Yongqiang Pan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yongqiang Pan has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Huan Liu
Key Laboratory of the Ministry of Education & Thin Film and Optical Manufacturing Technology, School of Opto-Electronic Engineering, Xi’an Technological University, Xi’an, Shaanxi 710021, China
3 shared publications - Jijie Zhao
Key Laboratory of Sensor and Sensor Technology, Institute of Sensor Technology, Gansu Academy of Sciences, Lanzhou, China
3 shared publications - Shengyong Wang
Key Laboratory of the Ministry of Education & Thin Film and Optical Manufacturing Technology, School of Opto-Electronic Engineering, Xi’an Technological University, Xi’an, Shaanxi 710021, China
3 shared publications - Dong Li
School of Optoelectronic Engineering, Xi’an Technological University, Xi’an 710021, China
2 shared publications - Fei Gao
School of Optoelectronic Engineering, Xi’an Technological University, Xi’an 710021, China
2 shared publications - Shuai Wen
Key Laboratory of the Ministry of Education & Thin Film and Optical Manufacturing Technology, School of Opto-Electronic Engineering, Xi’an Technological University, Xi’an, Shaanxi 710021, China
2 shared publications
Latest Publications
- 19 November 2024
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 26 (47) , 29532-29540
A two-step junction welding technique for achieving high-performance broadband silver nanowire transparent conductive films
Transparent conductive films (TCFs) are critical components of various optoelectronic and photovoltaic devices. The performance of TCFs is mainly ascribed to their superior transparency and low sheet resistance. However, the welding strategy for silver nanowires (AgNWs), the primary material used in TCFs, can significantly affect the optical and electrical properties of the films. Herein, we report a simple and effective method for preparing AgNWs TCFs with superior broadband transparency and conductivity. By applying pressure to the surface of graphene, we successfully enhanced the tight connections between loose nanowires. Based on this, we developed a high-performance, wide-spectrum TCF and employed ultraviolet welding as its post-treatment method. The sheet resistance of the electrode decreased to 27.1 Ω sq−1 with the addition of graphene films, and subsequent UV light welding further reduced the resistance value by 25.1%. Moreover, the incorporation of graphene films provides excellent protection for AgNWs against oxidation. One month later, compared to AgNWs without a protective coating, the increase in sheet resistance was reduced by 414.6%. This study provides a new method for preparing TCFs with wide spectrum and high performance.
- 19 November 2024
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 26 (47) , 29532-29540
A two-step junction welding technique for achieving high-performance broadband silver nanowire transparent conductive films
Transparent conductive films (TCFs) are critical components of various optoelectronic and photovoltaic devices. The performance of TCFs is mainly ascribed to their superior transparency and low sheet resistance. However, the welding strategy for silver nanowires (AgNWs), the primary material used in TCFs, can significantly affect the optical and electrical properties of the films. Herein, we report a simple and effective method for preparing AgNWs TCFs with superior broadband transparency and conductivity. By applying pressure to the surface of graphene, we successfully enhanced the tight connections between loose nanowires. Based on this, we developed a high-performance, wide-spectrum TCF and employed ultraviolet welding as its post-treatment method. The sheet resistance of the electrode decreased to 27.1 Ω sq−1 with the addition of graphene films, and subsequent UV light welding further reduced the resistance value by 25.1%. Moreover, the incorporation of graphene films provides excellent protection for AgNWs against oxidation. One month later, compared to AgNWs without a protective coating, the increase in sheet resistance was reduced by 414.6%. This study provides a new method for preparing TCFs with wide spectrum and high performance.
- 23 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (23) , 38945-38951
Cross-Aligned Silver Nanowires With Broad-Spectrum High Transmittance and Conductivity for Photodetectors
Transparent conductive films (TCFs) with low sheet resistance (Rsh) and high optical transmittance in the visible and infrared regions are essential components of a wide range of optoelectronic devices. Silver nanowires (AgNWs) have attracted significant attention due to their superior flexibility, conductivity, and transparency. However, TCFs prepared by commonly used film-forming methods such as spin coating suffer from a trade-off between conductivity and transmittance, which results in diminished device performance. Here we report a layer-by-layer agitation assisted alignment technique to fabricate highly aligned AgNWs films for transparent electrodes. The effects of solution concentration, rotation speed, and treatment time on the morphology, transmittance, and sheet resistance of the aligned AgNWs films were investigated systematically. Compared to randomly distributed AgNWs, optoelectronic performance was greatly improved, and the final film had a transmittance of 91.07% at 550 nm and a sheet resistance of 27.5 Ω/sq. Research findings indicate that optimized silver nanowire (AgNWs) electrodes can be successfully utilized to fabricate high-performance silicon-based photodetectors. Compared to previous designs, these detectors exhibit a 13.3% increase in external quantum efficiency at a wavelength of 850 nm. This study offers a low-cost and simple method for aligned AgNWs films, which has great potential for use in optoelectronic devices.
