass Fiber-Reinforced Polymer) emergency bridge with a broken-line prestressed cable system was developed. Full-scale four-point bending tests and initial deformation measurement tests caused by dead load and clearance effect were conducted to determine the flexural deformation of the bridge. It was demonstrated that the broken-line prestressed cable system substantially enhances the structural stiffness while maintaining the advantages of modular assembly. The experimental results revealed that SLYP (Single Lug and Yoke Plate) joints serve as critical load transfer components, and the deformation caused by the clearance effect of SLYP joints cannot be ignored. The calculation method for the equivalent flexural stiffness, distinguishing GTAL (GFRP tube and aluminum alloy deck) part and SLYP joint part, was given. The flexural deformation caused by dead load, live load, prestressing, and clearance effect, considering the axial deformation and spatial angle reduction effect of the steel wire cables, was proposed based on the flexibility method. The validated analytical model exhibited excellent agreement with experimental data. The main parameters influencing the flexural deformation, such as the equivalent flexural stiffness, clearance between the pin and pinhole, height of the segment, length of the vertical stay and turning component, and SLYP joint arrangement, were discussed in detail based on the proposed method.


  • Buckling critical load prediction of pultruded fiber-reinforced polymer columns and feature analysis by machine learning

    by Hengming Zhang, Da Li, Feng Li

    For slender FRP columns, predicting the global buckling critical loads is crucial in structural design. However, there is a lack of a consensus prediction method based on specialized domain knowledge. To address this issue, this study created a comprehensive database by collecting 365 experimental data related to global buckling of axially loaded pultruded FRP columns to predict buckling critical loads using such machine learning methods as extreme gradient boosting, artificial neural network, and support vector regression. The prediction accuracy and stability of the machine learning prediction methods were evaluated, and the interpretability of the features was analyzed in depth. The results show that the prediction accuracy of the traditional theoretical methods is low, while that of the machine learning methods is high. The contribution of geometric parameters to the buckling critical load is more than 80%. The contribution of material parameters to the buckling critical load is small, less than 20%. The cross-sectional moment of inertia has the most significant effect on the buckling critical load, while the shear modulus and compressive strength have a smaller effect.


  • Local bearing behavior of a novel adhesively bonded aluminum SHST bridge deck

    by Chenglin Liu, Feng Li, Yinzhi Zhou, Xulong Hao, Yan Chen, Jiancheng Gong, Yan Li


  • Fatigue damage propagation of FRP under coupling effect of cyclic load and corrosion

    by Liu Xia, Li Feng, Wang Xin, Zhou Jingyang, Liang Mengdie, Zhang Leizhi, Huang Huang, Wu Zhishen

    Interlaminar fracture or delamination is one of the major failure modes for fiber reinforced polymer (FRP) laminate. Especially, the synergistic effect of environmental exposure and fatigue loads accelerates interface degradation. The main objective in this work was to investigate the fatigue damage propagation of basalt FRP (BFRP) laminate under coupling of acidic environment and fatigue load. The fatigue cycling of 40,000 and the maximum stress of 30% f u ( f u = ultimate tensile strength) were adopted. The fatigue specimens under air condition (air fatigue), immersing in water (water fatigue) and immersing in acid (acid fatigue) were introduced. The double cantilever beam (DCB) test was used to evaluate the interlaminar damage of BFRP laminate after fatigue cycling. The fatigue damage propagation mechanism was explored by means of failure modes, load displacement curves, mode I fracture toughness and crack propagation resistance model. The results show that the fatigue weakened the interlaminar properties and resulted in reduced fiber bridging. Especially for the acid fatigue, the laminate was damaged by the coupling of fatigue and acid corrosion. The linear loading stage, nonlinear slow growing stage, stable crack propagation stage and linear unloading stage for DCB after fatigue were observed in the load–displacement curve. The fatigue cycling has caused fracture toughness decrease of 15.0%, 13.8% and 24.1% on air fatigue, water fatigue and acid fatigue respectively. Compared to air fatigue, additional 9.1% interlaminar toughness decrease was evidenced for acidic corrosion fatigue due to the coupling effect of chemical corrosion and physical swelling. The fluctuating decline of crack resistance was caused by discontinuous interface damage, and the interlayer damage was randomly distributed. Thus the interface damage model was proposed to characterize the damage distribution and the damage size. Highlights: Degradation law of BFRP under the coupling effect of acid immersion and fatigue load. Interface damage model for characterization of the damage distribution and damage size. Fatigue damage propagation of BFRP under coupling effect of cyclic load and corrosion.


  • Experimental investigation on the axial compression behaviour of perforated glass fibre reinforced plastic medium-length tubes

    by Da Li, Feng Li

    This paper aims to investigate the axial compression behaviour of perforated glass fibre reinforced plastic (GFRP) circular tubes. A total of 12 GFRP medium-length tubes with and without circular holes were tested under axial compression. The influence of hole size and hole quantity on the failure mode and mechanical behaviour of perforated GFRP tubes were carefully evaluated. The overall buckling failure and material strength failure, mainly determined by the hole size, were observed in the axial compression tests. The critical load and axial stiffness of the perforated tubes decreased further with the increase of hole sizes and quantities, compared to those of the intact GFRP tubes. To reveal the damage mechanism of perforated GFRP tubes, three-dimensional digital image correlation (3D-DIC) technique was used to analyse the evolution of full-field strain around the hole. It was demonstrated that the damage mechanisms of the overall buckling failure and material strength failure were respectively compression-shear destruction and tension-shear destruction in the high strain concentration regions around the hole. Finally, design-oriented equations were proposed to predict the critical load and axial stiffness of perforated GFRP tubes under axial compression, and 95% confidence interval was used for interval estimation. The proposed equations were in good agreement with the test results. In addition, the prediction results of axial stiffness are generally more accurate than that of critical load.