Echezona Nnaemeka Obika
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Echezona Nnaemeka Obika has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Florian Heberle
Chair of Engineering Thermodynamics and Transport Processes (LTTT), Center of Energy Technology (ZET), University of Bayreuth, 95440 Bayreuth, Germany
3 shared publications Dieter Brüggemann
2 shared publications- Obiora Nnaemeka Ezenwa
Department of Mechanical Engineering, Nnamdi Azikiwe University, Awka, Nigeria
2 shared publications Benjamin Segun Oluwadare
Department of Mechanical Engineering, Ekiti State University PMB 5363, Ado Ekiti, Ekiti State, Nigeria
1 shared publication- Chinedu Josiah Umembamalu
Department of Chemical Engineering, Nnamdi Azikiwe University, P.M.B. 5025, Awka, 420218, Nigeria
1 shared publication Chinweze Arinze Everest
Department of Mechanical Engineering, Nnamdi Azikiwe University, Awka, Nigeria
1 shared publication
Latest Publications
- Open Access
- 6 June 2026
- Published by Elsevier in Applied Thermal Engineering
- Vol. 302
Experimental optimisation of the performance of a high-temperature heat pump under part load conditions
- 6 June 2026
- Published by Elsevier in Applied Thermal Engineering
- Vol. 302
Open AccessExperimental optimisation of the performance of a high-temperature heat pump under part load conditions
- Open Access
- 18 July 2025
- Published by Elsevier in Energy Conversion and Management: X
- Vol. 27
From organic rankine cycles to high-temperature heat pumps: A thermo-economic investigation of potential working fluids
- 18 July 2025
- Published by Elsevier in Energy Conversion and Management: X
- Vol. 27
Open AccessFrom organic rankine cycles to high-temperature heat pumps: A thermo-economic investigation of potential working fluids
- 19 July 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 237 (4) , 1168-1178
Thermophysical properties and grain size effects in Luffa Cylindrica-modified clay composites for thermal insulation
The study explored the thermal insulation potential of composite material made from clay and Luffa cylindrica. Clay/ Luff cylindrica composite (denoted as Clay/L-C) was developed from natural resources. In the research, Luffa cylindrica particles of different grain sizes and different proportions were mixed with clay, and thermal evaluations were done with respect to thermal conductivity, thermal diffusivity, specific heat capacity, mass depletion with temperature, and microstructure. Two different mixture ratios, namely 4:1and 3:2 corresponding to 20 wt % and 40 wt % Luffa cylindrica particle, respectively, were used for Clay/ Luffa cylindrica combination. While Luffa cylindrica particle sizes varied from 600µm to 300µm and 150µm, the effects of Luffa cylindrica content and particle size on thermal properties were then examined. These novel composite materials developed in this study demonstrate motivating potential for enhanced thermal insulation when compared to unmodified clay. Improved thermal insulation performance indicated by thermal properties was observed for all the modified samples. This is on the account of reduced thermal conductivity of the modified samples. The best sample possessed thermal conductivity, thermal resistivity, thermal diffusivity, specific heat capacity, and porosity values of 0.216 W/mK, 462.90°C.cm/W, 0.123 mm/s2 1.493 MJ/m3K, and 89.3%, respectively. Results show that Luffa cylindrica fiber can be applied as an additive for effective thermal insulation. Development in this area of study is very necessary especially as the raw materials are readily available and cost-effective.
- 19 July 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 237 (4) , 1168-1178
Thermophysical properties and grain size effects in Luffa Cylindrica-modified clay composites for thermal insulation
The study explored the thermal insulation potential of composite material made from clay and Luffa cylindrica. Clay/ Luff cylindrica composite (denoted as Clay/L-C) was developed from natural resources. In the research, Luffa cylindrica particles of different grain sizes and different proportions were mixed with clay, and thermal evaluations were done with respect to thermal conductivity, thermal diffusivity, specific heat capacity, mass depletion with temperature, and microstructure. Two different mixture ratios, namely 4:1and 3:2 corresponding to 20 wt % and 40 wt % Luffa cylindrica particle, respectively, were used for Clay/ Luffa cylindrica combination. While Luffa cylindrica particle sizes varied from 600µm to 300µm and 150µm, the effects of Luffa cylindrica content and particle size on thermal properties were then examined. These novel composite materials developed in this study demonstrate motivating potential for enhanced thermal insulation when compared to unmodified clay. Improved thermal insulation performance indicated by thermal properties was observed for all the modified samples. This is on the account of reduced thermal conductivity of the modified samples. The best sample possessed thermal conductivity, thermal resistivity, thermal diffusivity, specific heat capacity, and porosity values of 0.216 W/mK, 462.90°C.cm/W, 0.123 mm/s2 1.493 MJ/m3K, and 89.3%, respectively. Results show that Luffa cylindrica fiber can be applied as an additive for effective thermal insulation. Development in this area of study is very necessary especially as the raw materials are readily available and cost-effective.