- 23 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (23) , 38945-38951
Cross-Aligned Silver Nanowires With Broad-Spectrum High Transmittance and Conductivity for Photodetectors
Transparent conductive films (TCFs) with low sheet resistance (Rsh) and high optical transmittance in the visible and infrared regions are essential components of a wide range of optoelectronic devices. Silver nanowires (AgNWs) have attracted significant attention due to their superior flexibility, conductivity, and transparency. However, TCFs prepared by commonly used film-forming methods such as spin coating suffer from a trade-off between conductivity and transmittance, which results in diminished device performance. Here we report a layer-by-layer agitation assisted alignment technique to fabricate highly aligned AgNWs films for transparent electrodes. The effects of solution concentration, rotation speed, and treatment time on the morphology, transmittance, and sheet resistance of the aligned AgNWs films were investigated systematically. Compared to randomly distributed AgNWs, optoelectronic performance was greatly improved, and the final film had a transmittance of 91.07% at 550 nm and a sheet resistance of 27.5 Ω/sq. Research findings indicate that optimized silver nanowire (AgNWs) electrodes can be successfully utilized to fabricate high-performance silicon-based photodetectors. Compared to previous designs, these detectors exhibit a 13.3% increase in external quantum efficiency at a wavelength of 850 nm. This study offers a low-cost and simple method for aligned AgNWs films, which has great potential for use in optoelectronic devices.
- 1 January 2024
- Published by Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences in Chinese Optics
- Vol. 17 (4) , 852-861
Vortex phase-shifting digital holography for micro-optical element surface topography measurment
The predecessor of China Optics was China Optics and Applied Optics Digest, which was founded in 1985. At that time, it was the only retrieval journal in the field of optics in China. At the end of 2008, China Optics and Applied Optics Digest was renamed 《中国光学》的前身是1985年创办的《中国光学与应用光学文摘》,当时是国内光学领域唯一的检索刊物。2008年底《中国光学与应用光学文摘》转型更名为《中国光学与应用光学》期刊,刊载内容突破了文摘的限制,正式成为学术刊物。
- 1 January 2024
- Published by Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences in Chinese Optics
- Vol. 17 (4) , 852-861
Vortex phase-shifting digital holography for micro-optical element surface topography measurment
The predecessor of China Optics was China Optics and Applied Optics Digest, which was founded in 1985. At that time, it was the only retrieval journal in the field of optics in China. At the end of 2008, China Optics and Applied Optics Digest was renamed 《中国光学》的前身是1985年创办的《中国光学与应用光学文摘》,当时是国内光学领域唯一的检索刊物。2008年底《中国光学与应用光学文摘》转型更名为《中国光学与应用光学》期刊,刊载内容突破了文摘的限制,正式成为学术刊物。
- Open Access
- 10 October 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (19) , 3540
Study on Ultrathin Silver Film Transparent Electrodes Based on Aluminum Seed Layers with Different Structures
Ag has the lowest electrical resistivity among all metals, and at the same time, the best optical properties in the visible and near-IR spectral range; it is therefore the most widely employed material for thin-metal-film-based transparent conductors. In this work, an ultra-thin transparent silver film electrode with aluminum as seed layer was prepared by a resistive thermal evaporation technique. Using a range of electrical, optical and surface morphology techniques, it can be noted that the presence of the thin layer of aluminum changes the growth kinetics (nucleation and evolution) of the thermal evaporation of Ag, leading to silver films with smooth surface morphology and high electrical conductivity, and the threshold thickness of the silver film is reduced. It is inferred that the aluminum layer showed a good infiltration effect on the ultra-thin silver film, by analyzing the transmittance spectrum, sheet resistance and surface morphology. Moreover, the average transmittance of silver film with 10 nm is 40% in the 400–2500 nm band, whereas the sheet resistance is 13 Ωsq −1. A series of experiments show that the introduction of Al seed layer has certain effect on improving the properties of transparent conductive silver films. Then, a new method for deposition of 1 nm Al seed layer was proposed; that is, the 1 nm aluminum infiltrated layer is divided into two or more layers, and the average transmittance of silver film with 5 nm is 60% in the 400–2500 nm band, whereas the sheet resistance does not exceed 100 Ω sq−1.
