Miguel Duarte
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Miguel Duarte has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Adélio Mendes
University of Porto Rua Dr. Roberto Frias
2 shared publications - Bert De Mot
Research Group Applied Electrochemistry and Catalysis (ELCAT), University of Antwerp, Universiteitsplein 1, 2610Wilrijk, Belgium
1 shared publication - Celina Fernandes1 shared publication
Daniel Arenas-Esteban
1 shared publication- David G. Bucknall
Institute of Chemical Sciences, School of Engineering and Physical Sciences, Heriot-Watt University, Edinburgh EH14 4AS, UK
1 shared publication - Duncan Paul Fagg
TEMA – Centre for Mechanical Technology and Automation, Department of Mechanical Engineering, University of Aveiro, 3810-193 Aveiro, Portugal
1 shared publication
Latest Publications
- Open Access
- 29 July 2026
- Published by Elsevier in SSRN Electronic Journal
Antimony-doped tin oxide as an efficient catalyst in polysulfide aqueous redox flow batteries
Polysulfide-based aqueous redox flow batteries (RFB) offer an attractive alternative for scalable, long-term energy storage due to the remarkable polysulfide energy density, abundance, and low cost. However, their complex electrochemical kinetics, especially during RFB charging, limit the battery efficiency and prevent its commercial implementation. Here, an antimony-doped tin oxide (ATO) catalyst has been introduced to facilitate the reduction of the polysulfide-based electrolytes and battery charging. The ATO catalysed system achieved an 87.1 % energy efficiency at 10 mA cm-2, 48 % higher than the uncatalysed system, and reached 69.3 % at 40 mA cm-2. The scaling capacity of the ATO system was tested in a four-cell RFB stack that demonstrated an unprecedented 82.8 % energy efficiency at 20 mA cm-2, of which 96.8 % was retained after 70 cycles. This work presents a promising catalyst that addresses the practical limitations of polysulfide-based RFB.
- 29 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAntimony-doped tin oxide as an efficient catalyst in polysulfide aqueous redox flow batteries
Polysulfide-based aqueous redox flow batteries (RFB) offer an attractive alternative for scalable, long-term energy storage due to the remarkable polysulfide energy density, abundance, and low cost. However, their complex electrochemical kinetics, especially during RFB charging, limit the battery efficiency and prevent its commercial implementation. Here, an antimony-doped tin oxide (ATO) catalyst has been introduced to facilitate the reduction of the polysulfide-based electrolytes and battery charging. The ATO catalysed system achieved an 87.1 % energy efficiency at 10 mA cm-2, 48 % higher than the uncatalysed system, and reached 69.3 % at 40 mA cm-2. The scaling capacity of the ATO system was tested in a four-cell RFB stack that demonstrated an unprecedented 82.8 % energy efficiency at 20 mA cm-2, of which 96.8 % was retained after 70 cycles. This work presents a promising catalyst that addresses the practical limitations of polysulfide-based RFB.
- Open Access
- 22 November 2024
- Published by Elsevier in Chemical Engineering Journal
- Vol. 502
Nitrous oxide abatement and valorization in an ammonia-fueled SOFC stack – Nitric oxide and electricity production
- 22 November 2024
- Published by Elsevier in Chemical Engineering Journal
- Vol. 502
Open AccessNitrous oxide abatement and valorization in an ammonia-fueled SOFC stack – Nitric oxide and electricity production
- 1 August 2021
- Published by Elsevier in Journal of CO2 Utilization
- Vol. 50
Enhanced CO2 electroreduction with metal-nitrogen-doped carbons in a continuous flow reactor
- 1 August 2021
- Published by Elsevier in Journal of CO2 Utilization
- Vol. 50
Enhanced CO2 electroreduction with metal-nitrogen-doped carbons in a continuous flow reactor
- 18 November 2019
- Published by Wiley in ChemElectroChem
- Vol. 6 (22) , 5596-5602
Electrochemical Reduction of CO2: Effect of Convective CO2 Supply in Gas Diffusion Electrodes
The electrochemical reduction of carbon dioxide (CO2) is a promising technology in light of energy transition and industrial electrification. In this study, two different electrolyzer configurations, flow‐through and flow‐by modes, were analyzed for the production of carbon monoxide to resolve the CO2 mass‐transfer limitation problem at high current densities in gas diffusion electrodes. These two configurations respectively state convective and diffusive flow inside the gas diffusion layer, and their effect was studied on the cathodic performance of the electrolyzer by varying the operating conditions: cathodic potential, electrocatalyst loading, and Nafion content. In flow‐through configuration, a current density of 220 mA/cm2 could be achieved at a faradaic efficiency of 90 %; whereas, in the flow‐by configuration, the current density was at the same faradaic efficiency limited to 140 mA/cm2. However, the flow‐through configuration has a few limitations, such as lower energy efficiency, owing to the higher ohmic drop and the faster deactivation caused by crystallization of electrolyte salts inside the gas diffusion electrode. Therefore, flow‐by mode is currently the most adequate configuration for the long‐term operation of electrolyzers for the reduction of CO2 to CO. This study represents an essential step toward the application of electrolyzers for the electroreduction of CO2.
- 18 November 2019
- Published by Wiley in ChemElectroChem
- Vol. 6 (22) , 5596-5602
Electrochemical Reduction of CO2: Effect of Convective CO2 Supply in Gas Diffusion Electrodes
The electrochemical reduction of carbon dioxide (CO2) is a promising technology in light of energy transition and industrial electrification. In this study, two different electrolyzer configurations, flow‐through and flow‐by modes, were analyzed for the production of carbon monoxide to resolve the CO2 mass‐transfer limitation problem at high current densities in gas diffusion electrodes. These two configurations respectively state convective and diffusive flow inside the gas diffusion layer, and their effect was studied on the cathodic performance of the electrolyzer by varying the operating conditions: cathodic potential, electrocatalyst loading, and Nafion content. In flow‐through configuration, a current density of 220 mA/cm2 could be achieved at a faradaic efficiency of 90 %; whereas, in the flow‐by configuration, the current density was at the same faradaic efficiency limited to 140 mA/cm2. However, the flow‐through configuration has a few limitations, such as lower energy efficiency, owing to the higher ohmic drop and the faster deactivation caused by crystallization of electrolyte salts inside the gas diffusion electrode. Therefore, flow‐by mode is currently the most adequate configuration for the long‐term operation of electrolyzers for the reduction of CO2 to CO. This study represents an essential step toward the application of electrolyzers for the electroreduction of CO2.