Obiora Nnaemeka Ezenwa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Obiora Nnaemeka Ezenwa has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Echezona Nnaemeka Obika
Department of Mechanical Engineering, Nnamdi Azikiwe University, Awka, Nigeria
2 shared publications Anthony Amaechi Okafor
Nnamdi Azikiwe University, Awka
1 shared publicationArinze Everest Chinweze
Nnamdi Azikiwe University, Awka
1 shared publication- Arinze Everest Chinweze
Department of Mechanical Engineering, Nnamdi Azikiwe University, Awka, Nigeria
1 shared publication - Augustine Uzodinma Madumere
Department of Mechanical Engineering, Nnamdi Azikiwe University, Awka, Nigeria
1 shared publication Calistus Princewill Odeh
Nnamdi Azikiwe University, Awka
1 shared publication
Latest Publications
- Open Access
- 29 August 2025
- Published by Conscientia Beam in International Journal of Sustainable Energy and Environmental Research
- Vol. 14 (2) , 120-132
Development and performance assessment of post-combustion emission control device, embedded with breadfruit pulp biochar
This study presents the design, fabrication, and experimental evaluation of a small-scale carbon capture device aimed at mitigating exhaust emissions from petrol generators. Motivated by Nigeria’s heavy dependence on fossil fuels and the associated greenhouse gas (GHG) emissions, the research explores the use of breadfruit pulp–derived biochar as a low-cost, sustainable adsorbent for post-combustion carbon dioxide (CO2) capture. The carbon capture system was developed using stainless-steel chambers arranged in series, each packed with graded biochar particles to enhance gas–adsorbent contact. Theoretical design analyses and SolidWorks static simulations were performed to verify the structural adequacy under combined thermal (600 °C) and pressure (7 kPa) loads. Experimental results using an air quality detector showed significant reductions in CO and CO2 emissions, demonstrating the biochar’s adsorption efficiency. Simulation outcomes indicated minimal deformation and confirmed the mechanical stability of the capture unit, although localized stress concentrations suggested a need for minor design improvements. Overall, the study validates the feasibility of using agricultural waste–derived carbon materials for emission control, offering a sustainable solution for small-scale power sources in developing regions.
- 29 August 2025
- Published by Conscientia Beam in International Journal of Sustainable Energy and Environmental Research
- Vol. 14 (2) , 120-132
Open AccessDevelopment and performance assessment of post-combustion emission control device, embedded with breadfruit pulp biochar
This study presents the design, fabrication, and experimental evaluation of a small-scale carbon capture device aimed at mitigating exhaust emissions from petrol generators. Motivated by Nigeria’s heavy dependence on fossil fuels and the associated greenhouse gas (GHG) emissions, the research explores the use of breadfruit pulp–derived biochar as a low-cost, sustainable adsorbent for post-combustion carbon dioxide (CO2) capture. The carbon capture system was developed using stainless-steel chambers arranged in series, each packed with graded biochar particles to enhance gas–adsorbent contact. Theoretical design analyses and SolidWorks static simulations were performed to verify the structural adequacy under combined thermal (600 °C) and pressure (7 kPa) loads. Experimental results using an air quality detector showed significant reductions in CO and CO2 emissions, demonstrating the biochar’s adsorption efficiency. Simulation outcomes indicated minimal deformation and confirmed the mechanical stability of the capture unit, although localized stress concentrations suggested a need for minor design improvements. Overall, the study validates the feasibility of using agricultural waste–derived carbon materials for emission control, offering a sustainable solution for small-scale power sources in developing regions.
- Open Access
- 6 January 2024
- Published by Science Publishing Corporation in International Journal of Engineering & Technology
- Vol. 13 (1) , 87-94
Spectrophotometric analysis of surface free energies of polymer surfaces
This work is focused on the use of a spectrophotometer to determine the surface free energies of polymers. To study the molecular system interaction, there is a need for a simpler method to calculate free energy. The free energy determines the phase interaction of polymer film at different concentrations. One of the simpler methods is the use of a spectrophotometer. The methodology involved taking four polymer samples and dissolving each into different concentrations for absorbance measurement using an ultraviolet spectrophotometer. From the absorbance data, various variables (e.g., dielectric constant, etc.) were derived. This variable (dielectric constant) was also used to determine the haymaker constant of each concentration of each polymer. The surface free energies are determined from the values of the Hamaker constant. The peak values of surface free energies for Polyvinyl alcohol (PVA), Polyethylene glycol (PEG) and Polyacrylamide (PAM) were also obtained from spectrophotometer results and found to be the same, 57.51mJ/m^2. Contact angle measurements on concentration were also obtained. It was found that the contact angle measured on PVA and PEG at different concentrations tends to decrease with an increase in concentration. The results, therefore, show that PVA and PEG surfaces tend to be hydrophilic as concentration increases while PAM and Polyvinyl acetate (PVAC indicate hydrophobic. Surface free energies obtained from the spectrophotometric result and contact angle show little significant difference of about 6.9% and they followed the trend when related with other surface properties.