- 10 October 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (19) , 3540
Open AccessStudy on Ultrathin Silver Film Transparent Electrodes Based on Aluminum Seed Layers with Different Structures
Ag has the lowest electrical resistivity among all metals, and at the same time, the best optical properties in the visible and near-IR spectral range; it is therefore the most widely employed material for thin-metal-film-based transparent conductors. In this work, an ultra-thin transparent silver film electrode with aluminum as seed layer was prepared by a resistive thermal evaporation technique. Using a range of electrical, optical and surface morphology techniques, it can be noted that the presence of the thin layer of aluminum changes the growth kinetics (nucleation and evolution) of the thermal evaporation of Ag, leading to silver films with smooth surface morphology and high electrical conductivity, and the threshold thickness of the silver film is reduced. It is inferred that the aluminum layer showed a good infiltration effect on the ultra-thin silver film, by analyzing the transmittance spectrum, sheet resistance and surface morphology. Moreover, the average transmittance of silver film with 10 nm is 40% in the 400–2500 nm band, whereas the sheet resistance is 13 Ωsq −1. A series of experiments show that the introduction of Al seed layer has certain effect on improving the properties of transparent conductive silver films. Then, a new method for deposition of 1 nm Al seed layer was proposed; that is, the 1 nm aluminum infiltrated layer is divided into two or more layers, and the average transmittance of silver film with 5 nm is 60% in the 400–2500 nm band, whereas the sheet resistance does not exceed 100 Ω sq−1.
- Open Access
- 26 August 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (17) , 2956
Performance Enhancement of Silver Nanowire-Based Transparent Electrodes by Ultraviolet Irradiation
Silver nanowires (AgNWs) are used as transparent electrodes (TE) in many devices. However, the contact mode between the nanowires is the biggest reason why the sheet resistance of silver nanowires is limited. Here, simple and effective ultraviolet (UV) irradiation welding is chosen to solve this problem. The influence of the power density of the UV irradiation on welding of the silver nanowires is studied and the fixed irradiation time is chosen as one minute. The range of the UV (380 nm) irradiation power is chosen from 30 mW/cm2 to 150 mW/cm2. First of all, the transmittance of the silver nanowire film is not found to be affected by the UV welding (400–11,000 nm). The sheet resistance of the silver nanowires decreases to 73.9% at 60 mW/cm2 and increases to 127.6% at 120 mW/cm2. The investigations on the UV irradiation time reveal that the sheet resistance of the AgNWs decreases continuously when the UV irradiation time is varied from 0 to 3 min, and drops to 57.3% of the initial value at 3 min. From 3–6 min of the continuous irradiation time, the change of the sheet resistance is not obvious, which reflects the self-limiting and self-termination of AgNWs welding. By changing the wavelength of the UV irradiation from 350–400 nm, it is found that the welding effect is best when the UV wavelength is 380 nm. The average transmittance, square resistance, and the figure of merit of the welded AgNWs at 400–780 nm are 95.98%, 56.5 Ω/sq, and 117.42 × 10−4 Ω−1, respectively. The UV-welded AgNWs are also used in silicon-based photodetectors, and the quantum efficiency of the device is improved obviously.