- Open Access
- 28 June 2022
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 14 (6)
The effect of flux composition on tensile strength of re-engineered E308H-16 electrode
A stainless steel flux for manual metal arc welding (MMAW) has been developed. The coated electrode is a rutile electrode whose basic components are titanium (IV) oxide and stainless steel powder. Some of the other components were substituted; the more popular but expensive potassium silicate binder was replaced with readily available sodium silicate binder. For the binder to perform effectively, it was enriched with potassium carbonate, which was sourced locally from palm bunch. Cellulose, a good gas former was replaced with starch, which was gotten from cassava. The components were sieved into 75 µm particle size. The experimental design was set up using Central Composite Design in Design Expert software. The design varied the percentage composition of calcium carbonate, binder, titanium (IV) oxide, silicon (IV) oxide, and stainless steel powder. Twenty-six (26) test samples were produced using the central composite design tool of the design expert software and tested for tensile strength. The experimental results were analyzed and optimized using Response Surface Methodology and Validated using the ANOVA tool of the Design Expert software. An optimal composition of 10% CaCO3, 13% Binder, 13% Titanium oxide, 12% silicon (IV) oxide, and 36% stainless steel powder were obtained to give a corresponding 539.7 N/mm2 tensile strength.
- 28 June 2022
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 14 (6)
Open AccessThe effect of flux composition on tensile strength of re-engineered E308H-16 electrode
A stainless steel flux for manual metal arc welding (MMAW) has been developed. The coated electrode is a rutile electrode whose basic components are titanium (IV) oxide and stainless steel powder. Some of the other components were substituted; the more popular but expensive potassium silicate binder was replaced with readily available sodium silicate binder. For the binder to perform effectively, it was enriched with potassium carbonate, which was sourced locally from palm bunch. Cellulose, a good gas former was replaced with starch, which was gotten from cassava. The components were sieved into 75 µm particle size. The experimental design was set up using Central Composite Design in Design Expert software. The design varied the percentage composition of calcium carbonate, binder, titanium (IV) oxide, silicon (IV) oxide, and stainless steel powder. Twenty-six (26) test samples were produced using the central composite design tool of the design expert software and tested for tensile strength. The experimental results were analyzed and optimized using Response Surface Methodology and Validated using the ANOVA tool of the Design Expert software. An optimal composition of 10% CaCO3, 13% Binder, 13% Titanium oxide, 12% silicon (IV) oxide, and 36% stainless steel powder were obtained to give a corresponding 539.7 N/mm2 tensile strength.
- Open Access
- 23 February 2021
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 13 (2)
Effect of filler carbonization on agro-waste based ceiling board
This work presents the use as a filler of carbonized breadfruit seed coat and recycled low density polyethylene as the binder in ceiling board manufacturing. The depulped bread fruit seed was carbonized for 2 h at a temperature of 500°C. The experimental design was set up using the Design Expert software. A total of 30 experimental tests were developed for four parameters and three responses. The parameters are carbonized bread fruit seed coat/recycled Low Density Polyethylene mass ratio (filler-binder mass ratio), compaction time, compaction temperature and compaction pressure while the responses are thermal conductivity, thickness swell and water absorption. The models developed have been validated using the Study of Variance (ANOVA). Using the 3D surface map, the influence of the parameters on the responses was studied. The optimization method of the Design Expert program was used to evaluate the optimal level of the parameters that will produce the best possible result from their combination. The result gave optimal values of 16.206% filler/rLDPE, 9.406minutes compaction time, 200°C compaction temperature and 11 MPa compaction pressure, which gave 0.246% Water Absorption, 1.998% Thickness Swell and 2.898 W/M.K Thermal Conductivity.
- 23 February 2021
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 13 (2)
Open AccessEffect of filler carbonization on agro-waste based ceiling board
This work presents the use as a filler of carbonized breadfruit seed coat and recycled low density polyethylene as the binder in ceiling board manufacturing. The depulped bread fruit seed was carbonized for 2 h at a temperature of 500°C. The experimental design was set up using the Design Expert software. A total of 30 experimental tests were developed for four parameters and three responses. The parameters are carbonized bread fruit seed coat/recycled Low Density Polyethylene mass ratio (filler-binder mass ratio), compaction time, compaction temperature and compaction pressure while the responses are thermal conductivity, thickness swell and water absorption. The models developed have been validated using the Study of Variance (ANOVA). Using the 3D surface map, the influence of the parameters on the responses was studied. The optimization method of the Design Expert program was used to evaluate the optimal level of the parameters that will produce the best possible result from their combination. The result gave optimal values of 16.206% filler/rLDPE, 9.406minutes compaction time, 200°C compaction temperature and 11 MPa compaction pressure, which gave 0.246% Water Absorption, 1.998% Thickness Swell and 2.898 W/M.K Thermal Conductivity.
- Open Access
Development of ceiling board using breadfruit seed coat and recycled low density polyethylene