- 6 January 2024
- Published by Science Publishing Corporation in International Journal of Engineering & Technology
- Vol. 13 (1) , 87-94
Open AccessSpectrophotometric analysis of surface free energies of polymer surfaces
This work is focused on the use of a spectrophotometer to determine the surface free energies of polymers. To study the molecular system interaction, there is a need for a simpler method to calculate free energy. The free energy determines the phase interaction of polymer film at different concentrations. One of the simpler methods is the use of a spectrophotometer. The methodology involved taking four polymer samples and dissolving each into different concentrations for absorbance measurement using an ultraviolet spectrophotometer. From the absorbance data, various variables (e.g., dielectric constant, etc.) were derived. This variable (dielectric constant) was also used to determine the haymaker constant of each concentration of each polymer. The surface free energies are determined from the values of the Hamaker constant. The peak values of surface free energies for Polyvinyl alcohol (PVA), Polyethylene glycol (PEG) and Polyacrylamide (PAM) were also obtained from spectrophotometer results and found to be the same, 57.51mJ/m^2. Contact angle measurements on concentration were also obtained. It was found that the contact angle measured on PVA and PEG at different concentrations tends to decrease with an increase in concentration. The results, therefore, show that PVA and PEG surfaces tend to be hydrophilic as concentration increases while PAM and Polyvinyl acetate (PVAC indicate hydrophobic. Surface free energies obtained from the spectrophotometric result and contact angle show little significant difference of about 6.9% and they followed the trend when related with other surface properties.
- Open Access
- 4 January 2023
- Published by Springer Nature in Research Square
Thermal Behaviour of Agro-waste Based Ceiling Board and Its Filler Material
The thermal behavior of a ceiling board produced with breadfruit seed coat as the filler material, and recycled Low Density Polyethylene, as the binder, was investigated. The Breadfruit seed coat was treated with sodium hydroxide and acetic acid, to remove the pigments. The ceiling material was produced with 19.722% filer-binder ratio, and pressed for 10 minutes, at temperature and pressure of 197.31 oC and 9.042 MPa respectively. Lee-Charton’s apparatus was used to determine the thermal conductivity of the produced material, which gave a value of 0.362 Wm− 1K− 1 and the corresponding thermal diffusivity and resistivity of 5.24 x 10− 7 m2/s, and 2.76 Wm− 1K− 1, respectively. Thermo-gravimetric analyzer and Digital Scanning Calorimeter was used to study the thermal behavior the filler material and the produced sample, which showed a good thermal stability. Hence, this research showed that the produced material is suitable for ceiling board application.
- 4 January 2023
- Published by Springer Nature in Research Square
Open AccessThermal Behaviour of Agro-waste Based Ceiling Board and Its Filler Material
The thermal behavior of a ceiling board produced with breadfruit seed coat as the filler material, and recycled Low Density Polyethylene, as the binder, was investigated. The Breadfruit seed coat was treated with sodium hydroxide and acetic acid, to remove the pigments. The ceiling material was produced with 19.722% filer-binder ratio, and pressed for 10 minutes, at temperature and pressure of 197.31 oC and 9.042 MPa respectively. Lee-Charton’s apparatus was used to determine the thermal conductivity of the produced material, which gave a value of 0.362 Wm− 1K− 1 and the corresponding thermal diffusivity and resistivity of 5.24 x 10− 7 m2/s, and 2.76 Wm− 1K− 1, respectively. Thermo-gravimetric analyzer and Digital Scanning Calorimeter was used to study the thermal behavior the filler material and the produced sample, which showed a good thermal stability. Hence, this research showed that the produced material is suitable for ceiling board application.
- Open Access
- 23 February 2021
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 13 (2)
Effect of filler carbonization on agro-waste based ceiling board
This work presents the use as a filler of carbonized breadfruit seed coat and recycled low density polyethylene as the binder in ceiling board manufacturing. The depulped bread fruit seed was carbonized for 2 h at a temperature of 500°C. The experimental design was set up using the Design Expert software. A total of 30 experimental tests were developed for four parameters and three responses. The parameters are carbonized bread fruit seed coat/recycled Low Density Polyethylene mass ratio (filler-binder mass ratio), compaction time, compaction temperature and compaction pressure while the responses are thermal conductivity, thickness swell and water absorption. The models developed have been validated using the Study of Variance (ANOVA). Using the 3D surface map, the influence of the parameters on the responses was studied. The optimization method of the Design Expert program was used to evaluate the optimal level of the parameters that will produce the best possible result from their combination. The result gave optimal values of 16.206% filler/rLDPE, 9.406minutes compaction time, 200°C compaction temperature and 11 MPa compaction pressure, which gave 0.246% Water Absorption, 1.998% Thickness Swell and 2.898 W/M.K Thermal Conductivity.
- 23 February 2021
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 13 (2)
Open AccessEffect of filler carbonization on agro-waste based ceiling board
This work presents the use as a filler of carbonized breadfruit seed coat and recycled low density polyethylene as the binder in ceiling board manufacturing. The depulped bread fruit seed was carbonized for 2 h at a temperature of 500°C. The experimental design was set up using the Design Expert software. A total of 30 experimental tests were developed for four parameters and three responses. The parameters are carbonized bread fruit seed coat/recycled Low Density Polyethylene mass ratio (filler-binder mass ratio), compaction time, compaction temperature and compaction pressure while the responses are thermal conductivity, thickness swell and water absorption. The models developed have been validated using the Study of Variance (ANOVA). Using the 3D surface map, the influence of the parameters on the responses was studied. The optimization method of the Design Expert program was used to evaluate the optimal level of the parameters that will produce the best possible result from their combination. The result gave optimal values of 16.206% filler/rLDPE, 9.406minutes compaction time, 200°C compaction temperature and 11 MPa compaction pressure, which gave 0.246% Water Absorption, 1.998% Thickness Swell and 2.898 W/M.K Thermal Conductivity.
- Open Access
Development of ceiling board using breadfruit seed coat and recycled low density polyethylene