- 26 August 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (17) , 2956
Open AccessPerformance Enhancement of Silver Nanowire-Based Transparent Electrodes by Ultraviolet Irradiation
Silver nanowires (AgNWs) are used as transparent electrodes (TE) in many devices. However, the contact mode between the nanowires is the biggest reason why the sheet resistance of silver nanowires is limited. Here, simple and effective ultraviolet (UV) irradiation welding is chosen to solve this problem. The influence of the power density of the UV irradiation on welding of the silver nanowires is studied and the fixed irradiation time is chosen as one minute. The range of the UV (380 nm) irradiation power is chosen from 30 mW/cm2 to 150 mW/cm2. First of all, the transmittance of the silver nanowire film is not found to be affected by the UV welding (400–11,000 nm). The sheet resistance of the silver nanowires decreases to 73.9% at 60 mW/cm2 and increases to 127.6% at 120 mW/cm2. The investigations on the UV irradiation time reveal that the sheet resistance of the AgNWs decreases continuously when the UV irradiation time is varied from 0 to 3 min, and drops to 57.3% of the initial value at 3 min. From 3–6 min of the continuous irradiation time, the change of the sheet resistance is not obvious, which reflects the self-limiting and self-termination of AgNWs welding. By changing the wavelength of the UV irradiation from 350–400 nm, it is found that the welding effect is best when the UV wavelength is 380 nm. The average transmittance, square resistance, and the figure of merit of the welded AgNWs at 400–780 nm are 95.98%, 56.5 Ω/sq, and 117.42 × 10−4 Ω−1, respectively. The UV-welded AgNWs are also used in silicon-based photodetectors, and the quantum efficiency of the device is improved obviously.
- 1 January 2022
- Published by Journal of Applied Optics in Journal of Applied Optics
- Vol. 43 (5) , 980-985
Ultra-thin silver transparent conductive film based on aluminum infiltration layer
The ultra-thin silver film is a potential material used for transparent conductive electrodes because of its high flexibility and excellent photoelectric properties. The ultra-thin silver transparent conductive films were prepared by resistance thermal evaporation technology using aluminum as infiltration layer. The threshold thickness of the silver film was reduced by introducing an aluminum infiltration layer, so that the silver film could be continuous on the K9 glass substrate at the lowest possible thickness. The resistance of silver film squares on aluminum infiltration layers with different thicknesses was tested, and verified by scanning electron microscope (SEM) images that the 1 nm aluminum infiltration layer had better infiltration effect on silver film. Then, the silver films with different thicknesses were prepared on 1 nm aluminum infiltration layer by the same process. The transmittance and square resistance test results show that the square resistance of 10 nm silver film prepared on 1 nm aluminum infiltration layer can reach 13 Ω/□, and the transmittance can reach more than 50% in the range of 0.4 μm~2.5 μm.
- 1 January 2022
- Published by Journal of Applied Optics in Journal of Applied Optics
- Vol. 43 (5) , 980-985
Ultra-thin silver transparent conductive film based on aluminum infiltration layer
The ultra-thin silver film is a potential material used for transparent conductive electrodes because of its high flexibility and excellent photoelectric properties. The ultra-thin silver transparent conductive films were prepared by resistance thermal evaporation technology using aluminum as infiltration layer. The threshold thickness of the silver film was reduced by introducing an aluminum infiltration layer, so that the silver film could be continuous on the K9 glass substrate at the lowest possible thickness. The resistance of silver film squares on aluminum infiltration layers with different thicknesses was tested, and verified by scanning electron microscope (SEM) images that the 1 nm aluminum infiltration layer had better infiltration effect on silver film. Then, the silver films with different thicknesses were prepared on 1 nm aluminum infiltration layer by the same process. The transmittance and square resistance test results show that the square resistance of 10 nm silver film prepared on 1 nm aluminum infiltration layer can reach 13 Ω/□, and the transmittance can reach more than 50% in the range of 0.4 μm~2.5 μm.
- 9 October 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 100 (5-8) , 1767-1777
Improvement in accuracy of micro-dimple arrays prepared by micro-electrochemical machining with high-pressure hydrostatic electrolyte
- 9 October 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 100 (5-8) , 1767-1777
Improvement in accuracy of micro-dimple arrays prepared by micro-electrochemical machining with high-pressure hydrostatic electrolyte
- 1 January 2018
- Published by Journal of Applied Optics in Journal of Applied Optics
- Vol. 39 (3) , 98-102
Study on surface roughness of titanium dioxide thin film
- 1 January 2018
- Published by Journal of Applied Optics in Journal of Applied Optics
- Vol. 39 (3) , 98-102
Study on surface roughness of titanium dioxide thin film